Firewire camcorder and XP
 

I have tried to plug my camcorder into my PC via the firewire (2 seperate
cards) and it is no longer being found. No little balloon is appearing to
indicate that it has been detected. I am not certain if I the last time I
tried this I had SP2 on or not. I have borrowed a friends camcorder and it
too was not detected so I am assuming it is not the camcorder that is at
fault.

I have also tried my camcorder on a friends latop (also windows xp sp2).
This wasn't found either. I have an ipod which is still working OK through
the firewire so I know that the hardware is still working. I have tried 3
different cables for the camcorder to know effect.

I am at that point where I am going to perform a fresh install of windows xp
in the hope this sorts the problem (I have already tried various tricks such
as replacing the drivers with SP1 versions). I have also noted that I have
a error with the SM Bus Master not having the necessary drivers installed.
Could this have any affect on the camcorder? It is an asus motherboard with
a SiS648 chip so the intel inf update does not help. I have put on the
latest chipset update for the chip but it didn't make that error go away.

If anyone has any advice I would appreciate it.

On Fri, 28 Jan 2005 08:59:51 -0000, "Philip Rayne"
wrote:

I have tried to plug my camcorder into my PC via the firewire (2 seperate
cards) and it is no longer being found. No little balloon is appearing to
indicate that it has been detected. I am not certain if I the last time I
tried this I had SP2 on or not. I have borrowed a friends camcorder and it
too was not detected so I am assuming it is not the camcorder that is at
fault.

Go to the properties of your network connections.
Select the Firewire interface and disable the firewall for this
connection.
(That is: if you are sure there is no virus in your camcorder :-)

--
Kind regards,
Gerard Bok

First try to uninstall the firewire on your machine, and then re-install it
again, using the proper drivers. It is also possible to have a defective
firewire port.

I have used XP-SP1, and XP-SP2 with firewire ports, and everything worked
okay.

I had a friend that after installing SP2 his mouse went dead. He
re-installed it, and it still did not come back to life. I came over and
completely uninstalled the mouse, to make the machine mouseless. Then after
it was re-started this way, I disabled the auto-restore, re-started the
machine again, and then re-installed the mouse as if it was its first one.
After the new mouse was working, I re-enabled the auto restore, and
everything worked okay.

--

Jerry G.
=====

"Philip Rayne" wrote in message
...
I have tried to plug my camcorder into my PC via the firewire (2 seperate
cards) and it is no longer being found. No little balloon is appearing to
indicate that it has been detected. I am not certain if I the last time I
tried this I had SP2 on or not. I have borrowed a friends camcorder and it
too was not detected so I am assuming it is not the camcorder that is at
fault.

I have also tried my camcorder on a friends latop (also windows xp sp2).
This wasn't found either. I have an ipod which is still working OK through
the firewire so I know that the hardware is still working. I have tried 3
different cables for the camcorder to know effect.

I am at that point where I am going to perform a fresh install of windows xp
in the hope this sorts the problem (I have already tried various tricks such
as replacing the drivers with SP1 versions). I have also noted that I have
a error with the SM Bus Master not having the necessary drivers installed.
Could this have any affect on the camcorder? It is an asus motherboard with
a SiS648 chip so the intel inf update does not help. I have put on the
latest chipset update for the chip but it didn't make that error go away.

If anyone has any advice I would appreciate it.

I am having similar problems. I will give this a shot. One question,
though, how do you "disable the auto-restore"?

Jerry G. wrote:
First try to uninstall the firewire on your machine, and then
re-install it
again, using the proper drivers. It is also possible to have a
defective
firewire port.

I have used XP-SP1, and XP-SP2 with firewire ports, and everything
worked
okay.

I had a friend that after installing SP2 his mouse went dead. He
re-installed it, and it still did not come back to life. I came over
and
completely uninstalled the mouse, to make the machine mouseless. Then
after
it was re-started this way, I disabled the auto-restore, re-started
the
machine again, and then re-installed the mouse as if it was its first
one.
After the new mouse was working, I re-enabled the auto restore, and
everything worked okay.

--

Jerry G.
=====

"Philip Rayne" wrote in message
...
I have tried to plug my camcorder into my PC via the firewire (2
seperate
cards) and it is no longer being found. No little balloon is
appearing to
indicate that it has been detected. I am not certain if I the last
time I
tried this I had SP2 on or not. I have borrowed a friends camcorder
and it
too was not detected so I am assuming it is not the camcorder that is
at
fault.

I have also tried my camcorder on a friends latop (also windows xp
sp2).
This wasn't found either. I have an ipod which is still working OK
through
the firewire so I know that the hardware is still working. I have
tried 3
different cables for the camcorder to know effect.

I am at that point where I am going to perform a fresh install of
windows xp
in the hope this sorts the problem (I have already tried various
tricks such
as replacing the drivers with SP1 versions). I have also noted that
I have
a error with the SM Bus Master not having the necessary drivers
installed.
Could this have any affect on the camcorder? It is an asus
motherboard with
a SiS648 chip so the intel inf update does not help. I have put on
the
latest chipset update for the chip but it didn't make that error go
away.

If anyone has any advice I would appreciate it.