If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Help: Super Alien case front USB no work
My new Super-Alien case's front USB don't work. I buzzed out from the
mobo connector to the front ports, no continuity. ( mobo header works fine, tried back usb bracket on it) . Before I start taking apart the front, any help? I can just barely see the cable go up into around where the printed circuit board holding the USB header. |
#2
|
|||
|
|||
check the pin arrangements make sure your gnd+ and gnd- is setup correctly
with the board. wrote in message ... My new Super-Alien case's front USB don't work. I buzzed out from the mobo connector to the front ports, no continuity. ( mobo header works fine, tried back usb bracket on it) . Before I start taking apart the front, any help? I can just barely see the cable go up into around where the printed circuit board holding the USB header. |
#3
|
|||
|
|||
"NEW" I wouldn't take it apart. Are the connectors a one piece setup or individual single wire type?
wrote in message ... My new Super-Alien case's front USB don't work. I buzzed out from the mobo connector to the front ports, no continuity. ( mobo header works fine, tried back usb bracket on it) . Before I start taking apart the front, any help? I can just barely see the cable go up into around where the printed circuit board holding the USB header. |
#4
|
|||
|
|||
I took off the front panel and found they weren't connected at the
back of the USB connectors. Plugged them in to the header on the PC board holding the USB jacks, all set now! On Tue, 24 Feb 2004 17:16:42 GMT, "JAD" wrote: "NEW" I wouldn't take it apart. Are the connectors a one piece setup or individual single wire type? wrote in message ... My new Super-Alien case's front USB don't work. I buzzed out from the mobo connector to the front ports, no continuity. ( mobo header works fine, tried back usb bracket on it) . Before I start taking apart the front, any help? I can just barely see the cable go up into around where the printed circuit board holding the USB header. |
#5
|
|||
|
|||
that's seems to be poor quality control to me. Your spending allot more money than most for a case, you would figure that it would
be plug and play as far as the connectors go. Glad it ended up something easy. wrote in message news I took off the front panel and found they weren't connected at the back of the USB connectors. Plugged them in to the header on the PC board holding the USB jacks, all set now! On Tue, 24 Feb 2004 17:16:42 GMT, "JAD" wrote: "NEW" I wouldn't take it apart. Are the connectors a one piece setup or individual single wire type? wrote in message ... My new Super-Alien case's front USB don't work. I buzzed out from the mobo connector to the front ports, no continuity. ( mobo header works fine, tried back usb bracket on it) . Before I start taking apart the front, any help? I can just barely see the cable go up into around where the printed circuit board holding the USB header. |
#6
|
|||
|
|||
My feeling exactly. Thanks for your interest.
On Wed, 25 Feb 2004 00:25:40 GMT, "JAD" wrote: that's seems to be poor quality control to me. Your spending allot more money than most for a case, you would figure that it would be plug and play as far as the connectors go. Glad it ended up something easy. wrote in message news I took off the front panel and found they weren't connected at the back of the USB connectors. Plugged them in to the header on the PC board holding the USB jacks, all set now! On Tue, 24 Feb 2004 17:16:42 GMT, "JAD" wrote: "NEW" I wouldn't take it apart. Are the connectors a one piece setup or individual single wire type? wrote in message ... My new Super-Alien case's front USB don't work. I buzzed out from the mobo connector to the front ports, no continuity. ( mobo header works fine, tried back usb bracket on it) . Before I start taking apart the front, any help? I can just barely see the cable go up into around where the printed circuit board holding the USB header. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Looking for a PC case 1 rear 120mm and one Front bottom 120mm fan any recomendations ? | We Live For The One We Die For The One | Overclocking AMD Processors | 9 | May 21st 04 03:19 AM |
Silent Computer - Advice | David Taylor | General | 49 | October 7th 03 11:26 AM |
Thermal pad or Thermal paste? | Vin | General | 68 | September 17th 03 05:38 AM |
Cooling Questions | Peter Cavan | General | 35 | September 2nd 03 06:42 AM |
Antec Sonata case front panel firewire port | online | General | 1 | July 11th 03 01:32 AM |