If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Build Your Own ATX Power On Switch
Got a small problem.
have motherboard set up w/ fan, heatsink, hd, etc. but the case I'm using is a Gateway case and the wires coming from the power on switch (the external button you press to turn the computer on) are in a 8x8 plastic thing and there's 6 wires. The motherboard clearly has 2 prongs set aside for an ATX-SW but the case doesn't seem to support this. Does anyone know how to build a simple power on switch that goes to the motherboard? Or does anyone know which two wires from an Gateway case are supposed to go into the atx-sw? e-mail me if u can. Thanks, A |
#2
|
|||
|
|||
alj wrote:
Got a small problem. have motherboard set up w/ fan, heatsink, hd, etc. but the case I'm using is a Gateway case and the wires coming from the power on switch (the external button you press to turn the computer on) are in a 8x8 plastic thing and there's 6 wires. The motherboard clearly has 2 prongs set aside for an ATX-SW but the case doesn't seem to support this. Does anyone know how to build a simple power on switch that goes to the motherboard? Or does anyone know which two wires from an Gateway case are supposed to go into the atx-sw? e-mail me if u can. Thanks, A just check the wires with an ohm-meter the swich is just a single pole , momentary "on" |
#3
|
|||
|
|||
just check the wires with an ohm-meter the swich is just a single pole , momentary "on" there's two prongs for atx, so the one thing is just one wire? Thanks, A |
#4
|
|||
|
|||
alj wrote:
just check the wires with an ohm-meter the swich is just a single pole , momentary "on" there's two prongs for atx, so the one thing is just one wire? Thanks, A There are six wires. You are looking for the correct two out of those six. Choose two at a time and connect the ohmmeter across the two. Press and hold the power button. If the reading goes from near infinity with the button unpressed to near zero with the button pressed, you have found the correct pair. There are 15 (ie 5+4+3+2+1) possible pairings from the six wires. Keep trying pairs until you find the correct one, then connect one of those two wires to one of the pins on the motherboard. Then connect the other wire to the other pin on the motherboard. It doesn't matter which of the pair of wires goes to which pin of the two pins. |
#5
|
|||
|
|||
Matt wrote:
alj wrote: just check the wires with an ohm-meter the swich is just a single pole , momentary "on" there's two prongs for atx, so the one thing is just one wire? Thanks, A Second draft: There are six wires. You are looking for the correct two out of those six. Choose two at a time and connect the ohmmeter across the two. Press and hold the power button. If the reading goes from near infinity with the button unpressed to near zero with the button pressed, you have found the correct pair. There are 15 (ie 5+4+3+2+1) possible pairings from the six wires. Keep trying pairs until you find the correct pair, then connect one of those two wires to one of the pins on the motherboard. Then connect the other wire to the other pin on the motherboard. It doesn't matter which wire of the pair of wires goes to which of the two pins. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
NTL to PC and Xbox | Scott | Homebuilt PC's | 8 | September 14th 04 09:53 AM |
ATX power switch wires | anthony fidler | Homebuilt PC's | 4 | September 9th 04 06:47 PM |
Questions about power use | Purple | Homebuilt PC's | 8 | July 4th 04 12:45 AM |
Won't Power Up after Power Outage | Greg Lovern | Homebuilt PC's | 7 | February 8th 04 01:47 PM |
power switch won't boot up? | Larry Gagnon | General | 1 | January 16th 04 05:18 AM |