If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
primary master hard disk fail
Hy,
getting this error message "primary master hard disk fail"; after booting an ibm hard disk with a "maxtor draco" macintosh disk. Award Plug&Play Bios says: 1st screen Detecting IDE Primary Master...... IC35L060AVER07-0 Detecting IDE Primary Slave...... Maxtor Draco Detecting IDE Secondary Master.......CR-48XATE Detecting IDE Secondary Slave......None 2nd screen Prim. Master Disk: None Primary Slave Disk: None Secondary Master Disk: CR-48XATE Secondary Slave Disk: None Diagnostics with Powermax displays error-codes: UKOE02, S57, BiosExtensionSupport - failed, Partition information - read fail. MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive Fitness Test does it, but could not handle the MacIntosh hard disk. Anyone has an idea what to do? Are there other diagnostics tools for windows which can handle Mac hard disks? Any help would be appreciated. Thanks in advance Regards, berthold Some additional details: serial, model/GTLA: S/N K80FEMVC 54098U8 Motherboard, chip Medion MD9901, MicroATX Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache Intel ZX, Intel PIIX4E Powermax-Diagnostics Error-Codes: UKOE02, S57, BiosExtensionSupport - failed Partition information - read fail |
#2
|
|||
|
|||
berthold wrote:
Hy, getting this error message "primary master hard disk fail"; after booting an ibm hard disk with a "maxtor draco" macintosh disk. Award Plug&Play Bios says: 1st screen Detecting IDE Primary Master...... IC35L060AVER07-0 Detecting IDE Primary Slave...... Maxtor Draco Detecting IDE Secondary Master.......CR-48XATE Detecting IDE Secondary Slave......None 2nd screen Prim. Master Disk: None Primary Slave Disk: None Secondary Master Disk: CR-48XATE Secondary Slave Disk: None Diagnostics with Powermax displays error-codes: UKOE02, S57, BiosExtensionSupport - failed, Partition information - read fail. MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive Fitness Test does it, but could not handle the MacIntosh hard disk. Anyone has an idea what to do? Are there other diagnostics tools for windows which can handle Mac hard disks? Any help would be appreciated. Thanks in advance Regards, berthold Some additional details: serial, model/GTLA: S/N K80FEMVC 54098U8 Motherboard, chip Medion MD9901, MicroATX Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache Intel ZX, Intel PIIX4E Powermax-Diagnostics Error-Codes: UKOE02, S57, BiosExtensionSupport - failed Partition information - read fail Swap primary/secondary IDE cables at mobo end and let us know what it says. Might be IDE controller dead/failing. Alan |
#3
|
|||
|
|||
"berthold" wrote in message om...
Hi, getting this error message "primary master hard disk fail"; after booting an ibm hard disk with a "maxtor draco" macintosh disk. Award Plug&Play Bios says: 1st screen Detecting IDE Primary Master...... IC35L060AVER07-0 Detecting IDE Primary Slave...... Maxtor Draco "Maxtor Draco" means that it is either dead or not set to spin-up auto. Since the IBM cannot be read either the Maxtor is likely dead. Detecting IDE Secondary Master.......CR-48XATE Detecting IDE Secondary Slave......None 2nd screen Prim. Master Disk: None Primary Slave Disk: None Secondary Master Disk: CR-48XATE Secondary Slave Disk: None Diagnostics with Powermax displays error-codes: UKOE02, S57, BiosExtensionSupport - failed, Partition information - read fail. MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive Fitness Test does it, but could not handle the MacIntosh hard disk. Anyone has an idea what to do? Are there other diagnostics tools for windows which can handle Mac hard disks? Put the Maxtor alone on its own cable, see what changes. Any help would be appreciated. Thanks in advance Regards, berthold Some additional details: serial, model/GTLA: S/N K80FEMVC 54098U8 Motherboard, chip Medion MD9901, MicroATX Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache Intel ZX, Intel PIIX4E Powermax-Diagnostics Error-Codes: UKOE02, S57, BiosExtensionSupport - failed Partition information - read fail |
#4
|
|||
|
|||
tried a lot of things.
used the maxtor drive as: primary master single and slave Secondary master single and slave even swapped the IDE cables on the motherboard. Checked and changed always the jumpers. But getting "...hard disk fail". Bios recognizes as "Maxtor Draco" and the IBMs drive as "IC06035AVER07" New details from IBMs Drive Fitness Test on Maxtor's Draco says: Primary Master/Slave Maxtor Draco 10,25 GB (although it's a 40,9 GB hdd) ATA-5 Cache 2097 KB Ultra DMA: Highest Mode: 4, Active Mode: None Write Cache: enabled read look-ahead: enabled S.m.a.r.t. options: disabled security feature not swapped regards, berthold "Folkert Rienstra" wrote in message ... "berthold" wrote in message om... Hi, getting this error message "primary master hard disk fail"; after booting an ibm hard disk with a "maxtor draco" macintosh disk. Award Plug&Play Bios says: 1st screen Detecting IDE Primary Master...... IC35L060AVER07-0 Detecting IDE Primary Slave...... Maxtor Draco "Maxtor Draco" means that it is either dead or not set to spin-up auto. Since the IBM cannot be read either the Maxtor is likely dead. Detecting IDE Secondary Master.......CR-48XATE Detecting IDE Secondary Slave......None 2nd screen Prim. Master Disk: None Primary Slave Disk: None Secondary Master Disk: CR-48XATE Secondary Slave Disk: None Diagnostics with Powermax displays error-codes: UKOE02, S57, BiosExtensionSupport - failed, Partition information - read fail. MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive Fitness Test does it, but could not handle the MacIntosh hard disk. Anyone has an idea what to do? Are there other diagnostics tools for windows which can handle Mac hard disks? Put the Maxtor alone on its own cable, see what changes. Any help would be appreciated. Thanks in advance Regards, berthold Some additional details: serial, model/GTLA: S/N K80FEMVC 54098U8 Motherboard, chip Medion MD9901, MicroATX Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache Intel ZX, Intel PIIX4E Powermax-Diagnostics Error-Codes: UKOE02, S57, BiosExtensionSupport - failed Partition information - read fail |
#5
|
|||
|
|||
"berthold" wrote in message om...
tried a lot of things. used the maxtor drive as: primary master single and slave Secondary master single and slave even swapped the IDE cables on the motherboard. Checked and changed always the jumpers. But getting "...hard disk fail". Bios recognizes as "Maxtor Draco" So it's dead. and the IBMs drive as "IC06035AVER07" New details from IBMs Drive Fitness Test on Maxtor's Draco says: Primary Master/Slave Maxtor Draco 10,25 GB (although it's a 40,9 GB hdd) Probably the smallest size in the Draco series design. The actual size is read from the platters once it has spun-up. ATA-5 Cache 2097 KB Ultra DMA: Highest Mode: 4, Active Mode: None Write Cache: enabled read look-ahead: enabled S.m.a.r.t. options: disabled security feature not swapped regards, berthold "Folkert Rienstra" wrote in message ... "berthold" wrote in message om... Hi, getting this error message "primary master hard disk fail"; after booting an ibm hard disk with a "maxtor draco" macintosh disk. Award Plug&Play Bios says: 1st screen Detecting IDE Primary Master...... IC35L060AVER07-0 Detecting IDE Primary Slave...... Maxtor Draco "Maxtor Draco" means that it is either dead or not set to spin-up auto. Since the IBM cannot be read either the Maxtor is likely dead. Detecting IDE Secondary Master.......CR-48XATE Detecting IDE Secondary Slave......None 2nd screen Prim. Master Disk: None Primary Slave Disk: None Secondary Master Disk: CR-48XATE Secondary Slave Disk: None Diagnostics with Powermax displays error-codes: UKOE02, S57, BiosExtensionSupport - failed, Partition information - read fail. MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive Fitness Test does it, but could not handle the MacIntosh hard disk. Anyone has an idea what to do? Are there other diagnostics tools for windows which can handle Mac hard disks? Put the Maxtor alone on its own cable, see what changes. Any help would be appreciated. Thanks in advance Regards, berthold Some additional details: serial, model/GTLA: S/N K80FEMVC 54098U8 Motherboard, chip Medion MD9901, MicroATX Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache Intel ZX, Intel PIIX4E Powermax-Diagnostics Error-Codes: UKOE02, S57, BiosExtensionSupport - failed Partition information - read fail |
#6
|
|||
|
|||
berthold wrote:
tried a lot of things. They make decent doorstops. used the maxtor drive as: primary master single and slave Secondary master single and slave even swapped the IDE cables on the motherboard. Checked and changed always the jumpers. But getting "...hard disk fail". Bios recognizes as "Maxtor Draco" and the IBMs drive as "IC06035AVER07" New details from IBMs Drive Fitness Test on Maxtor's Draco says: Primary Master/Slave Maxtor Draco 10,25 GB (although it's a 40,9 GB hdd) ATA-5 Cache 2097 KB Ultra DMA: Highest Mode: 4, Active Mode: None Write Cache: enabled read look-ahead: enabled S.m.a.r.t. options: disabled security feature not swapped regards, berthold "Folkert Rienstra" wrote in message ... "berthold" wrote in message om... Hi, getting this error message "primary master hard disk fail"; after booting an ibm hard disk with a "maxtor draco" macintosh disk. Award Plug&Play Bios says: 1st screen Detecting IDE Primary Master...... IC35L060AVER07-0 Detecting IDE Primary Slave...... Maxtor Draco "Maxtor Draco" means that it is either dead or not set to spin-up auto. Since the IBM cannot be read either the Maxtor is likely dead. Detecting IDE Secondary Master.......CR-48XATE Detecting IDE Secondary Slave......None 2nd screen Prim. Master Disk: None Primary Slave Disk: None Secondary Master Disk: CR-48XATE Secondary Slave Disk: None Diagnostics with Powermax displays error-codes: UKOE02, S57, BiosExtensionSupport - failed, Partition information - read fail. MaxBlast III does not recognize the Maxtor Hard Disk, IBMs Drive Fitness Test does it, but could not handle the MacIntosh hard disk. Anyone has an idea what to do? Are there other diagnostics tools for windows which can handle Mac hard disks? Put the Maxtor alone on its own cable, see what changes. Any help would be appreciated. Thanks in advance Regards, berthold Some additional details: serial, model/GTLA: S/N K80FEMVC 54098U8 Motherboard, chip Medion MD9901, MicroATX Intel Pentium III, 100 MHz Host-Bustaktrate, 512KB Cache Intel ZX, Intel PIIX4E Powermax-Diagnostics Error-Codes: UKOE02, S57, BiosExtensionSupport - failed Partition information - read fail -- The e-mail address in our reply-to line is reversed in an attempt to minimize spam. Our true address is of the form . |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Newbie: OC Advice: AMDXP2200 CPU | Donald Bock | Overclocking AMD Processors | 2 | March 12th 05 01:14 AM |
Primary Hard Disk Drive 1 Not Found | brandon | General Hardware | 5 | July 18th 04 11:39 PM |
RAID card for my PC?? | TANKIE | General | 5 | May 22nd 04 01:09 AM |
SOLUTION! IBM Hard Drive only recognized as 33GB hard drive, but is more >>>82.3GB | Andy | Storage (alternative) | 9 | November 18th 03 12:20 AM |
set CDROM as master not slave? | kony | General | 1 | June 28th 03 07:40 AM |