If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1
pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer |
#2
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
Beemer wrote:
My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer My guess is, it'll work once the array is moved to 0..3 . The Spec Update and table "Intel ICH10 Corporate Device and Revision ID", hints at the separation of the ports. http://www.intel.com/Assets/PDF/specupdate/319974.pdf The datasheet, shows the SATA ports are split across two controllers. 0..3 are on one controller, 4..5 on another. I don't think Intel did a "programmer's guide" for this chip, at least I don't see one for download, so I'd have to guess at the symptoms to be expected. Since "soft RAID" is what a chip like this provides, at least for RAID purposes, all the ports should be equal. Whether the firmware/software chooses to run them that way, is purely a software design decision by somebody. http://www.intel.com/Assets/PDF/datasheet/319973.pdf Paul |
#3
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
I assume you created the raid array in the RAID BIOS as described in page 85
before you installed the OS? "Beemer" wrote in message ... My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer |
#4
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
"Paul" wrote in message ... Beemer wrote: My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer My guess is, it'll work once the array is moved to 0..3 . The Spec Update and table "Intel ICH10 Corporate Device and Revision ID", hints at the separation of the ports. http://www.intel.com/Assets/PDF/specupdate/319974.pdf The datasheet, shows the SATA ports are split across two controllers. 0..3 are on one controller, 4..5 on another. I don't think Intel did a "programmer's guide" for this chip, at least I don't see one for download, so I'd have to guess at the symptoms to be expected. Since "soft RAID" is what a chip like this provides, at least for RAID purposes, all the ports should be equal. Whether the firmware/software chooses to run them that way, is purely a software design decision by somebody. http://www.intel.com/Assets/PDF/datasheet/319973.pdf Paul Paul, Following you reply I moved the RAID pair from SATA ports 4-5 to 2-3. After setting RAID on and Port0-3 Native on I am disappointed that I am still getting BSOD with the Stop: 0x0000007B message. I am confused about whether I should have the Intel Matrix Storage Manager (MSM) software installed? Somehow I thought that on this GA EP45-DS3P motherboard this was already on a ROM? I have downloaded the MSM software from the Intel site but the release note shows that ICH10 is not listed only up to ICH9. When I try to load the software Iit fails with the message "This computer does not meet the minimum requirements for installing the software" My RAID pair has been initialised although the Cntrl-I menu although when RAID is switched off the two drives although active have not been partitioned? It should not be so difficult to set RAID up. I even made a fresh XP install and double checked when using F6 that the correct ICH10 RAID driver was selected regards, Beemer |
#5
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
Yes I made a fresh XP install and used the F6 to select the ICH10R Raid
driver regards, Beemer "Onsokumaru" wrote in message ... I assume you created the raid array in the RAID BIOS as described in page 85 before you installed the OS? "Beemer" wrote in message ... My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer |
#6
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
Beemer wrote:
"Paul" wrote in message ... Beemer wrote: My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer My guess is, it'll work once the array is moved to 0..3 . The Spec Update and table "Intel ICH10 Corporate Device and Revision ID", hints at the separation of the ports. http://www.intel.com/Assets/PDF/specupdate/319974.pdf The datasheet, shows the SATA ports are split across two controllers. 0..3 are on one controller, 4..5 on another. I don't think Intel did a "programmer's guide" for this chip, at least I don't see one for download, so I'd have to guess at the symptoms to be expected. Since "soft RAID" is what a chip like this provides, at least for RAID purposes, all the ports should be equal. Whether the firmware/software chooses to run them that way, is purely a software design decision by somebody. http://www.intel.com/Assets/PDF/datasheet/319973.pdf Paul Paul, Following you reply I moved the RAID pair from SATA ports 4-5 to 2-3. After setting RAID on and Port0-3 Native on I am disappointed that I am still getting BSOD with the Stop: 0x0000007B message. I am confused about whether I should have the Intel Matrix Storage Manager (MSM) software installed? Somehow I thought that on this GA EP45-DS3P motherboard this was already on a ROM? I have downloaded the MSM software from the Intel site but the release note shows that ICH10 is not listed only up to ICH9. When I try to load the software Iit fails with the message "This computer does not meet the minimum requirements for installing the software" My RAID pair has been initialised although the Cntrl-I menu although when RAID is switched off the two drives although active have not been partitioned? It should not be so difficult to set RAID up. I even made a fresh XP install and double checked when using F6 that the correct ICH10 RAID driver was selected regards, Beemer What driver did you install during the Windows install ? Did you F6 an AHCI driver ? Did you F6 a RAID driver ? If RAID is enabled, the RAID array was set up in the BIOS, Windows was installed, some driver was added via F6, this should be working. "RAID Management" exists in two places. On some motherboards, pressing Control-I brings you into the BIOS version of Intel RAID Management. If you set up a RAID mirror in there, then you might have to wait a few hours, for the data on one drive to be copied to the other (assuming an OS image was already present). If you install just one hard drive, install via F6 a RAID driver, boot into Windows with one drive, install the downloadable Intel RAID Management console, then you can control RAID from within Windows. After all that is done, shut down the computer and add the second drive. (At this point, no array exists). Boot into Windows again, and run the Intel RAID Management software. If you tell the software to set up a RAID 1 mirror, and the OS image obviously already exists, the software runs in the background, to make the two disks identical. The advantage of the Windows RAID Management console, is things can go on in the background. While using the BIOS method, may require doing it in the foreground (tying up the computer). (Depends on whether you need to initialize the array and have data copied from one drive to the other.) The README here mentions ICH10R. http://downloadmirror.intel.com/17059/eng/readme.txt That is from the download page at Intel, for 8.6.0.1007. http://downloadcenter.intel.com/filt...4&submit=Go%21 The driver and software works based on the enumeration of the hardware. For ICH10R, the enumeration numbers offered by the Southbridge, can be seen in the Spec Update document. What I do, is compare the numbers in the table, against the numbers in the INF for the floppy driver install. That may explain what is happening. (For example, what would happen if the driver didn't actually install, while the disks were on ports 4 and 5 ?) http://www.intel.com/Assets/PDF/specupdate/319974.pdf (page 9) Paul |
#7
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
In your initial message on Oct. 18, you had Windows XP on a non-raid
drive. Are you now trying to install XP on the raid drive and getting the boot error? On Sat, 1 Nov 2008 17:02:00 -0000, "Beemer" wrote: My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer |
#8
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
I mean you connect the drives, boot the PC, go past the system BIOS screen
to the RAID BIOS, CTRL+I to enter, create a RAID set. This is OS independant and needs no drivers. Then you install the OS. "Beemer" wrote in message ... Yes I made a fresh XP install and used the F6 to select the ICH10R Raid driver regards, Beemer "Onsokumaru" wrote in message ... I assume you created the raid array in the RAID BIOS as described in page 85 before you installed the OS? "Beemer" wrote in message ... My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer |
#9
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
Andy,
No the XP boot drive is not part of the Raid Beemer "andy" wrote in message ... In your initial message on Oct. 18, you had Windows XP on a non-raid drive. Are you now trying to install XP on the raid drive and getting the boot error? On Sat, 1 Nov 2008 17:02:00 -0000, "Beemer" wrote: My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer |
#10
|
|||
|
|||
SATA Port0-3 Native Mode and RAID problem
Yes I did this but I am now thingking that Paul might have a reason for it
to fail. I was using Sata ports 4 and 5 when I used F6 then Ctrl I anbd it failed. I then moved to ports 2-3 but Paul thinks that this might not be allowed after the drive is installed. regards, Beemer "Onsokumaru" wrote in message ... I mean you connect the drives, boot the PC, go past the system BIOS screen to the RAID BIOS, CTRL+I to enter, create a RAID set. This is OS independant and needs no drivers. Then you install the OS. "Beemer" wrote in message ... Yes I made a fresh XP install and used the F6 to select the ICH10R Raid driver regards, Beemer "Onsokumaru" wrote in message ... I assume you created the raid array in the RAID BIOS as described in page 85 before you installed the OS? "Beemer" wrote in message ... My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS setup page with SATA RAID/AHCI MOde = RAID SATA Port0-3 Native Mode = Enabled On booting I get the BSOD error Stop 0x0000007B ( etc) For some reason I do not understand F12 to enter boot menu doe not work with RAID enabled. I wanted to use this to check if (after enabling RAID) it is trying to boot from the wrong drive. Anyhow my question relates to SATA Port0-3 Native Mode. Why is only 0-3 mentioned and not 0-5? There is nothing in the manual to advise on this. Does it mean that the porfts 4-5 I have used for the RAID are in Legacy mode and this is why I cannot boot? One other thing I noticed is that when booting before the blue screen , the post screen shows "Serial ATA AHCI Bios ver iSrc 1.07 08042006", then I get a list of my six drives all of which are post screen marked as controlled by RAID driver Why then does it mention AHCI when I do not have AHCI selected in the bios? The RAID driver was loaded using F6 from a floppy with the files iaAHCI.cat iaAHCI.inf iaStor.cat iaStor.inf IaStor.sys license.txt TXTSETUP.OEM My next move is to try connecting the RAID to ports 2 and 3 but I will first wait to see if I get any response here. regards, Beemer |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
SATA Mode: RAID or IDE? | Kendall | Gigabyte Motherboards | 0 | March 29th 06 08:40 PM |
SATA 2 Native Command Cueing and Multi Tasking. Alot better ??? | Son Of Sheep. | Storage (alternative) | 4 | July 11th 05 10:21 AM |
SATA 2 Native Command Cueing and Multi Tasking. Alot better ??? | Son Of Sheep. | Overclocking | 5 | July 10th 05 12:31 PM |
P4G800-V Problem w/ 2 SATA drives at Ultra DMA Mode 5 | Greg | Asus Motherboards | 4 | January 19th 04 06:03 PM |
GA-7N400 Pro2 ITE RAID MODE 1 PROBLEM - Please help | Steve Peterson | Gigabyte Motherboards | 1 | December 20th 03 08:15 PM |