If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
VGAsilencerV3 aftermarket cooler for 7800 cards
Before you peel those lil stickers off the heat contact pads, KNOW you will
not want to unstick things later because man they STICK like GLUE. And the directions that come with the VGAsilencer kinda suck EVEN if you read them, hehe, because I didn't until it was too late. AND I don't think they took the exact design of the 7800 GTX in consideration enough when they designed that V3 of the VGAsilencer. BUT it CAN work very well with little effort if you are careful. That's why I'm posting this. Be very careful when you try fitting that heatsink for the chips on the back of the card and knowing you will be able to screw it down BEFORE you put the stuff (heatsink & fan) onto the front of the video card because the parts that go on the back of the card REQUIRE you to use some kind of bolts on the front for the screws that fasten the back-heatsink (that flatish piece of metal that really you can probably use the one that came with the card as they seem very much alike and I'd like to know what type of metal each [default one from XFX and one that comes with VGA silencer] is) need something to screw INTO. See, I put the VGAsilencer onto the front of the card and then got to the back and realized I needed to take the front stuff off and tried to pull it off and those heat sink pads are like glue! So then I was afraid I'd pull the chips from the board so I tried those computer-common screws that typically screw your case door onto your case (wider than hard drive screws) and LUCKILY they are the perfect size to screw that back-of-the-video-card heatsink into the video card board material and HOLD it without needing bolts. The other thing: The VGASilencer V3 comes with those sticky pads for the DDR3 RAM lined up in sets of 2 on the VGAsilencer's heatsink for front of card. Well. You need to remove half of them and use them for the back of the card. I didn't realize that before I bolted/stuck the VGAsilencer to my 7800 GTX. So. Please don't call me a dumbass, okay? Heh. I'm swallowing my pride to share this lil mishap so you all don't make the same mistakes I did. See, my last card was a BFG 6800 GT OC and I had put a VGAsilencer on it and there was nothing to do with the back of the card so this time around I was overly confident and just did everything without the directions until I realized there was stuff to do with the back of the card. LUCKILY, it's all working ok and nothing is damaged and wow that VGAsilencer really does drop the deg. C about 8 to 10, which is very nice! And expelling the warm air out the back of the case is nice, too! -- Scotter Tyan Thunder K8WE Dual Opteron 252s (2.6ghz) 6 gig DDR400 RAM XFX 7800 GTX 256 500 gig SATA2 Hitachi Dual 24" Dell LCDs 550W power supply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Hardcore gamer is little upset. | Ryan Atici | Asus Motherboards | 16 | December 26th 04 03:26 AM |
Arctic Cooler for VGA cards | Stoneskin | Overclocking | 0 | March 31st 04 03:38 PM |
Why doesn't ATI make VIVO cards anymore , I don't want TV SH*T, just capability of recording VIDEO IN! | [email protected] | Ati Videocards | 10 | January 28th 04 04:43 AM |
Can't Run 2 ATI Radeon Cards in my W2K Box--HELP! | Ken Fox | Ati Videocards | 5 | December 15th 03 03:06 PM |
P4P800Dlx W2K Won't Run 2 Video Cards | Ken Fox | Asus Motherboards | 2 | December 13th 03 08:29 AM |