If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
GigaByte GA-7DXR Memory Problem ?
I wonder is there solution for this problem:
System: MBO: Gigabyte 7DXR bios f10a CPU: AMT AthlonXP 1800+ at 1533MHz AGP: Sapphire Radeon 9000 VIVO OS: WindowsXP Pro SP1 Memory: DIMM1 PC-2100, 512 MB, 184 pins, DDR RAM, 266 MHz, M.tec TTD7608F8E75B DIMM2 PC-2100, 512 MB, 184 pins, DDR RAM, 266 MHz, Infineon-Hynix HY5DU56822AT-H Problem: Working with mpeg2 files in VirtualDub freezes my computer that only hard reset helps. OK, I got one mpeg2 file in VirtualDub, and simple freeze test is that I start error scan and it freezes after 2-5 min. And it only happens when both memory modules are in computer. I tested each module individually plugged in computer, and there are no problems. I tested memory in DOS with DocMem, and all tests are OK. All bios parameters are default and auto memory parameters a 8 8 10 3 7 2.5 3 I found at newsgroups some stuff on similar problems and suggestions to increase memory voltage from 2.5V to 2.6V or 2.7V and to setup memory parameters manually to 16 8 8 2 6 2 2. I tried to increase voltage but it does not help, and with these manual parameters I can't even boot to Windows (it just restarts before windows booting or hangs after HD detection). So, is there any solution for this configuration or I just need same two memory modules? Thanks. -- GrgArt www.kaos.hr |
#2
|
|||
|
|||
Iam using an AthlonXP 1800+ TBred B at 155x12.5 with 2x256MB PC2700 Nanya
and a GeForce 3 Ti 200 and its rock solid.Probably you need to get two identical memory modules. "GrgArt" wrote in message ... I wonder is there solution for this problem: System: MBO: Gigabyte 7DXR bios f10a CPU: AMT AthlonXP 1800+ at 1533MHz AGP: Sapphire Radeon 9000 VIVO OS: WindowsXP Pro SP1 Memory: DIMM1 PC-2100, 512 MB, 184 pins, DDR RAM, 266 MHz, M.tec TTD7608F8E75B DIMM2 PC-2100, 512 MB, 184 pins, DDR RAM, 266 MHz, Infineon-Hynix HY5DU56822AT-H Problem: Working with mpeg2 files in VirtualDub freezes my computer that only hard reset helps. OK, I got one mpeg2 file in VirtualDub, and simple freeze test is that I start error scan and it freezes after 2-5 min. And it only happens when both memory modules are in computer. I tested each module individually plugged in computer, and there are no problems. I tested memory in DOS with DocMem, and all tests are OK. All bios parameters are default and auto memory parameters a 8 8 10 3 7 2.5 3 I found at newsgroups some stuff on similar problems and suggestions to increase memory voltage from 2.5V to 2.6V or 2.7V and to setup memory parameters manually to 16 8 8 2 6 2 2. I tried to increase voltage but it does not help, and with these manual parameters I can't even boot to Windows (it just restarts before windows booting or hangs after HD detection). So, is there any solution for this configuration or I just need same two memory modules? Thanks. -- GrgArt www.kaos.hr |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Iwill DU3160 controller on Gigabyte 1000MK problem | Bubba | General | 4 | December 23rd 04 01:19 PM |
Memory Problem: doom3 and Halflife2 Crashing | David B Lake-Jones | General | 4 | December 5th 04 04:15 PM |
memory problem | The_Pittmans | General | 3 | June 22nd 04 05:31 PM |
Mysterious memory problem solves itself. | half_pint | General | 6 | April 15th 04 05:54 AM |
Disk to disk copying with overclocked memory | JT | General | 30 | March 21st 04 03:22 AM |