|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
August 29th 03, 11:26 AM
|
|||
|
|||
P4 Frequency
I have a GA-8IRXP mainboard with a 1.6 GHz P4 Intel processor.
After a cold boot the speed of the of the processor is 1077 MHz (Checked with Intel's software and with Aida) and stays the same for all hot boots.. If I turn the computer off when it is still in the bios boot sequence and immediately afterwards turn it on again (on-off-on) I get the expected speed of 1600 MHz, it stays at the same speed until the next cold boot. Any ideas as to the reason for that. Isaac Amarel 
|
|
#2
August 29th 03, 11:46 PM
|
|||
|
|||
|
"Isaac Amarel" wrote in message ... I have a GA-8IRXP mainboard with a 1.6 GHz P4 Intel processor. After a cold boot the speed of the of the processor is 1077 MHz (Checked with Intel's software and with Aida) and stays the same for all hot boots.. If I turn the computer off when it is still in the bios boot sequence and immediately afterwards turn it on again (on-off-on) I get the expected speed of 1600 MHz, it stays at the same speed until the next cold boot. Any ideas as to the reason for that. I expected to see the 3.2Ghz for my processor as well with the 8KNXP board I bought, but didn't, until I changed it in the bios. That kind of crap shouldn't happen, IMO. Gigabyte bios issues appear to be legion, at least from the ng posts we all see.
|
|
#3
August 30th 03, 12:24 AM
|
|||
|
|||
|
My 3.2Ghz has worked perfectly right from the first power-up with no changes
in the BIOS ever needed. "CriticalMass" wrote in message ... "Isaac Amarel" wrote in message ... I have a GA-8IRXP mainboard with a 1.6 GHz P4 Intel processor. After a cold boot the speed of the of the processor is 1077 MHz (Checked with Intel's software and with Aida) and stays the same for all hot boots.. If I turn the computer off when it is still in the bios boot sequence and immediately afterwards turn it on again (on-off-on) I get the expected speed of 1600 MHz, it stays at the same speed until the next cold boot. Any ideas as to the reason for that. I expected to see the 3.2Ghz for my processor as well with the 8KNXP board I bought, but didn't, until I changed it in the bios. That kind of crap shouldn't happen, IMO. Gigabyte bios issues appear to be legion, at least from the ng posts we all see.
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| How can you tell which memory frequency? | Langholm | General | 4 | August 17th 04 11:42 PM |
| A7N8X Dlx - How does MBM5 read the CPU frequency ? | Gino Zantafio | Asus Motherboards | 0 | December 11th 03 09:21 PM |
| p3c-d and cloick frequency | bigbinc | Asus Motherboards | 0 | November 22nd 03 06:08 PM |
| A7N8X CPU Frequency | Ron | Asus Motherboards | 7 | July 30th 03 11:56 AM |
| Optimal bios settings? cpu external frequency settings? etc | Mothra | Asus Motherboards | 8 | July 4th 03 04:21 AM |
Linear Mode
