If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
PSU problems with motherboard
I built a system a couple of months ago with an MSI 865PE Neo2-FIS2R
motherboard and an Antec TrueBlue 480W PSU. The system would turn on, but it would never boot up at all. The Neo2's four diagnostic LED lights all hung on solid red, indicating that the processor was damaged. However, the processor (a P4 2.8GHz CPU) was not damaged. I eventually went to CompUSA and bought one of their store-brand 300W PSUs, installed it in place of the Antec PSU, and sure enough the system then booted up and worked like a charm. (I didn't have many components installed anyway, so a 300W PSU was sufficient anyway.) I presumed the Antec's PSU power cable was bad, and got a refund on the unit. (I had purchased by mail order from a retailer in another part of the country.) Since then, I hadn't had any problems with the system. Except that on three or four occasions, when I turned on the PC, it would power on but not boot up. I simply turned it off and back on again, and the next time it booted up properly. I wasn't too worried about this since I intended to eventually upgrade the PSU. Then, last Wednesday, I attempted to install SP2 for Windows XP. (WinXP is the only OS installed on the system). The installation of SP2 seemed successful, except that when I rebooted, WinXP stayed stuck on the bootup screen with the Windows logo and black background. Only one block of the progress bar would appear at the bottom, and it would stay stuck on that one block without any sign of activity. Doing a hard shutdown and booting back up again got the same result. So I let Windows stay on that screen overnight, thinking maybe it needed a long time to boot up the first time after installing SP2. The next morning, it was still stuck on that same screen with only one block of the progress bar, so I did another hard shutdown. I had a .GHO file of WinXP on a storage partition, and I decided it was time to restore the ghost image of XP (pre-SP2 install attempt). However, when I booted into the Ghost 2003 diskette, it would always get stuck while loading the GUI, just as WinXP always got stuck while loading. I shut down the PC and started it back up again and retried loading Ghost a few times, but it kept freezing while loading the GUI. Even though WinXP and Ghost always froze while loading, I could boot into the Neo2's BIOS and never have any problems with it. All the BIOS's setting (including the power levels) were normal. Then it got to the point that holding down the PC's power button would not force a hard shutdown, so I had to remove the power cord from the back of the PC to do this. And as soon as I plugged the power cord back in, the PC started up on its own automatically without me hitting the button. I unplugged everything from the system a let it set and "cool down" overnight, but when I plugged in the power cord the next morning, the exact same thing happened again. Since the generic 300W PSU was apparently not working properly, I went back to CompUSA today and bought another Antec TrueBlue 480W PSU, since I needed a new PSU and this was the one that I had wanted in the first place. However, after I installed the Antec PSU and powered on the system, the exact same thing happened that had happened with the other one befo the PC would power on, but the system never booted up at all. Just like before, the Neo2's four diagnostic LED lights all hung on solid red. I did a Google search but found no issues with the the Antec TrueBlue and the MSI 865PE Neo2. (And keep in mind that the other Antec TrueBlue was bought in another part of the country, so it's doubtful that the two would be from a same "bad batch".) I found that if I reconnected the generic CompUSA-brand 300W PSU back to the motherboard, it would boot up, but the OS would still always get stuck. Then I set the Antec PSU's switch from 115 to 230, connected it to the Neo2, turned it on ... and everything was dead. When that happened, I unplugged the Antec immediately. I don't think I had it powered on at 230 for more than five seconds, but now when I try to power on the Neo2, even with the generic CompUSA PSU reconnected back to it, it stays dead. So I guess I fried it. (I thought the 115/230 selector was for the input power only and wouldn't have any affect on the PSU's output to the mobo.) So why will my Neo2 mobo not boot up with a PSU as reputable as the Antec TrueBlue 480W? (I've verified that my Antec PSU works fine on other systems.) Can a bad power supply (the generic 300w PSU) cause an OS to freeze up during boot, but cause no other apparent problems? Is there a certain amount of time I can wait to see if the motherboard will boot up again? Or is it fried for sure? I've been having all kinds of crazy stuff going on since the start, and this experience has been hellish to say the least. I'm just trying to get a handle on what's going on. TIA |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Athlon XP Mobile Question - What motherboard? | Post Replies Here Please | Overclocking AMD Processors | 9 | August 16th 04 12:33 AM |
Chip fan doesn't run on Gigabyte GA-7N400 Pro2 motherboard | Luke | General | 13 | February 8th 04 12:12 AM |
MSI K7 motherboard problems | Peter Werner | General | 1 | January 22nd 04 02:42 PM |
AOPEN AX4BS-V MOTHERBOARD - won't boot - won't POST - help please!! | lucy | Homebuilt PC's | 3 | November 29th 03 05:21 AM |
Major Computer Problems | Toronto Garage Door Company | General | 20 | November 13th 03 09:41 PM |