If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Promise Ultra 100
Hello,
I've got a Problem with my Promise Ultra 100 with one Samsung Sv1203N atached to each channel. Sometimes when I boot the Promise detects only the second disk, when I reboot it detects both. Can somebody help? Thank you |
#2
|
|||
|
|||
On Sat, 28 Jun 2003 18:12:38 +0200, "S. Pfeffer"
wrote: Hello, I've got a Problem with my Promise Ultra 100 with one Samsung Sv1203N atached to each channel. Sometimes when I boot the Promise detects only the second disk, when I reboot it detects both. Can somebody help? Thank you Try another IDE cable. |
#3
|
|||
|
|||
Ken wrote:
On Sat, 28 Jun 2003 18:12:38 +0200, "S. Pfeffer" wrote: I've got a Problem with my Promise Ultra 100 with one Samsung Sv1203N atached to each channel. Sometimes when I boot the Promise detects only the second disk, when I reboot it detects both. Can somebody help? Weak PSU? I don't think so. Its a 300W PSU, and there are only 3 disks and a cd-drive and a pentium 2 400 |
#4
|
|||
|
|||
Jim wrote:
What happens if you swap HDs? If the same channel fails, more likely the problem is in the controller (you might want to consider using the more reliable channel, as master + slave). If the other channel fails, more likely the problem is in the HD. Jim I've already done this. The disk on the first channel fails. There are only two disks, each as master at one channel. "S. Pfeffer" wrote in message ... Hello, I've got a Problem with my Promise Ultra 100 with one Samsung Sv1203N atached to each channel. Sometimes when I boot the Promise detects only the second disk, when I reboot it detects both. Can somebody help? Thank you |
#5
|
|||
|
|||
S. Pfeffer wrote:
Hello, I've got a Problem with my Promise Ultra 100 with one Samsung Sv1203N atached to each channel. Sometimes when I boot the Promise detects only the second disk, when I reboot it detects both. Can somebody help? Thank you Is there mo way disabling the HDD autodetection an tell the controller the harddisk parameters like on the motherboard? |
#6
|
|||
|
|||
If a quick boot is used the drives might not be ready in time. Enabling the memory test might provide enough of a delay for both drives to become ready before they are polled. "S. Pfeffer" wrote: Hello, I've got a Problem with my Promise Ultra 100 with one Samsung Sv1203N atached to each channel. Sometimes when I boot the Promise detects only the second disk, when I reboot it detects both. Can somebody help? Thank you -- Mike Walsh West Palm Beach, Florida, U.S.A. |
#7
|
|||
|
|||
Mike Walsh wrote:
If a quick boot is used the drives might not be ready in time. Enabling the memory test might provide enough of a delay for both drives to become ready before they are polled. "S. Pfeffer" wrote: Hello, I've got a Problem with my Promise Ultra 100 with one Samsung Sv1203N atached to each channel. Sometimes when I boot the Promise detects only the second disk, when I reboot it detects both. Can somebody help? Thank you You think the same as I thought. Before I posted here, I've changed these. Thank You |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
nVidia 5600 Ultra v. ATI Radeon 9600 | Christoph | General | 1 | June 27th 03 07:16 PM |