If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
What is limiting?
I have overclocked my system to FSB=244 at Mem:CPU set to 4:5. This
overclocks the CPU, but, underclocks the ram. The system has been stable for the last few months. I have just got two 512MB sticks of PC3200 DDR. Replaced the two old sticks of 256MB PC3200 with these. Now, the system is unstable at FSB=244. It is only stable at FSB=238. This suggested to me that the new DDR was limiting since that was the only component that had been changed. So, I ran memtest, with the new DDR, at FSB=215 with Mem:CPU = 1:1 and it ran fine for 7.5 hours with no errors. Now, if the DDR is fine at 215, why should it limit at 244x4/5=195? What is limiting? Thanks, Navid ASUS P4P800 deluxe P4C 2.6GHz Befo 2xKingston 256MB DDR400 3-3-3 Now: 2xKingston 512MB DDR400 3-3-3 |
#2
|
|||
|
|||
Hi,
There is no reason for the memorys not working, especially under specs... Check what are the timmings youre pushing them or if one of them is not working... ------------------------------------------------------- Stormgiant Asus P4P800-Deluxe NW3000@3915 FSB261 on WC 512MB OCZ BH-5 @DDR522 2-2-2-5 Power Color ATi 9800XT 520/410 ------------------------------------------------------- On Thu, 01 Jul 2004 12:31:45 GMT, "Navid" wrote: I have overclocked my system to FSB=244 at Mem:CPU set to 4:5. This overclocks the CPU, but, underclocks the ram. The system has been stable for the last few months. I have just got two 512MB sticks of PC3200 DDR. Replaced the two old sticks of 256MB PC3200 with these. Now, the system is unstable at FSB=244. It is only stable at FSB=238. This suggested to me that the new DDR was limiting since that was the only component that had been changed. So, I ran memtest, with the new DDR, at FSB=215 with Mem:CPU = 1:1 and it ran fine for 7.5 hours with no errors. Now, if the DDR is fine at 215, why should it limit at 244x4/5=195? What is limiting? Thanks, Navid ASUS P4P800 deluxe P4C 2.6GHz Befo 2xKingston 256MB DDR400 3-3-3 Now: 2xKingston 512MB DDR400 3-3-3 |
#3
|
|||
|
|||
"Stormgiant" wrote in message ... Hi, There is no reason for the memorys not working, especially under specs... Check what are the timmings youre pushing them or if one of them is not working... ------------------------------------------------------- Stormgiant Asus P4P800-Deluxe NW3000@3915 FSB261 on WC 512MB OCZ BH-5 @DDR522 2-2-2-5 Power Color ATi 9800XT 520/410 ------------------------------------------------------- Hi, It actually turned out that I had disturbed the air flow in the case when I installed the new memory. After I bundled all the wires and cleaned up everything and put fresh Arctic Silver on the CPU, it went to even higher frequencies. It is now stable at FSB=246 with the new memory (dual channel). So, it was the CPU that was limiting. Navid |
#4
|
|||
|
|||
Nice to see it worked out fine.
Now, try to get better timmings out of those memories ------------------------------------------------------- Stormgiant Asus P4P800-Deluxe NW3000@3915 FSB261 on WC 512MB OCZ BH-5 @DDR522 2-2-2-5 Power Color ATi 9800XT 520/410 ------------------------------------------------------- On Sat, 10 Jul 2004 16:40:22 GMT, "Navid" wrote: "Stormgiant" wrote in message .. . Hi, There is no reason for the memorys not working, especially under specs... Check what are the timmings youre pushing them or if one of them is not working... ------------------------------------------------------- Stormgiant Asus P4P800-Deluxe NW3000@3915 FSB261 on WC 512MB OCZ BH-5 @DDR522 2-2-2-5 Power Color ATi 9800XT 520/410 ------------------------------------------------------- Hi, It actually turned out that I had disturbed the air flow in the case when I installed the new memory. After I bundled all the wires and cleaned up everything and put fresh Arctic Silver on the CPU, it went to even higher frequencies. It is now stable at FSB=246 with the new memory (dual channel). So, it was the CPU that was limiting. Navid |
Thread Tools | |
Display Modes | |
|
|