If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
ATA100 hard drive not recognized when PS/2 mouse is not attached
I have a 3 or 4 year old PC, home-built. Windows 98se, AMD 1.3 ghz, 3
hard drives (10g AT66, 180g ATA100 and 250g ATA133). The large hard drives are attached to a Promise Ultra card. ECS motherboard. For quite a while (and since reinstalling all peripherals, OS, etc) I've had a mysterious problem -- when there is no mouse attached to the PS/2 port, the system (and Promise bootup sequence) does not recognize the 180g hard drive, which is configured as the primary drive on the Promise ATA100 card. The 10g hard drive is the primary boot drive I usually use. With no mouse attached, the system freezes when the Promise bootup sequence tries to find the 180g drive which is configured as the primary drive on the first ATA100 channel. After attaching a PS/2 mouse, the PC boots fine. Has anybody ever experienced this or knows what causes this? TODAY I have a much bigger problem, which is related -- something seems to have gone wrong with my PS/2 port. None of my PS/2 mice work in the PS/2 port, and so the 180g hard drive is not recognized at all. (The PS/2 port has had a rather insecure connection to the USB/PS2 adapter hooked to the mouse.) The system will boot normally -- but only sees the 10g and 250 hard drives. I have a boot drive / partitioning program active "BOOT IT" (similar to "Partition Magic"), and this program also now does not see the 180g hard drive. Attaching a USB mouse to a USB port gives me a working mouse, but still no 180g hard drive is recognized. Any helpful advice is appreciated. |
#2
|
|||
|
|||
S. Lipson wrote:
I have a 3 or 4 year old PC, home-built. Windows 98se, AMD 1.3 ghz, 3 hard drives (10g AT66, 180g ATA100 and 250g ATA133). The large hard drives are attached to a Promise Ultra card. ECS motherboard. For quite a while (and since reinstalling all peripherals, OS, etc) I've had a mysterious problem -- when there is no mouse attached to the PS/2 port, the system (and Promise bootup sequence) does not recognize the 180g hard drive, which is configured as the primary drive on the Promise ATA100 card. The 10g hard drive is the primary boot drive I usually use. With no mouse attached, the system freezes when the Promise bootup sequence tries to find the 180g drive which is configured as the primary drive on the first ATA100 channel. After attaching a PS/2 mouse, the PC boots fine. Has anybody ever experienced this or knows what causes this? TODAY I have a much bigger problem, which is related -- something seems to have gone wrong with my PS/2 port. None of my PS/2 mice work in the PS/2 port, and so the 180g hard drive is not recognized at all. (The PS/2 port has had a rather insecure connection to the USB/PS2 adapter hooked to the mouse.) The system will boot normally -- but only sees the 10g and 250 hard drives. I have a boot drive / partitioning program active "BOOT IT" (similar to "Partition Magic"), and this program also now does not see the 180g hard drive. Attaching a USB mouse to a USB port gives me a working mouse, but still no 180g hard drive is recognized. Any helpful advice is appreciated. Re-load the Promise ATA card drivers! You are experiencing IRQ resource conflicts. And, without the ATA card, your system cannot see the large hard drive! |
#3
|
|||
|
|||
patrick wrote in message .. .
S. Lipson wrote: I have a 3 or 4 year old PC, home-built. Windows 98se, AMD 1.3 ghz, 3 hard drives (10g AT66, 180g ATA100 and 250g ATA133). The large hard drives are attached to a Promise Ultra card. ECS motherboard. For quite a while (and since reinstalling all peripherals, OS, etc) I've had a mysterious problem -- when there is no mouse attached to the PS/2 port, the system (and Promise bootup sequence) does not recognize the 180g hard drive, which is configured as the primary drive on the Promise ATA100 card. The 10g hard drive is the primary boot drive I usually use. With no mouse attached, the system freezes when the Promise bootup sequence tries to find the 180g drive which is configured as the primary drive on the first ATA100 channel. After attaching a PS/2 mouse, the PC boots fine. Has anybody ever experienced this or knows what causes this? TODAY I have a much bigger problem, which is related -- something seems to have gone wrong with my PS/2 port. None of my PS/2 mice work in the PS/2 port, and so the 180g hard drive is not recognized at all. (The PS/2 port has had a rather insecure connection to the USB/PS2 adapter hooked to the mouse.) The system will boot normally -- but only sees the 10g and 250 hard drives. I have a boot drive / partitioning program active "BOOT IT" (similar to "Partition Magic"), and this program also now does not see the 180g hard drive. Attaching a USB mouse to a USB port gives me a working mouse, but still no 180g hard drive is recognized. Any helpful advice is appreciated. Re-load the Promise ATA card drivers! You are experiencing IRQ resource conflicts. And, without the ATA card, your system cannot see the large hard drive! Thanks for responding. I have two large hard drives attached to the Promise Ultra100 card -- 180gb and 250gb. The Promise card has two channels (2 cable connections), and I've connected each hard drive on its own channel (each is a Master). The Promise UltraATA100 driver recognizes the 250gb drive but not the 180gb drive. I have tried switching hard drives and cables in every combination -- using both drives and each one separately. In every test, the 180gb drive is not recognized by the BIOS (or anything else). The 250gb is recognized and functions properly in every test. The Promise ATA driver uses IRQ 5. Because of this I might guess that the ATA driver is not the problem. But should I try reinstalling it anyway? If the BIOS doesn't recognize the hard drive, is this a physical problem with the hard drive? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help With Hard Drive Replacement | Boba & Ilinka | General | 4 | December 16th 04 02:42 PM |
When the PS/2 port is not used, an ATA100 (primary) drive is not recognized | S. Lipson | General | 0 | July 25th 04 12:30 PM |
Mysterious Hard Drive Problem | Bill Anderson | General | 4 | January 18th 04 03:43 AM |
Replacing master hard drive | Lew | General | 2 | January 17th 04 06:39 PM |
How Move OS XP from Old to New HD? | Nehmo Sergheyev | Homebuilt PC's | 80 | January 12th 04 05:10 PM |