REQ Epson 1280 Technical/service Manual EPTM-SP1280 Epson says no longer avaiable

EP / Manuals for Printers - Technical
NO LONGER AVAILABLE EPTM-SP1280 In 5 to 7 Days New 0.00

On Wed, 10 Dec 2003 18:07:55 -0500, Sally wrote:

EP / Manuals for Printers - Technical
NO LONGER AVAILABLE EPTM-SP1280 In 5 to 7 Days New 0.00
What group would you like to see it posted in? But be prepared to be
disappointed, the "repair manual" is a joke unless you just need to
know how to remove assemblies. As I recall there are no schematics or
circuit-level troubleshooting included.

This group would be ok. I need to change the waste ink pads.

Thanks

On Wed, 10 Dec 2003 23:18:41 GMT, Matt wrote:

On Wed, 10 Dec 2003 18:07:55 -0500, Sally wrote:

EP / Manuals for Printers - Technical
NO LONGER AVAILABLE EPTM-SP1280 In 5 to 7 Days New 0.00
What group would you like to see it posted in? But be prepared to be
disappointed, the "repair manual" is a joke unless you just need to
know how to remove assemblies. As I recall there are no schematics or
circuit-level troubleshooting included.

Sally,
Here is the procedure to reset your "waste ink counter" on the Epson.
Maybe this is all you need to do for the moment if you're getting an
error message (extracted from the 1270 manual but should be
identical):

"To enter the Special Setting Mode, press Load/Eject button and
Cleaning button while turning on the printer. The Paper Out LED
starts blinking. While it is blinking (for 3 seconds), press the
specified button to activate the desirable setting mode.

NOTE: Special setting modes are not intended for users.

Special Setting Modes:

Load/Eject Switch - Resets EEPROM and timer IC.

Cleaning (Push for 10 sec) - Resets the ink overflow counter in
EEPROM."

So in other words just press the Load/Eject and Cleaning buttons while
you turn on the power, then release both buttons while the Paper Out
LED is flashing. Press and hold the cleaning button for at least 10
seconds.

Now, as to actually replacing the pad, these instructions (again, from
the 1270 manual) are in a zipped 270K file, and can't be posted to the
group here. However if you have an e-mail, I'd be happy to send it to
you.

-Matt






On Wed, 10 Dec 2003 20:47:42 -0500, Sally wrote:

This group would be ok. I need to change the waste ink pads.

Thanks

On Wed, 10 Dec 2003 23:18:41 GMT, Matt wrote:

On Wed, 10 Dec 2003 18:07:55 -0500, Sally wrote:

EP / Manuals for Printers - Technical
NO LONGER AVAILABLE EPTM-SP1280 In 5 to 7 Days New 0.00
What group would you like to see it posted in? But be prepared to be
disappointed, the "repair manual" is a joke unless you just need to
know how to remove assemblies. As I recall there are no schematics or
circuit-level troubleshooting included.

Thanks, I don't want to change them but the waste ink pads are FULL
and i have to do it.

please emal me hte man to



Thanks again, Your great!
Sally

On Thu, 11 Dec 2003 17:22:33 GMT, Matt wrote:

Sally,
Here is the procedure to reset your "waste ink counter" on the Epson.
Maybe this is all you need to do for the moment if you're getting an
error message (extracted from the 1270 manual but should be
identical):

"To enter the Special Setting Mode, press Load/Eject button and
Cleaning button while turning on the printer. The Paper Out LED
starts blinking. While it is blinking (for 3 seconds), press the
specified button to activate the desirable setting mode.

NOTE: Special setting modes are not intended for users.

Special Setting Modes:

Load/Eject Switch - Resets EEPROM and timer IC.

Cleaning (Push for 10 sec) - Resets the ink overflow counter in
EEPROM."

So in other words just press the Load/Eject and Cleaning buttons while
you turn on the power, then release both buttons while the Paper Out
LED is flashing. Press and hold the cleaning button for at least 10
seconds.

Now, as to actually replacing the pad, these instructions (again, from
the 1270 manual) are in a zipped 270K file, and can't be posted to the
group here. However if you have an e-mail, I'd be happy to send it to
you.

-Matt






On Wed, 10 Dec 2003 20:47:42 -0500, Sally wrote:

This group would be ok. I need to change the waste ink pads.

Thanks

On Wed, 10 Dec 2003 23:18:41 GMT, Matt wrote:

On Wed, 10 Dec 2003 18:07:55 -0500, Sally wrote:

EP / Manuals for Printers - Technical
NO LONGER AVAILABLE EPTM-SP1280 In 5 to 7 Days New 0.00
What group would you like to see it posted in? But be prepared to be
disappointed, the "repair manual" is a joke unless you just need to
know how to remove assemblies. As I recall there are no schematics or
circuit-level troubleshooting included.