A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » Motherboards » Asus Motherboards
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Zalman ZM-50HP VGA Heatsink & P4P800 Deluxe



 
 
Thread Tools Display Modes
  #1  
Old June 25th 03, 08:55 AM
John Smith
external usenet poster
 
Posts: n/a
Default Zalman ZM-50HP VGA Heatsink & P4P800 Deluxe

Ron,

I had it working for, my PC that is, 6 hours non-stop last night and the
ZM-50HP eventually got warm to touch on the front. I think, to be frank,
that my Geforce 4460MX card does not generate that much heat. Zalman
themselves describe it as a low-heat card.

(I personally think anyone who has the P4P800 and who hates noise with VGA
cards would have to now only buy VGA cards with built-in heatsinks and not
fans as there is no way the bigger Zalman VGA heatsinks will fit.)

Yes, it is all fitted correctly with the heatpipe on the right way, at the
right angle, etc.

With hindsight, yes, it is quieter. I suppose I was expecting 'instant
peace' but the fan on that VGA card used to drive me nuts on my last PC. If
I had installed it along with the Zalman CPU cooler at the same time I
probably would have been posting about how wonderfully silent my PC has
gone.

The VGA heatsink has made a difference as, prior to installing it, if I
momentarilly stopped my CPU fan I still could hear an awful lot of noise and
could not tell whether it was the VGA fan, the case fan or the PSU fan.
After installing the VGA heatsink I, late last night, momentarilly stopped
my CPU fan and, voila, there was silence! I was amazed.

So, the next thing now is to get one of those Zalman CPU 7000-alcu coolers.

J.


"Ron Miller" wrote in message
...
On Tue, 24 Jun 2003 18:51:05 +0100, "John Smith"
wrote:

Hi,

I purchased a Zalman ZM-50HP VGA Heatsink - the smallest of the family -
today to replace the fan on my Video card - a Geforce 4460MX. I was lucky
and got it half-price.

The install was pretty straight forward but, upon installing the card

back
into its slot, the Northbridge heatsink was in the way.

I managed to overcome it by removing the two brass risers on the rear
heatsink of the ZM-50HP and it just squeezes in there now but I think

both
heatsinks are in contact with one another. Also, the ZM-50HP rear

heatsink
is incredibly close to the circuit board of the video card.

I've had it running for 5 minutes and the rear of the ZM-50HP is cool to
touch as is the Northbridge. The front of the ZM-50HP, where the fan was,

is
warm though but not even hot water bottle warm if you know what I mean.

I wonder if I could get away with simply removing the rear heatsink
altogether and just have the pipe running around the back?


Wow. I wouldn't do that. The coolant in the heatpipe has to be
condensed back into a liquid state at the rear heatsink before it can
be wicked back to the front heatsink. Regardless of the perceived
temperatures of the two sinks, I wouldn't interfere with the way the
cooler works. Also, if the sinks aren't really that warm, then maybe
you didn't get a good connection between the card's GPU and the front
sink. I don't have one of these coolers but reviewers have described
the rear heatsink as being very warm, indeed. If you're rear heatsink
is actually "cool to touch," then it suggests a problem in
installation or a manufacturing defect. You do have the pipe
installed so that the front is lower than the rear, don't you?

I don't think any other of the Zalman ZM VGA heatsinks - I saw them in

the
shop and they dwarfed the ZM-50HP - are going to stand a chance of

fitting
in the P4P800.

The Zalman tech on their board at www.zalman.com.kr has stated several
times that the ZM-80aHP does, in fact, fit on P4P800s and P4C800s, but
it fits differently from the older ZM-80HP. Is it possible that you
saw the older version?

Oh, is my PC noticeably quieter? No, not really. The VGA fan used to be
noisy in my last PC but I think it had been drowned out by the Intel fan

in
the P4P800.

Yes. It's not worth investing in one of these fanless coolers unless
the louder noise problems on your PC have already been solved.

Comments/thoughts welcome.

J.




  #2  
Old June 25th 03, 09:17 AM
John Smith
external usenet poster
 
Posts: n/a
Default

Yes, I saw the ZM-80HP and not the ZM-80aHP model which seems to fit 'above'
the VGA card so that will be fine for those of you with super big/fast
Radeon and Nividia cards.

The more I look at it the small ZM-50HP is doing a very good job indeed on
my VGA card. I am coming pretty close to ordering the 70000alcu today to get
rid of that Intel HS fan. So tempting.

J.


"
"Ron Miller" wrote in message
...
in the P4P800.
The Zalman tech on their board at www.zalman.com.kr has stated several
times that the ZM-80aHP does, in fact, fit on P4P800s and P4C800s, but
it fits differently from the older ZM-80HP. Is it possible that you
saw the older version?



  #3  
Old June 25th 03, 01:24 PM
harry wong
external usenet poster
 
Posts: n/a
Default

If the intel fan bothers you, the CNPS7000 won't be much better. A minor
drop from 42 to 41db.


"John Smith" wrote in message
...
Ron,

I had it working for, my PC that is, 6 hours non-stop last night and the
ZM-50HP eventually got warm to touch on the front. I think, to be frank,
that my Geforce 4460MX card does not generate that much heat. Zalman
themselves describe it as a low-heat card.

(I personally think anyone who has the P4P800 and who hates noise with VGA
cards would have to now only buy VGA cards with built-in heatsinks and not
fans as there is no way the bigger Zalman VGA heatsinks will fit.)

Yes, it is all fitted correctly with the heatpipe on the right way, at the
right angle, etc.

With hindsight, yes, it is quieter. I suppose I was expecting 'instant
peace' but the fan on that VGA card used to drive me nuts on my last PC.

If
I had installed it along with the Zalman CPU cooler at the same time I
probably would have been posting about how wonderfully silent my PC has
gone.

The VGA heatsink has made a difference as, prior to installing it, if I
momentarilly stopped my CPU fan I still could hear an awful lot of noise

and
could not tell whether it was the VGA fan, the case fan or the PSU fan.
After installing the VGA heatsink I, late last night, momentarilly stopped
my CPU fan and, voila, there was silence! I was amazed.

So, the next thing now is to get one of those Zalman CPU 7000-alcu

coolers.

J.


"Ron Miller" wrote in message
...
On Tue, 24 Jun 2003 18:51:05 +0100, "John Smith"
wrote:

Hi,

I purchased a Zalman ZM-50HP VGA Heatsink - the smallest of the

family -
today to replace the fan on my Video card - a Geforce 4460MX. I was

lucky
and got it half-price.

The install was pretty straight forward but, upon installing the card

back
into its slot, the Northbridge heatsink was in the way.

I managed to overcome it by removing the two brass risers on the rear
heatsink of the ZM-50HP and it just squeezes in there now but I think

both
heatsinks are in contact with one another. Also, the ZM-50HP rear

heatsink
is incredibly close to the circuit board of the video card.

I've had it running for 5 minutes and the rear of the ZM-50HP is cool

to
touch as is the Northbridge. The front of the ZM-50HP, where the fan

was,
is
warm though but not even hot water bottle warm if you know what I mean.

I wonder if I could get away with simply removing the rear heatsink
altogether and just have the pipe running around the back?


Wow. I wouldn't do that. The coolant in the heatpipe has to be
condensed back into a liquid state at the rear heatsink before it can
be wicked back to the front heatsink. Regardless of the perceived
temperatures of the two sinks, I wouldn't interfere with the way the
cooler works. Also, if the sinks aren't really that warm, then maybe
you didn't get a good connection between the card's GPU and the front
sink. I don't have one of these coolers but reviewers have described
the rear heatsink as being very warm, indeed. If you're rear heatsink
is actually "cool to touch," then it suggests a problem in
installation or a manufacturing defect. You do have the pipe
installed so that the front is lower than the rear, don't you?

I don't think any other of the Zalman ZM VGA heatsinks - I saw them in

the
shop and they dwarfed the ZM-50HP - are going to stand a chance of

fitting
in the P4P800.

The Zalman tech on their board at www.zalman.com.kr has stated several
times that the ZM-80aHP does, in fact, fit on P4P800s and P4C800s, but
it fits differently from the older ZM-80HP. Is it possible that you
saw the older version?

Oh, is my PC noticeably quieter? No, not really. The VGA fan used to be
noisy in my last PC but I think it had been drowned out by the Intel

fan
in
the P4P800.

Yes. It's not worth investing in one of these fanless coolers unless
the louder noise problems on your PC have already been solved.

Comments/thoughts welcome.

J.







  #4  
Old June 25th 03, 02:57 PM
rstlne
external usenet poster
 
Posts: n/a
Default

If the intel fan bothers you, the CNPS7000 won't be much better. A minor
drop from 42 to 41db.


you mean drop from 42db to ~25db
still maybee not a large enough drop for some, no fan in my system is over
22db AT MAX, and I would still like to take the sound down


  #5  
Old June 26th 03, 12:42 AM
Ron Miller
external usenet poster
 
Posts: n/a
Default

On Wed, 25 Jun 2003 09:17:58 +0100, "John Smith"
wrote:

Yes, I saw the ZM-80HP and not the ZM-80aHP model which seems to fit 'above'
the VGA card so that will be fine for those of you with super big/fast
Radeon and Nividia cards.

The more I look at it the small ZM-50HP is doing a very good job indeed on
my VGA card. I am coming pretty close to ordering the 70000alcu today to get
rid of that Intel HS fan. So tempting.


DO IT!

J.


"
"Ron Miller" wrote in message
...
in the P4P800.
The Zalman tech on their board at www.zalman.com.kr has stated several
times that the ZM-80aHP does, in fact, fit on P4P800s and P4C800s, but
it fits differently from the older ZM-80HP. Is it possible that you
saw the older version?



  #6  
Old June 26th 03, 12:50 AM
bigbrian
external usenet poster
 
Posts: n/a
Default

On Wed, 25 Jun 2003 23:42:43 GMT, Ron Miller
wrote:

On Wed, 25 Jun 2003 09:17:58 +0100, "John Smith"
wrote:

Yes, I saw the ZM-80HP and not the ZM-80aHP model which seems to fit 'above'
the VGA card so that will be fine for those of you with super big/fast
Radeon and Nividia cards.

The more I look at it the small ZM-50HP is doing a very good job indeed on
my VGA card. I am coming pretty close to ordering the 70000alcu today to get
rid of that Intel HS fan. So tempting.


DO IT!


Just ordered one myself with a 20db(A) Zalman 400W PSU to go with it.
We're talking quiet here.

Brian

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Is ZALMAN CNPS7000A-AlCu compatible with the ASUS P4P800 Deluxe motherboard? [email protected] Homebuilt PC's 4 April 9th 04 10:19 PM
p4p800 deluxe P4-2.4-C overclocking problems dorgold Overclocking 2 March 28th 04 03:30 PM
Asus P4P800 Deluxe - RAID controller DevilsPGD General 7 January 23rd 04 05:15 PM
Zalman passive heatsink cooler ...... Alex Overclocking 0 October 28th 03 08:58 PM
New Asus P4P800 Deluxe - No video at all? Joe Greenman General 10 October 6th 03 06:16 PM


All times are GMT +1. The time now is 10:27 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.