If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Probs MSA1000, "I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed"
Hi,
we have a problem with a HP MSA1000. We start to install the MSA1000, but when conntecting to to CLI we got the following errors the whole time. Maybe somebody can help us ? Do somebody know the meaning of the error (we haven't found it any hp-manuel) Do somebody know a way to track down this problem ? Thanks for helping regards Danny Starting ICL links and beginning redundancy negotiation. PCI ICL link has been enabled. Starting ICL negotiation . . . NVRAM Contents: backplane: checksum offset = 118 iteration offset = 121 chassis name = VJ world wide name = 500805F3000005C0 chassis serial num = 9J140000L2GJ backplane serial num = P3442XAH9HX268 factory: board serial num = P56350B9IMX0B9 Startup complete. * MSA1000 Command Line Interface * CLI I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 3 I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 2 I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 1 setupICL_Link: failed to receive serial ICL info message. setupRedundancy: failed to negotiate redundancy. Redundant controller has been killed. I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 3 I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 2 I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 1 I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 0 I2C_Read: Device = EMU, I2C_Read_Chunk() failed. ERROR: failed on do_i2c_emu_command(). ------------------------------------------------------------ DT Netsolution GmbH - Talaeckerstr. 30 - D-70437 Stuttgart Tel: +49-711-849910-32 Fax: +49-711-849910-932 WEB: http://www.dtnet.de/ email: |
#2
|
|||
|
|||
"Daniel Schwager" wrote in message
... Hi, we have a problem with a HP MSA1000. We start to install the MSA1000, but when conntecting to to CLI we got the following errors the whole time. Maybe somebody can help us ? Do somebody know the meaning of the error (we haven't found it any hp-manuel) Do somebody know a way to track down this problem ? Thanks for helping regards Danny * MSA1000 Command Line Interface * CLI I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 3 I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 2 I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed. I2C_Read: Resetting I2C bus for device = EMU, retry = 1 setupICL_Link: failed to receive serial ICL info message. setupRedundancy: failed to negotiate redundancy. Redundant controller has been killed. I2C is a serial protocol inside the machine between chips and subsystems internally. The message probably means that the internal subsystems can no longer talk to eachother. That's most likely a hardware failure, so get HP to service it. Rob |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
pc problems after g card upgrade + sp2 | ben reed | Homebuilt PC's | 9 | November 30th 04 01:04 AM |
Asus A7N8X-X and AMD Athlon XP 3200+ | Information Scavenger | Asus Motherboards | 30 | November 9th 04 09:30 PM |
Update on Athlon 2600 Ghz discrepancy | David Simmons | Overclocking AMD Processors | 7 | August 27th 04 08:56 PM |
íostat with tapes and disks | Rick Denoire | Storage & Hardrives | 0 | July 29th 04 10:51 PM |
my new mobo o/c's great | rockerrock | Overclocking AMD Processors | 9 | June 30th 04 08:17 PM |