If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Ancient History?? Looking for best 2xAGP vidcard for an old K6/MVP3 system (WTB possible)
Yup; I know "why bother"; but ....
(email reply is "ub*underscore*never" with the squirrely thingy between"yahoo dot com", no quotes or stars) It's still my prime machine; the o/c'ed "gamerbox" Barton K7N2L with the 9700Pro and the goodies is great-- but I still go back to this one for most real work . Specs on this box: Epox MVP3G2C w/1mb L2 (L3 with the K6/III +); 2X AGP at 3.3 volts. 512 mb PC100 SDRAM K6/III-450+ at 5x112 at 1.8vcc W98SE; current VIA 4in1 pack etc. It's rock-solid with this minor overclock (remember it's a {+} laptop K6 !), the limit is the 2940 SCSI card. The Epox has the "good AGP power", Present vidcard is an ATI RagePro 128 w/16 megs. I'd like to bump it up to 'best bang for buck" . I'd like to go with at least 64 megs for some gaming; but I know I'm not going to do HL2 on this beast g . I've had a 32m TNT2 Ultra in this machine once; looked great but the hasslefactor of getting a TNT2 to work on a VIA MVP board is not nice, and it gets worse when you try to update drivers. When it worked; it would run Serious Sam but not at max! I've been away from the "vidcard wars" for a while; missed a lot of the info . I've been googling both the web and newsgroups; looks like it's possible to go up to a decent low(now) end card in either ATI or NVidia flavors. I just have to make sure the card's 2X/3.3 volt. ATI--looks like I can go up to a 2x/4x rated version of the 9200 or lower version. Nvidia -- Same ; possibly up to a TI 4600 or lower. Anybody have any "good history" on similar vidcards on an MVP3 mobo ?? I'm also interested in buying; if you've got one sitting around.. |
#2
|
|||
|
|||
"R. Asby Dragon" wrote in message ... Yup; I know "why bother"; but .... (email reply is "ub*underscore*never" with the squirrely thingy between"yahoo dot com", no quotes or stars) It's still my prime machine; the o/c'ed "gamerbox" Barton K7N2L with the 9700Pro and the goodies is great-- but I still go back to this one for most real work . Specs on this box: Epox MVP3G2C w/1mb L2 (L3 with the K6/III +); 2X AGP at 3.3 volts. 512 mb PC100 SDRAM K6/III-450+ at 5x112 at 1.8vcc W98SE; current VIA 4in1 pack etc. It's rock-solid with this minor overclock (remember it's a {+} laptop K6 !), the limit is the 2940 SCSI card. The Epox has the "good AGP power", Present vidcard is an ATI RagePro 128 w/16 megs. I'd like to bump it up to 'best bang for buck" . I'd like to go with at least 64 megs for some gaming; but I know I'm not going to do HL2 on this beast g . I've had a 32m TNT2 Ultra in this machine once; looked great but the hasslefactor of getting a TNT2 to work on a VIA MVP board is not nice, and it gets worse when you try to update drivers. When it worked; it would run Serious Sam but not at max! I've been away from the "vidcard wars" for a while; missed a lot of the info . I've been googling both the web and newsgroups; looks like it's possible to go up to a decent low(now) end card in either ATI or NVidia flavors. I just have to make sure the card's 2X/3.3 volt. ATI--looks like I can go up to a 2x/4x rated version of the 9200 or lower version. Nvidia -- Same ; possibly up to a TI 4600 or lower. Anybody have any "good history" on similar vidcards on an MVP3 mobo ?? I'm also interested in buying; if you've got one sitting around.. A gf2 ultra sound like your cuppa tea, or a gf4mx440 look on ebay chris |
#3
|
|||
|
|||
On Sun, 8 Feb 2004 14:23:46 -0800, "R. Asby Dragon"
wrote: Yup; I know "why bother"; but .... (email reply is "ub*underscore*never" with the squirrely thingy between"yahoo dot com", no quotes or stars) It's still my prime machine; the o/c'ed "gamerbox" Barton K7N2L with the 9700Pro and the goodies is great-- but I still go back to this one for most real work . Specs on this box: Epox MVP3G2C w/1mb L2 (L3 with the K6/III +); 2X AGP at 3.3 volts. 512 mb PC100 SDRAM K6/III-450+ at 5x112 at 1.8vcc W98SE; current VIA 4in1 pack etc. Why bother...? -- Remember when real men used Real computers!? When 512K of video RAM was a lot! Death to Palladium & WPA!! |
#4
|
|||
|
|||
Apart from "why bother?", I'd suggest either Radeon7500 OR Gf2pro/ultra.
Both with 64megs. Go with the cheapest you find of them. Don't think about ti4200. With this cpu, you won't use the power of gf4, heck you'd be lucky to even fully use power of gf2 ultra or r7500. "R. Asby Dragon" wrote in message ... Yup; I know "why bother"; but .... (email reply is "ub*underscore*never" with the squirrely thingy between"yahoo dot com", no quotes or stars) It's still my prime machine; the o/c'ed "gamerbox" Barton K7N2L with the 9700Pro and the goodies is great-- but I still go back to this one for most real work . Specs on this box: Epox MVP3G2C w/1mb L2 (L3 with the K6/III +); 2X AGP at 3.3 volts. 512 mb PC100 SDRAM K6/III-450+ at 5x112 at 1.8vcc W98SE; current VIA 4in1 pack etc. It's rock-solid with this minor overclock (remember it's a {+} laptop K6 !), the limit is the 2940 SCSI card. The Epox has the "good AGP power", Present vidcard is an ATI RagePro 128 w/16 megs. I'd like to bump it up to 'best bang for buck" . I'd like to go with at least 64 megs for some gaming; but I know I'm not going to do HL2 on this beast g . I've had a 32m TNT2 Ultra in this machine once; looked great but the hasslefactor of getting a TNT2 to work on a VIA MVP board is not nice, and it gets worse when you try to update drivers. When it worked; it would run Serious Sam but not at max! I've been away from the "vidcard wars" for a while; missed a lot of the info . I've been googling both the web and newsgroups; looks like it's possible to go up to a decent low(now) end card in either ATI or NVidia flavors. I just have to make sure the card's 2X/3.3 volt. ATI--looks like I can go up to a 2x/4x rated version of the 9200 or lower version. Nvidia -- Same ; possibly up to a TI 4600 or lower. Anybody have any "good history" on similar vidcards on an MVP3 mobo ?? I'm also interested in buying; if you've got one sitting around.. |
#5
|
|||
|
|||
I chucked a old Gforce 2 MX400 in a mates PII 350 and it runs quake 3 not
too badly at all. I dunno if going to an ultra gf2 is going to help you any with such a low processor. For him , it was worth bothering about. The card was collecting dust in my box of bits , and now he has some 3d acceleration to play a fair few games that are old and cheap to buy. B. |
#6
|
|||
|
|||
ATI 9100, it is a little bit faster then a 9200
starts at $53 on www.pricewatch.com Remember you need to reload the VIA drivers after every hardware change. "R. Asby Dragon" wrote in message ... Yup; I know "why bother"; but .... (email reply is "ub*underscore*never" with the squirrely thingy between"yahoo dot com", no quotes or stars) It's still my prime machine; the o/c'ed "gamerbox" Barton K7N2L with the 9700Pro and the goodies is great-- but I still go back to this one for most real work . Specs on this box: Epox MVP3G2C w/1mb L2 (L3 with the K6/III +); 2X AGP at 3.3 volts. 512 mb PC100 SDRAM K6/III-450+ at 5x112 at 1.8vcc W98SE; current VIA 4in1 pack etc. It's rock-solid with this minor overclock (remember it's a {+} laptop K6 !), the limit is the 2940 SCSI card. The Epox has the "good AGP power", Present vidcard is an ATI RagePro 128 w/16 megs. I'd like to bump it up to 'best bang for buck" . I'd like to go with at least 64 megs for some gaming; but I know I'm not going to do HL2 on this beast g . I've had a 32m TNT2 Ultra in this machine once; looked great but the hasslefactor of getting a TNT2 to work on a VIA MVP board is not nice, and it gets worse when you try to update drivers. When it worked; it would run Serious Sam but not at max! I've been away from the "vidcard wars" for a while; missed a lot of the info . I've been googling both the web and newsgroups; looks like it's possible to go up to a decent low(now) end card in either ATI or NVidia flavors. I just have to make sure the card's 2X/3.3 volt. ATI--looks like I can go up to a 2x/4x rated version of the 9200 or lower version. Nvidia -- Same ; possibly up to a TI 4600 or lower. Anybody have any "good history" on similar vidcards on an MVP3 mobo ?? I'm also interested in buying; if you've got one sitting around.. |
#7
|
|||
|
|||
For a cheap performance upgrade.
Get a used Abit KT7, you can use your current PC100 memory and a CPU up to 1.4ghz "R. Asby Dragon" wrote in message ... Yup; I know "why bother"; but .... (email reply is "ub*underscore*never" with the squirrely thingy between"yahoo dot com", no quotes or stars) It's still my prime machine; the o/c'ed "gamerbox" Barton K7N2L with the 9700Pro and the goodies is great-- but I still go back to this one for most real work . Specs on this box: Epox MVP3G2C w/1mb L2 (L3 with the K6/III +); 2X AGP at 3.3 volts. 512 mb PC100 SDRAM K6/III-450+ at 5x112 at 1.8vcc W98SE; current VIA 4in1 pack etc. It's rock-solid with this minor overclock (remember it's a {+} laptop K6 !), the limit is the 2940 SCSI card. The Epox has the "good AGP power", Present vidcard is an ATI RagePro 128 w/16 megs. I'd like to bump it up to 'best bang for buck" . I'd like to go with at least 64 megs for some gaming; but I know I'm not going to do HL2 on this beast g . I've had a 32m TNT2 Ultra in this machine once; looked great but the hasslefactor of getting a TNT2 to work on a VIA MVP board is not nice, and it gets worse when you try to update drivers. When it worked; it would run Serious Sam but not at max! I've been away from the "vidcard wars" for a while; missed a lot of the info . I've been googling both the web and newsgroups; looks like it's possible to go up to a decent low(now) end card in either ATI or NVidia flavors. I just have to make sure the card's 2X/3.3 volt. ATI--looks like I can go up to a 2x/4x rated version of the 9200 or lower version. Nvidia -- Same ; possibly up to a TI 4600 or lower. Anybody have any "good history" on similar vidcards on an MVP3 mobo ?? I'm also interested in buying; if you've got one sitting around.. |
#8
|
|||
|
|||
I'm not adverse to replying to my own posts; here's one.
I've read all the relevant replies on Usenet; did a bunch more googling ; got some personal replies, also went on "local scrounge" After wading thru the ATI vs NVIDIA rants; the "why bother" mendicants; and the "real honest" replies (and I appreciate those) ; I went Ebaying and found some deals. 1) Radeon 7500 64meg DDR for $33; on the way now 2) Radeon 9000 128meg DDR for $43 - pending Personal offers-- lots of GF3 440MX's-- even one supposedly 128 megs; an 8500 AIW with tuner probs for free; even a dual Gproc Voodo 5 . I even found a Radeon 7000 64meg SDR AGP in my 'pile o'crap' that I'd forgotten ... It all boils down to "making the best of what you have"; I'm not just doing my own machines-- I'm doing "Free IT" for friends and family spreading from 486s to high-end boxes . I'm juggling parts all the time; "A" wants a new vidcard as in ATI 9800 range; I'll find "A" a deal; move his old vidcard to someone else "B" -- I think you understand. In my case with the K6/III-(+) ; it's like "old hot rods" ; I did that. I've done the old '59a' Flathead Ford V8; early small-block Chevys; 63 1/2 Ford Galaxy H/T with a "medium riser" 427 ; et al. I'll keep it running as long as "it does what I want it to do" |
#9
|
|||
|
|||
I'd look for the last generation of 3dfx cards, like a 5500...especially if
you do any OpenGL stuff. Just make sure it will fit in your case "R. Asby Dragon" wrote in message ... Yup; I know "why bother"; but .... (email reply is "ub*underscore*never" with the squirrely thingy between"yahoo dot com", no quotes or stars) It's still my prime machine; the o/c'ed "gamerbox" Barton K7N2L with the 9700Pro and the goodies is great-- but I still go back to this one for most real work . Specs on this box: Epox MVP3G2C w/1mb L2 (L3 with the K6/III +); 2X AGP at 3.3 volts. 512 mb PC100 SDRAM K6/III-450+ at 5x112 at 1.8vcc W98SE; current VIA 4in1 pack etc. It's rock-solid with this minor overclock (remember it's a {+} laptop K6 !), the limit is the 2940 SCSI card. The Epox has the "good AGP power", Present vidcard is an ATI RagePro 128 w/16 megs. I'd like to bump it up to 'best bang for buck" . I'd like to go with at least 64 megs for some gaming; but I know I'm not going to do HL2 on this beast g . I've had a 32m TNT2 Ultra in this machine once; looked great but the hasslefactor of getting a TNT2 to work on a VIA MVP board is not nice, and it gets worse when you try to update drivers. When it worked; it would run Serious Sam but not at max! I've been away from the "vidcard wars" for a while; missed a lot of the info . I've been googling both the web and newsgroups; looks like it's possible to go up to a decent low(now) end card in either ATI or NVidia flavors. I just have to make sure the card's 2X/3.3 volt. ATI--looks like I can go up to a 2x/4x rated version of the 9200 or lower version. Nvidia -- Same ; possibly up to a TI 4600 or lower. Anybody have any "good history" on similar vidcards on an MVP3 mobo ?? I'm also interested in buying; if you've got one sitting around.. |
#10
|
|||
|
|||
Yeah, but those cards have driver issues, not to mension lack of support. I
visited 3dfx.products.voodoo5, a couple of days ago, and what a sad sight. Nothing but spam and a few lonely posts. That board used to be full of usefull posts a few years ago. So my point is: Get a card that has good support/drivers. I think for 450+cpu, a radeon7000 or GF2 class (not mx)card is more than enough. Even if cpu is oc'ed, it should hold up. "rna" wrote in message news:j31Wb.16305$QA2.62347@attbi_s52... I'd look for the last generation of 3dfx cards, like a 5500...especially if you do any OpenGL stuff. Just make sure it will fit in your case "R. Asby Dragon" wrote in message ... Yup; I know "why bother"; but .... (email reply is "ub*underscore*never" with the squirrely thingy between"yahoo dot com", no quotes or stars) It's still my prime machine; the o/c'ed "gamerbox" Barton K7N2L with the 9700Pro and the goodies is great-- but I still go back to this one for most real work . Specs on this box: Epox MVP3G2C w/1mb L2 (L3 with the K6/III +); 2X AGP at 3.3 volts. 512 mb PC100 SDRAM K6/III-450+ at 5x112 at 1.8vcc W98SE; current VIA 4in1 pack etc. It's rock-solid with this minor overclock (remember it's a {+} laptop K6 !), the limit is the 2940 SCSI card. The Epox has the "good AGP power", Present vidcard is an ATI RagePro 128 w/16 megs. I'd like to bump it up to 'best bang for buck" . I'd like to go with at least 64 megs for some gaming; but I know I'm not going to do HL2 on this beast g . I've had a 32m TNT2 Ultra in this machine once; looked great but the hasslefactor of getting a TNT2 to work on a VIA MVP board is not nice, and it gets worse when you try to update drivers. When it worked; it would run Serious Sam but not at max! I've been away from the "vidcard wars" for a while; missed a lot of the info . I've been googling both the web and newsgroups; looks like it's possible to go up to a decent low(now) end card in either ATI or NVidia flavors. I just have to make sure the card's 2X/3.3 volt. ATI--looks like I can go up to a 2x/4x rated version of the 9200 or lower version. Nvidia -- Same ; possibly up to a TI 4600 or lower. Anybody have any "good history" on similar vidcards on an MVP3 mobo ?? I'm also interested in buying; if you've got one sitting around.. |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ancient History?? Looking for best 2xAGP vidcard for an old K6/MVP3 system (WTB possible) | R. Asby Dragon | Ati Videocards | 12 | February 11th 04 10:22 AM |
Ancient History?? Looking for best 2xAGP vidcard for an old K6/MVP3 system (WTB possible) | R. Asby Dragon | Homebuilt PC's | 11 | February 10th 04 10:24 PM |
Ancient history ? P5A and K6/2/III (+) chips any luck ? | R. Asby Dragon | Asus Motherboards | 4 | November 6th 03 12:54 AM |