If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Using ribbon cable for panel-mount USB-2 motherboard cable?
Is there some reason that a panel-mounted USB cable like this:
http://m4.sourcingmap.com/photo_new/...x0042_ux_c.jpg couldn't be made with ribbon cable? Assuming that there are female USB connectors designed for press-fit ribbon cable? You could make up a panel-mounted connector solution in 2 minutes using ribbon cable. ? |
#2
|
|||
|
|||
Using ribbon cable for panel-mount USB-2 motherboard cable?
"PC Guy" "PC"@Guy .com wrote in message ... Is there some reason that a panel-mounted USB cable like this: http://m4.sourcingmap.com/photo_new/...x0042_ux_c.jpg couldn't be made with ribbon cable? Assuming that there are female USB connectors designed for press-fit ribbon cable? You could make up a panel-mounted connector solution in 2 minutes using ribbon cable. ? I think you'd still have to find a way to shield the whole cable to avoid electrical interference. -- SC Tom |
#3
|
|||
|
|||
Using ribbon cable for panel-mount USB-2 motherboard cable?
PC Guy wrote:
Is there some reason that a panel-mounted USB cable like this: http://m4.sourcingmap.com/photo_new/...x0042_ux_c.jpg couldn't be made with ribbon cable? Assuming that there are female USB connectors designed for press-fit ribbon cable? You could make up a panel-mounted connector solution in 2 minutes using ribbon cable. ? There is a 650 page spec for USB2. "High-/full-speed cable consists of one 28 to 20 AWG non-twisted power pair and one 28 AWG twisted data pair with an aluminum metallized polyester inner shield, 28 AWG stranded tinned copper drain wire, 65% tinned copper wire interwoven (braided) outer shield, and PVC outer jacket." That means the power wires are a different gauge than the signal wires. Good USB cables use thicker power wires, to meet the VBUS drop budget at 500mA current flow. If you used ribbon cable, you'd need to use something like teflon ribbon, to meet a roughly 90 ohm differential impedance on D+/D-. They do make custom ribbon cables, including SCSI ribbons with things like twisted pairs right in the ribbon. Any cost savings would go out the window, when you price a roll of cable like that. With teflon, you might be able to avoid the need for twisted pair, and just run a pair flat. Setting the number of twists per inch, helps tune the impedance value, and twisting also helps if you have true differential receivers on the end (which the USB ones won't be - electronics are notorious for not using amps with good common mode rejection). That's what I'm looking at when I talk about "lead dress". The D+/D- pair are supposed to remain 90 ohms, and won't be when untwisted and sitting in free space. The "uncontrolled" part of the cable (with shield removed, and the shield changes the impedance) should be as short as possible, to reduce reflections. A guess would be, yes, you could make a cable which is flat in nature. They even make ribbon cable with external shielding. So the USB cable could be "flattened", if there was a requirement for it (round cable wouldn't fit through a hole, say). But as a "quick and dirty", it might not be close enough, and might cause a detectable error rate. The cabling spec has diff TDR tests to meet, which you could subject the test ribbon cable to, to determine whether it is close enough or not. On USB3, the shield is apparently not enough, and an Intel document shows USB3 cables throw off enough microwaves, to kill adjacent Wifi signals. Peripherals require careful shielding, to stop that from happening. Shielding that you know peripheral makers aren't using, or testing for. The only consequence, is a "surprise" when the laptop Wifi doesn't work, and you have to "move the cable this way and that way", until Wifi or an adjacent wireless keyboard/mouse start working. I don't know if Intel wrote this document as FUD, to push Thunderbolt, or it's an honest effort to warn the industry about more care being needed with 5Gbit/sec USB3 signals and their associated broadband spectrum. USB3 has even more extreme requirements, a higher allowed VBUS current. The three diff pairs would probably be good candidates for the teflon ribbon (with a ground wire between each pair), but again, you'd need to check for crosstalk and reflections with TDR and other tests. The ribbon would likely "radiate like a *******". You can get doubly shielded ribbon, with rubber on the outside, and that is thick enough, you might as well go back to the round cable again :-) As for insulation displacement connections, for the higher speed cases you'd want to investigate how that affects lead dress, and how much unshielded cable area is present as a result. If the ribbon is shielded, you have to figure out how to connect (terminate) the shield/drain at the end. Overmolded cables hide all those details, so we can't see how it is done. And most of this stuff is outside my pay scale. "If I made your cables from scratch, they'd probably suck." But I have worked with people who do this stuff. They have the TDR, network analyser, test head, to do the characterization. Paul |
#4
|
|||
|
|||
Using ribbon cable for panel-mount USB-2 motherboard cable?
On Thursday, July 17, 2014 9:36:37 PM UTC-7, PC Guy wrote:
Is there some reason that a panel-mounted USB cable like this: http://m4.sourcingmap.com/photo_new/...x0042_ux_c.jpg couldn't be made with ribbon cable? Assuming that there are female USB connectors designed for press-fit ribbon cable? Maybe if the cables are kept as short as those in the photo, but I have doubts because: 1. USB 2.0 front panel kits with cables as short as 12" (usually they're at least 18" - 24") have twisted pair cables. 2. External USB 2.0 disk drives containing internal parallel IDE drives rated for ATA/133 (signals switch at up to 133M/second) have a very short ribbon cable between the drive and IDE-USB bridge card, often 2", and it's not ordinary ribbon cable but the 80-wire type, where every other wire is a ground to shield the adjacent signal wires. 3. I once made a 10' Ethernet cable out of flat ribbon cable, and the network cards wouldn't run faster than 10Mb/sec. But when the cable was made from 500' of Cat 5e cable, the cards ran at 100Mb/sec. The official maximum length is supposed to be only 328'. OTOH you don't need to use shielded cable because it's the twisted pairs that matter most, and it's not hard to split up a ribbon cable into individual wires and twist them into pairs. It's also not that hard to attach individual wires to one of those press- together connectors (leave them a bit long, and trim the excess after you press it, making sure no individual strands dangle. Maybe it would be best to get a cheap USB extension cable and cut off one end to attach it to the press-fit conector. I'd leave that cable as long as possible, in case of mistakes. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Looking for: Panel-mount USB A socket, + 35cm bare-end cable | Jim Howes | UK Computer Vendors | 5 | November 20th 06 01:28 PM |
LCD Ribbon Cable? | islander | Compaq Computers | 0 | March 4th 05 01:41 AM |
LCD Ribbon Cable? | JLA | Compaq Computers | 0 | March 4th 05 01:41 AM |
LCD Ribbon Cable? | islander | Compaq Computers | 0 | March 4th 05 01:41 AM |
Ribbon Cable | BP | Storage (alternative) | 8 | July 15th 03 10:43 PM |