If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
PC/electronics help needed
Greetings all.
Assume for a moment that I have no knowledge of electronics (not true, but I only know what I've picked up and that's rather patchy). I'm looking to make a little addon for my PC and I need a little help. I'm after making 3 time/date displays using 7-segment (numbers) and 10-segment (letters) LED displays. One of them should actually show the correct time, the others I'd like to show other static times, preferably with the option to change them occasionally. The latter parts should be within my reach but the actual clock is a bit more of a problem, our school was a bit crap and didn't actually teach us how to do that. I'd rather make it from scratch but I'll butcher an alarm clock if I have to. The other thing is that it needs to be powered from the PC's power supply, so it'll need to run on either 5V or 12V, with some form of battery backup to power just the real clock when the machine is switched off. If somehow it could be made to display the system's internal time that would be wonderful, but not necessary. Any help at all would be vastly appreciated. DjBx |
#2
|
|||
|
|||
Daniel J Beardsall wrote:
...I'm looking to make a little addon for my PC and I need a little help. I'm after making 3 time/date displays using 7-segment (numbers) and 10-segment (letters) LED displays. One of them should actually show the correct time, the others I'd like to show other static times, preferably with the option to change them occasionally. The latter parts should be within my reach but the actual clock is a bit more of a problem, our school was a bit crap and didn't actually teach us how to do that. I would ask in the electronics groups. sci.electronics... Good luck. The other thing is that it needs to be powered from the PC's power supply, so it'll need to run on either 5V or 12V, with some form of battery backup to power just the real clock when the machine is switched off. If somehow it could be made to display the system's internal time that would be wonderful, but not necessary. Any help at all would be vastly appreciated. DjBx |
#3
|
|||
|
|||
Not sure what you want but:
first, 5 or 12 from the PC is not problem, even get 5 vdc from the USB port, second: you want the system time thats displayed in the task bar on the bottom right of your monitor displayed on your gadget? Then would it be connected to the computer thru the parallel port or serial or USB? When computer shuts down, does this display keep going, like automatically switching to an internal clock, then back to computer when its turned on again? You could write a program to send any number you want out the parallel port, read he system time, send out the hoy=urs, then send out the minutes. On Thu, 02 Dec 2004 02:05:31 +0000, Daniel J Beardsall wrote: Greetings all. Assume for a moment that I have no knowledge of electronics (not true, but I only know what I've picked up and that's rather patchy). I'm looking to make a little addon for my PC and I need a little help. I'm after making 3 time/date displays using 7-segment (numbers) and 10-segment (letters) LED displays. One of them should actually show the correct time, the others I'd like to show other static times, preferably with the option to change them occasionally. The latter parts should be within my reach but the actual clock is a bit more of a problem, our school was a bit crap and didn't actually teach us how to do that. I'd rather make it from scratch but I'll butcher an alarm clock if I have to. The other thing is that it needs to be powered from the PC's power supply, so it'll need to run on either 5V or 12V, with some form of battery backup to power just the real clock when the machine is switched off. If somehow it could be made to display the system's internal time that would be wonderful, but not necessary. Any help at all would be vastly appreciated. DjBx |
#4
|
|||
|
|||
Not sure what you want but:
first, 5 or 12 from the PC is not problem, even get 5 vdc from the USB port, Yes I know, I intend to run it off one of the internal Molex connectors. second: you want the system time thats displayed in the task bar on the bottom right of your monitor displayed on your gadget? Then would it be connected to the computer thru the parallel port or serial or USB? Yes. Any of those, whichever turns out to be easiest. Which from what I've gathered would be parallel. When computer shuts down, does this display keep going, like automatically switching to an internal clock, then back to computer when its turned on again? You could write a program to send any number you want out the parallel port, read he system time, send out the hoy=urs, then send out the minutes. Yes, I'd like the clock to be sort of independent with occasional updates from the PC clock (mostly to save the hassle of setting it manually). The program isn't the problem, I could knock something up in VB, it's getting something that can translate my outputs and display it that's the problem. DjBx |
#5
|
|||
|
|||
It's real easy in VB.net, but remember, XP will not allow you to
program the ports, you need a "kernal driver" that runs in a special mode. This link explains it: http://www.logix4u.net/inpout32.htm My I/O programs start by calling ShellExec to run a script that puts you into the proper user mode. On Fri, 03 Dec 2004 06:12:45 +0000, Daniel J Beardsall wrote: Not sure what you want but: first, 5 or 12 from the PC is not problem, even get 5 vdc from the USB port, Yes I know, I intend to run it off one of the internal Molex connectors. second: you want the system time thats displayed in the task bar on the bottom right of your monitor displayed on your gadget? Then would it be connected to the computer thru the parallel port or serial or USB? Yes. Any of those, whichever turns out to be easiest. Which from what I've gathered would be parallel. When computer shuts down, does this display keep going, like automatically switching to an internal clock, then back to computer when its turned on again? You could write a program to send any number you want out the parallel port, read he system time, send out the hoy=urs, then send out the minutes. Yes, I'd like the clock to be sort of independent with occasional updates from the PC clock (mostly to save the hassle of setting it manually). The program isn't the problem, I could knock something up in VB, it's getting something that can translate my outputs and display it that's the problem. DjBx |
#6
|
|||
|
|||
The problem with an alarm clock is that the chip is
completely contained. The only information coming out would be seven segment displays - multiplexed. You would have to convert that back to some usable form OR build a memory device to store those multiplexed seven segment outputs and then drive the other displays. Four digits times seven segments plus AM/PM is 29 D flipflop latches and LED display drivers. What type of time do you want to store? For example, if time of day, then the alarm clock solution is better. AC powered clocks synchronize with the 60 Hz power line - whose accuracy is traceable to the National Bureau of Standards. To avoid the complexity of same, the alarm clock would be a good foundation to start construction. You would probably have to beef up or supplement the alarm clock's power supply to power your latching registers and two additional displays. Another alternative is to start from scrap with a single chip computer. Again, your timing crystal accuracy is just another consideration. But a single chip computer affords you great flexibility to enhance your design. Daniel J Beardsall wrote: Greetings all. Assume for a moment that I have no knowledge of electronics (not true, but I only know what I've picked up and that's rather patchy). I'm looking to make a little addon for my PC and I need a little help. I'm after making 3 time/date displays using 7-segment (numbers) and 10-segment (letters) LED displays. One of them should actually show the correct time, the others I'd like to show other static times, preferably with the option to change them occasionally. The latter parts should be within my reach but the actual clock is a bit more of a problem, our school was a bit crap and didn't actually teach us how to do that. I'd rather make it from scratch but I'll butcher an alarm clock if I have to. The other thing is that it needs to be powered from the PC's power supply, so it'll need to run on either 5V or 12V, with some form of battery backup to power just the real clock when the machine is switched off. If somehow it could be made to display the system's internal time that would be wonderful, but not necessary. Any help at all would be vastly appreciated. |
#7
|
|||
|
|||
The problem with an alarm clock is that the chip is
completely contained. The only information coming out would be seven segment displays - multiplexed. You would have to convert that back to some usable form OR build a memory device to store those multiplexed seven segment outputs and then drive the other displays. Four digits times seven segments plus AM/PM is 29 D flipflop latches and LED display drivers. The other displays would be independent of the actual clock, if that's what you mean. And yes, when I mentioned butchering an alarm clock that was mostly as a last-resort kind of option. What type of time do you want to store? For example, if time of day, then the alarm clock solution is better. AC powered clocks synchronize with the 60 Hz power line - whose accuracy is traceable to the National Bureau of Standards. To avoid the complexity of same, the alarm clock would be a good foundation to start construction. You would probably have to beef up or supplement the alarm clock's power supply to power your latching registers and two additional displays. The problem there is that I'm not in the US, I'm in the UK, and our electrical supply isn't quite so simple. It's mostly 50Hz but can fluctuate wildly, which often interferes with clocks. Besides, I'm not looking to run it off direct mains, I'm looking to run it off computer power, so a battery-powered alarm clock was more what I had in mind. Another alternative is to start from scrap with a single chip computer. Again, your timing crystal accuracy is just another consideration. But a single chip computer affords you great flexibility to enhance your design. Now you're talking. But I wouldn't know where to start hooking something like that into something capable of driving LED segment displays. Which I suppose is ultimately the help I'm after. Thankyou for your response. DjBx |
#8
|
|||
|
|||
Daniel J Beardsall wrote:
The problem with an alarm clock is that the chip is completely contained. The only information coming out would be seven segment displays - multiplexed. You would have to convert that back to some usable form OR build a memory device to store those multiplexed seven segment outputs and then drive the other displays. Four digits times seven segments plus AM/PM is 29 D flipflop latches and LED display drivers. The other displays would be independent of the actual clock, if that's what you mean. And yes, when I mentioned butchering an alarm clock that was mostly as a last-resort kind of option. What type of time do you want to store? For example, if time of day, then the alarm clock solution is better. AC powered clocks synchronize with the 60 Hz power line - whose accuracy is traceable to the National Bureau of Standards. To avoid the complexity of same, the alarm clock would be a good foundation to start construction. You would probably have to beef up or supplement the alarm clock's power supply to power your latching registers and two additional displays. The problem there is that I'm not in the US, I'm in the UK, and our electrical supply isn't quite so simple. It's mostly 50Hz but can fluctuate wildly, which often interferes with clocks. Besides, I'm not looking to run it off direct mains, I'm looking to run it off computer power, so a battery-powered alarm clock was more what I had in mind. Another alternative is to start from scrap with a single chip computer. Again, your timing crystal accuracy is just another consideration. But a single chip computer affords you great flexibility to enhance your design. Now you're talking. But I wouldn't know where to start hooking something like that into something capable of driving LED segment displays. Which I suppose is ultimately the help I'm after. Thankyou for your response. DjBx I'm still not sure what you're trying to do, precisely, but maybe this will stimulate some ideas. http://www.rentron.com/Products/SLED4C.htm |
#9
|
|||
|
|||
AC electric cannot vary wildly because all grid generators
must match up perfectly with all others - or the entire grid collapses. To find a clock that varies wildly, visit a PC clock. That clock is way too inaccurate to control the 50 Hz grid - where timing accuracy is essential. Use a PC as the timing source. Therefore you only need write special software to write to displays- ie driven through parallel ports. But then why bother with fancy hardware displays? You can put up clock displays in Windows on the monitor. Previously posted was using an alarm clock 'kludge' - every other display is independent of the actual clock - except when the display number is first latched from a master display. Appreciate everything posted up to now is perfectly matching your request - because details are missing. What are the details? For example, the grid 50 Hz remains a most accurate source of timing which is why AC electric clocks remain on time every day - without resetting every week. If 50 Hz AC is not accurate enough, then anything in a PC or in the embedded processor is even worse. IOW you did not provide a necessary detail such as the number for timing accuracy. You did not say where those other displays get their numbers. Are you trying to display a time of day, or time of event. For that matter, what is wrong with a controller from a defective microwave oven? How to connect to a display? First select the display. Then find the driver chip for that type of display. IOW download datasheets. Read some 3 or eight pages chock full of information (assume something like 15+ minutes per page). If that example (rentron.com) is what you want, then why not buy it? I remain completely confused by what you are trying to do. If 50 Hz AC power is not accurate enough, then this example is even worse. Just more little contradictory details that completely confused me. It is possible that you have not yet learned an engineer's mentality. This project is how you learn so much. Same reason why to teach why the military want people educated in the temperament of reality. Notice what you may have perceived as a simple project might take weeks. Something that would become obvious once you first list those details. The military teaches their future officers to be engineers. To learn that reality is not as simplistic as taught in secondary school. To learn temperament that comes from putting initial ideas into reality. Making ideas into reality is rarely taught in general education. We learn it by doing what you are trying to accomplish here. Currently, you have starve your request for information with insufficient details. Daniel J Beardsall wrote: The problem with an alarm clock is that the chip is completely contained. The only information coming out would be seven segment displays - multiplexed. You would have to convert that back to some usable form OR build a memory device to store those multiplexed seven segment outputs and then drive the other displays. Four digits times seven segments plus AM/PM is 29 D flipflop latches and LED display drivers. The other displays would be independent of the actual clock, if that's what you mean. And yes, when I mentioned butchering an alarm clock that was mostly as a last-resort kind of option. What type of time do you want to store? For example, if time of day, then the alarm clock solution is better. AC powered clocks synchronize with the 60 Hz power line - whose accuracy is traceable to the National Bureau of Standards. To avoid the complexity of same, the alarm clock would be a good foundation to start construction. You would probably have to beef up or supplement the alarm clock's power supply to power your latching registers and two additional displays. The problem there is that I'm not in the US, I'm in the UK, and our electrical supply isn't quite so simple. It's mostly 50Hz but can fluctuate wildly, which often interferes with clocks. Besides, I'm not looking to run it off direct mains, I'm looking to run it off computer power, so a battery-powered alarm clock was more what I had in mind. Another alternative is to start from scrap with a single chip computer. Again, your timing crystal accuracy is just another consideration. But a single chip computer affords you great flexibility to enhance your design. Now you're talking. But I wouldn't know where to start hooking something like that into something capable of driving LED segment displays. Which I suppose is ultimately the help I'm after. |
#10
|
|||
|
|||
w_tom wrote:
AC electric cannot vary wildly because all grid generators must match up perfectly with all others - or the entire grid collapses. To find a clock that varies wildly, visit a PC clock. That clock is way too inaccurate to control the 50 Hz grid - where timing accuracy is essential. Power grid frequency varies automatically with the difference between supply and demand and is controlled by opening and closing the steam valves of the turbines that drive the generators. In the continental European grid (UCTE), the spec says that the time-scale defined by the rotating grid phase vector must remain within +/- 30 seconds of UTC. The UCTE control center in Laufenbourg, Switzerland sends out instructions every 24 hours to shift the nominal frequency of 50.0 Hz, if necessary, to either 49.99 or 50.01 Hz (+/- 10 mHz) if the network clock starts to drift away from UTC too far. For comparison: the measured frequency deviation from the nominal frequency is not supposed to be more than 40 mHz for more than 10% of the time and not more than 60 mHz for more than 1% of time. As such, at any moment in time the AC grid can 'vary wildly' (subjective) compared to the tolerances of a PC clock (typical RTC 32.768 kHz crystal being 20ppm @ 25C, which can accumulate to being off 52s after a month). The difference is that the power grid is routinely (24 hours) 'corrected' to bring it back so, over the long term, it remains within tolerance whereas a PC clock's error just keeps accumulating, unless one does a similar thing and syncs it with a more accurate time reference. Use a PC as the timing source. Therefore you only need write special software to write to displays- ie driven through parallel ports. But then why bother with fancy hardware displays? You can put up clock displays in Windows on the monitor. Previously posted was using an alarm clock 'kludge' - every other display is independent of the actual clock - except when the display number is first latched from a master display. Appreciate everything posted up to now is perfectly matching your request - because details are missing. What are the details? For example, the grid 50 Hz remains a most accurate source of timing which is why AC electric clocks remain on time every day - without resetting every week. If 50 Hz AC is not accurate enough, then anything in a PC or in the embedded processor is even worse. IOW you did not provide a necessary detail such as the number for timing accuracy. You did not say where those other displays get their numbers. Are you trying to display a time of day, or time of event. For that matter, what is wrong with a controller from a defective microwave oven? How to connect to a display? First select the display. Then find the driver chip for that type of display. IOW download datasheets. Read some 3 or eight pages chock full of information (assume something like 15+ minutes per page). If that example (rentron.com) is what you want, then why not buy it? I remain completely confused by what you are trying to do. If 50 Hz AC power is not accurate enough, then this example is even worse. Just more little contradictory details that completely confused me. It is possible that you have not yet learned an engineer's mentality. This project is how you learn so much. Same reason why to teach why the military want people educated in the temperament of reality. Notice what you may have perceived as a simple project might take weeks. Something that would become obvious once you first list those details. The military teaches their future officers to be engineers. To learn that reality is not as simplistic as taught in secondary school. To learn temperament that comes from putting initial ideas into reality. Making ideas into reality is rarely taught in general education. We learn it by doing what you are trying to accomplish here. Currently, you have starve your request for information with insufficient details. Daniel J Beardsall wrote: The problem with an alarm clock is that the chip is completely contained. The only information coming out would be seven segment displays - multiplexed. You would have to convert that back to some usable form OR build a memory device to store those multiplexed seven segment outputs and then drive the other displays. Four digits times seven segments plus AM/PM is 29 D flipflop latches and LED display drivers. The other displays would be independent of the actual clock, if that's what you mean. And yes, when I mentioned butchering an alarm clock that was mostly as a last-resort kind of option. What type of time do you want to store? For example, if time of day, then the alarm clock solution is better. AC powered clocks synchronize with the 60 Hz power line - whose accuracy is traceable to the National Bureau of Standards. To avoid the complexity of same, the alarm clock would be a good foundation to start construction. You would probably have to beef up or supplement the alarm clock's power supply to power your latching registers and two additional displays. The problem there is that I'm not in the US, I'm in the UK, and our electrical supply isn't quite so simple. It's mostly 50Hz but can fluctuate wildly, which often interferes with clocks. Besides, I'm not looking to run it off direct mains, I'm looking to run it off computer power, so a battery-powered alarm clock was more what I had in mind. Another alternative is to start from scrap with a single chip computer. Again, your timing crystal accuracy is just another consideration. But a single chip computer affords you great flexibility to enhance your design. Now you're talking. But I wouldn't know where to start hooking something like that into something capable of driving LED segment displays. Which I suppose is ultimately the help I'm after. |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Are mains surge protectors needed in the UK? | John McGaw | Homebuilt PC's | 177 | July 20th 04 08:19 PM |
250 watt and ATX 2.1 needed to kep xp 2000 board running ? | We Live for the One we Die for the One | Overclocking | 0 | May 31st 04 02:38 PM |
250 watt and ATX 2.1 needed to kep xp 2000 board running ? | jaster | Homebuilt PC's | 0 | May 31st 04 07:43 AM |
new proc fan needed, looking for recommendations | boneheadlio | Homebuilt PC's | 2 | February 28th 04 12:13 AM |
kluge needed: CF-II (or SDIO) <---> MemoryStick (or SmartMedia/MMS) | Alan Horowitz | Homebuilt PC's | 4 | January 15th 04 08:24 PM |