No USB 2.0 - MA785GM-USH2

Maybe someone out there can help.

I have a MA785GM-USH2 MB (rev 1.0). The system was recently built and
everything works perfectly.

However, I cannot get the USB ports to work as anything other than USB
1.1

I installed a dual boot of XP and Linux (Mandriva). Both installed
fine and XP then upgraded to SP3

The drivers in Device Manager show Standard OpenHCD USB Host
Controller. There is no mention of Enhanced drivers.

I have just ordered a Flash drive with 2.0 interface to see if it
tells me that the driver is not operating at full speed.

Reinstalled all ATI drivers as per Gigabytes directions. Still nothing
changes.

1. Should I see a different driver in the Device Driver window?
2. Any thoughts on how to get this to work?

As a side note, Linux shows the mouse as 2.0 but running at 1.1.While
I cannot expect them to support Linux, XP should work.

Thank you in advance for any suggestions.

wrote:
Maybe someone out there can help.

I have a MA785GM-USH2 MB (rev 1.0). The system was recently built and
everything works perfectly.

However, I cannot get the USB ports to work as anything other than USB
1.1

I installed a dual boot of XP and Linux (Mandriva). Both installed
fine and XP then upgraded to SP3

The drivers in Device Manager show Standard OpenHCD USB Host
Controller. There is no mention of Enhanced drivers.

I have just ordered a Flash drive with 2.0 interface to see if it
tells me that the driver is not operating at full speed.

Reinstalled all ATI drivers as per Gigabytes directions. Still nothing
changes.

1. Should I see a different driver in the Device Driver window?
2. Any thoughts on how to get this to work?

As a side note, Linux shows the mouse as 2.0 but running at 1.1.While
I cannot expect them to support Linux, XP should work.

Thank you in advance for any suggestions.

Check your BIOS setup screen, in the USB section.
Some boards allow disabling USB2 in there.
For example, see

"USB EHCI Controller" [Enabled]

The fact you can get a port to operate
at USB 1.1, tells me there probably isn't a problem
with bus power on the port. So the wires themselves are
all likely working.

HTH,
Paul

Thank you, that was it.

Do you know I went back and forth with Gigabyte about 6 times and they
never once suggested I check the bios.


On Mon, 03 May 2010 13:27:53 -0400, Paul wrote:

wrote:
Maybe someone out there can help.

I have a MA785GM-USH2 MB (rev 1.0). The system was recently built and
everything works perfectly.

However, I cannot get the USB ports to work as anything other than USB
1.1

I installed a dual boot of XP and Linux (Mandriva). Both installed
fine and XP then upgraded to SP3

The drivers in Device Manager show Standard OpenHCD USB Host
Controller. There is no mention of Enhanced drivers.

I have just ordered a Flash drive with 2.0 interface to see if it
tells me that the driver is not operating at full speed.

Reinstalled all ATI drivers as per Gigabytes directions. Still nothing
changes.

1. Should I see a different driver in the Device Driver window?
2. Any thoughts on how to get this to work?

As a side note, Linux shows the mouse as 2.0 but running at 1.1.While
I cannot expect them to support Linux, XP should work.

Thank you in advance for any suggestions.

Check your BIOS setup screen, in the USB section.
Some boards allow disabling USB2 in there.
For example, see

"USB EHCI Controller" [Enabled]

The fact you can get a port to operate
at USB 1.1, tells me there probably isn't a problem
with bus power on the port. So the wires themselves are
all likely working.

HTH,
Paul

wrote:
Thank you, that was it.

Do you know I went back and forth with Gigabyte about 6 times and they
never once suggested I check the bios.


Maybe they just forgot about that one.

Glad it's fixed.

Paul


On Mon, 03 May 2010 13:27:53 -0400, Paul wrote:

wrote:
Maybe someone out there can help.

I have a MA785GM-USH2 MB (rev 1.0). The system was recently built and
everything works perfectly.

However, I cannot get the USB ports to work as anything other than USB
1.1

I installed a dual boot of XP and Linux (Mandriva). Both installed
fine and XP then upgraded to SP3

The drivers in Device Manager show Standard OpenHCD USB Host
Controller. There is no mention of Enhanced drivers.

I have just ordered a Flash drive with 2.0 interface to see if it
tells me that the driver is not operating at full speed.

Reinstalled all ATI drivers as per Gigabytes directions. Still nothing
changes.

1. Should I see a different driver in the Device Driver window?
2. Any thoughts on how to get this to work?

As a side note, Linux shows the mouse as 2.0 but running at 1.1.While
I cannot expect them to support Linux, XP should work.

Thank you in advance for any suggestions.
Check your BIOS setup screen, in the USB section.
Some boards allow disabling USB2 in there.
For example, see

"USB EHCI Controller" [Enabled]

The fact you can get a port to operate
at USB 1.1, tells me there probably isn't a problem
with bus power on the port. So the wires themselves are
all likely working.

HTH,
Paul