A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » General Hardware & Peripherals » Storage (alternative)
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

primary master hard disk fail



 
 
Thread Tools Display Modes
  #1  
Old May 11th 04, 12:30 PM
berthold
external usenet poster
 
Posts: n/a
Default primary master hard disk fail

Hy,

getting this error message "primary master hard disk fail"; after
booting an ibm hard disk with a "maxtor draco" macintosh disk.

Award Plug&Play Bios says:

1st screen
Detecting IDE Primary Master...... IC35L060AVER07-0
Detecting IDE Primary Slave...... Maxtor Draco
Detecting IDE Secondary Master.......CR-48XATE
Detecting IDE Secondary Slave......None

2nd screen
Prim. Master Disk: None
Primary Slave Disk: None
Secondary Master Disk: CR-48XATE
Secondary Slave Disk: None

Diagnostics with Powermax displays error-codes: UKOE02, S57,
BiosExtensionSupport - failed, Partition information - read fail.

MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive
Fitness Test does it, but could not handle the MacIntosh hard disk.

Anyone has an idea what to do? Are there other diagnostics tools for
windows which can handle Mac hard disks?

Any help would be appreciated.
Thanks in advance
Regards,
berthold

Some additional details:

serial, model/GTLA:
S/N K80FEMVC
54098U8

Motherboard, chip
Medion MD9901, MicroATX
Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache
Intel ZX, Intel PIIX4E

Powermax-Diagnostics
Error-Codes: UKOE02, S57,
BiosExtensionSupport - failed
Partition information - read fail
  #2  
Old May 11th 04, 12:49 PM
Alan Walker
external usenet poster
 
Posts: n/a
Default

berthold wrote:
Hy,

getting this error message "primary master hard disk fail"; after
booting an ibm hard disk with a "maxtor draco" macintosh disk.

Award Plug&Play Bios says:

1st screen
Detecting IDE Primary Master...... IC35L060AVER07-0
Detecting IDE Primary Slave...... Maxtor Draco
Detecting IDE Secondary Master.......CR-48XATE
Detecting IDE Secondary Slave......None

2nd screen
Prim. Master Disk: None
Primary Slave Disk: None
Secondary Master Disk: CR-48XATE
Secondary Slave Disk: None

Diagnostics with Powermax displays error-codes: UKOE02, S57,
BiosExtensionSupport - failed, Partition information - read fail.

MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive
Fitness Test does it, but could not handle the MacIntosh hard disk.

Anyone has an idea what to do? Are there other diagnostics tools for
windows which can handle Mac hard disks?

Any help would be appreciated.
Thanks in advance
Regards,
berthold

Some additional details:

serial, model/GTLA:
S/N K80FEMVC
54098U8

Motherboard, chip
Medion MD9901, MicroATX
Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache
Intel ZX, Intel PIIX4E

Powermax-Diagnostics
Error-Codes: UKOE02, S57,
BiosExtensionSupport - failed
Partition information - read fail


Swap primary/secondary IDE cables at mobo end and let us know what it says.

Might be IDE controller dead/failing.

Alan


  #3  
Old May 11th 04, 08:53 PM
Folkert Rienstra
external usenet poster
 
Posts: n/a
Default

"berthold" wrote in message om...
Hi,

getting this error message "primary master hard disk fail"; after
booting an ibm hard disk with a "maxtor draco" macintosh disk.

Award Plug&Play Bios says:

1st screen
Detecting IDE Primary Master...... IC35L060AVER07-0


Detecting IDE Primary Slave...... Maxtor Draco


"Maxtor Draco" means that it is either dead or not set to spin-up auto.
Since the IBM cannot be read either the Maxtor is likely dead.

Detecting IDE Secondary Master.......CR-48XATE
Detecting IDE Secondary Slave......None

2nd screen
Prim. Master Disk: None
Primary Slave Disk: None
Secondary Master Disk: CR-48XATE
Secondary Slave Disk: None

Diagnostics with Powermax displays error-codes: UKOE02, S57,
BiosExtensionSupport - failed, Partition information - read fail.

MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive
Fitness Test does it, but could not handle the MacIntosh hard disk.

Anyone has an idea what to do? Are there other diagnostics tools for
windows which can handle Mac hard disks?


Put the Maxtor alone on its own cable, see what changes.


Any help would be appreciated.
Thanks in advance
Regards,
berthold

Some additional details:

serial, model/GTLA:
S/N K80FEMVC
54098U8

Motherboard, chip
Medion MD9901, MicroATX
Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache
Intel ZX, Intel PIIX4E

Powermax-Diagnostics
Error-Codes: UKOE02, S57,
BiosExtensionSupport - failed
Partition information - read fail

  #4  
Old May 14th 04, 02:28 PM
berthold
external usenet poster
 
Posts: n/a
Default

tried a lot of things.

used the maxtor drive as:

primary master single and slave
Secondary master single and slave

even swapped the IDE cables on the motherboard. Checked and changed
always the jumpers.

But getting "...hard disk fail". Bios recognizes as "Maxtor Draco"
and the IBMs drive as "IC06035AVER07"

New details from IBMs Drive Fitness Test on Maxtor's Draco says:

Primary Master/Slave Maxtor Draco 10,25 GB (although it's a 40,9 GB
hdd)
ATA-5
Cache 2097 KB
Ultra DMA: Highest Mode: 4, Active Mode: None
Write Cache: enabled
read look-ahead: enabled
S.m.a.r.t. options: disabled
security feature not swapped

regards,
berthold




"Folkert Rienstra" wrote in message ...
"berthold" wrote in message om...
Hi,

getting this error message "primary master hard disk fail"; after
booting an ibm hard disk with a "maxtor draco" macintosh disk.

Award Plug&Play Bios says:

1st screen
Detecting IDE Primary Master...... IC35L060AVER07-0


Detecting IDE Primary Slave...... Maxtor Draco


"Maxtor Draco" means that it is either dead or not set to spin-up auto.
Since the IBM cannot be read either the Maxtor is likely dead.

Detecting IDE Secondary Master.......CR-48XATE
Detecting IDE Secondary Slave......None

2nd screen
Prim. Master Disk: None
Primary Slave Disk: None
Secondary Master Disk: CR-48XATE
Secondary Slave Disk: None

Diagnostics with Powermax displays error-codes: UKOE02, S57,
BiosExtensionSupport - failed, Partition information - read fail.

MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive
Fitness Test does it, but could not handle the MacIntosh hard disk.

Anyone has an idea what to do? Are there other diagnostics tools for
windows which can handle Mac hard disks?


Put the Maxtor alone on its own cable, see what changes.


Any help would be appreciated.
Thanks in advance
Regards,
berthold

Some additional details:

serial, model/GTLA:
S/N K80FEMVC
54098U8

Motherboard, chip
Medion MD9901, MicroATX
Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache
Intel ZX, Intel PIIX4E

Powermax-Diagnostics
Error-Codes: UKOE02, S57,
BiosExtensionSupport - failed
Partition information - read fail

  #5  
Old May 14th 04, 09:23 PM
Folkert Rienstra
external usenet poster
 
Posts: n/a
Default

"berthold" wrote in message om...
tried a lot of things.

used the maxtor drive as:

primary master single and slave
Secondary master single and slave

even swapped the IDE cables on the motherboard. Checked and changed
always the jumpers.

But getting "...hard disk fail". Bios recognizes as "Maxtor Draco"


So it's dead.

and the IBMs drive as "IC06035AVER07"

New details from IBMs Drive Fitness Test on Maxtor's Draco says:

Primary Master/Slave Maxtor Draco 10,25 GB (although it's a 40,9 GB hdd)


Probably the smallest size in the Draco series design.
The actual size is read from the platters once it has spun-up.

ATA-5
Cache 2097 KB
Ultra DMA: Highest Mode: 4, Active Mode: None
Write Cache: enabled
read look-ahead: enabled
S.m.a.r.t. options: disabled
security feature not swapped

regards,
berthold




"Folkert Rienstra" wrote in message ...
"berthold" wrote in message om...
Hi,

getting this error message "primary master hard disk fail"; after
booting an ibm hard disk with a "maxtor draco" macintosh disk.

Award Plug&Play Bios says:

1st screen
Detecting IDE Primary Master...... IC35L060AVER07-0


Detecting IDE Primary Slave...... Maxtor Draco


"Maxtor Draco" means that it is either dead or not set to spin-up auto.
Since the IBM cannot be read either the Maxtor is likely dead.

Detecting IDE Secondary Master.......CR-48XATE
Detecting IDE Secondary Slave......None

2nd screen
Prim. Master Disk: None
Primary Slave Disk: None
Secondary Master Disk: CR-48XATE
Secondary Slave Disk: None

Diagnostics with Powermax displays error-codes: UKOE02, S57,
BiosExtensionSupport - failed, Partition information - read fail.

MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive
Fitness Test does it, but could not handle the MacIntosh hard disk.

Anyone has an idea what to do? Are there other diagnostics tools for
windows which can handle Mac hard disks?


Put the Maxtor alone on its own cable, see what changes.


Any help would be appreciated.
Thanks in advance
Regards,
berthold

Some additional details:

serial, model/GTLA:
S/N K80FEMVC
54098U8

Motherboard, chip
Medion MD9901, MicroATX
Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache
Intel ZX, Intel PIIX4E

Powermax-Diagnostics
Error-Codes: UKOE02, S57,
BiosExtensionSupport - failed
Partition information - read fail

  #6  
Old May 15th 04, 03:28 AM
CJT
external usenet poster
 
Posts: n/a
Default

berthold wrote:

tried a lot of things.


They make decent doorstops.


used the maxtor drive as:

primary master single and slave
Secondary master single and slave

even swapped the IDE cables on the motherboard. Checked and changed
always the jumpers.

But getting "...hard disk fail". Bios recognizes as "Maxtor Draco"
and the IBMs drive as "IC06035AVER07"

New details from IBMs Drive Fitness Test on Maxtor's Draco says:

Primary Master/Slave Maxtor Draco 10,25 GB (although it's a 40,9 GB
hdd)
ATA-5
Cache 2097 KB
Ultra DMA: Highest Mode: 4, Active Mode: None
Write Cache: enabled
read look-ahead: enabled
S.m.a.r.t. options: disabled
security feature not swapped

regards,
berthold




"Folkert Rienstra" wrote in message ...

"berthold" wrote in message om...

Hi,

getting this error message "primary master hard disk fail"; after
booting an ibm hard disk with a "maxtor draco" macintosh disk.

Award Plug&Play Bios says:

1st screen
Detecting IDE Primary Master...... IC35L060AVER07-0




Detecting IDE Primary Slave...... Maxtor Draco


"Maxtor Draco" means that it is either dead or not set to spin-up auto.
Since the IBM cannot be read either the Maxtor is likely dead.


Detecting IDE Secondary Master.......CR-48XATE
Detecting IDE Secondary Slave......None

2nd screen
Prim. Master Disk: None
Primary Slave Disk: None
Secondary Master Disk: CR-48XATE
Secondary Slave Disk: None

Diagnostics with Powermax displays error-codes: UKOE02, S57,
BiosExtensionSupport - failed, Partition information - read fail.

MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive
Fitness Test does it, but could not handle the MacIntosh hard disk.

Anyone has an idea what to do? Are there other diagnostics tools for
windows which can handle Mac hard disks?


Put the Maxtor alone on its own cable, see what changes.


Any help would be appreciated.
Thanks in advance
Regards,
berthold

Some additional details:

serial, model/GTLA:
S/N K80FEMVC
54098U8

Motherboard, chip
Medion MD9901, MicroATX
Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache
Intel ZX, Intel PIIX4E

Powermax-Diagnostics
Error-Codes: UKOE02, S57,
BiosExtensionSupport - failed
Partition information - read fail



--
The e-mail address in our reply-to line is reversed in an attempt to
minimize spam. Our true address is of the form .
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Newbie: OC Advice: AMDXP2200 CPU Donald Bock Overclocking AMD Processors 2 March 12th 05 01:14 AM
Primary Hard Disk Drive 1 Not Found brandon General Hardware 5 July 18th 04 11:39 PM
RAID card for my PC?? TANKIE General 5 May 22nd 04 01:09 AM
SOLUTION! IBM Hard Drive only recognized as 33GB hard drive, but is more >>>82.3GB Andy Storage (alternative) 9 November 18th 03 12:20 AM
set CDROM as master not slave? kony General 1 June 28th 03 07:40 AM


All times are GMT +1. The time now is 01:36 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.