A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » General Hardware & Peripherals » Storage (alternative)
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

40pin FC-AL Fibre / Fiber Channel Hard Drive



 
 
Thread Tools Display Modes
  #1  
Old May 27th 09, 04:18 AM posted to comp.sys.ibm.pc.hardware.storage
DevilsPGD[_3_]
external usenet poster
 
Posts: 181
Default 40pin FC-AL Fibre / Fiber Channel Hard Drive

I've recently come into possession of some Fibre Channel 40 pin drives
(ST3146807FC). These are FC-AL, unfortunately I misinterpreted the
specs on a controller I was looking at before I snagged the drives.

Any suggestions as to what sort of host controllers I might look at
and/or suggestions for shelves/enclosures/adapters?

I've got 8 drives, ideally I'd run 4 per server across two servers,
although if the cost difference is substantial I could put them on a
single box.
  #4  
Old May 28th 09, 09:31 PM posted to comp.sys.ibm.pc.hardware.storage
DevilsPGD[_3_]
external usenet poster
 
Posts: 181
Default 40pin FC-AL Fibre / Fiber Channel Hard Drive

In message shawn
was claimed to have wrote:

On Wed, 27 May 2009 06:16:05 +0000 (UTC),
wrote:

DevilsPGD kenjka:
Any suggestions as to what sort of host controllers I might look at
and/or suggestions for shelves/enclosures/adapters?


Look for QLogic and Emulex FC RAID controllers... Maybe there is
something...

Also, watch out for the drive low-level formatting... If they're formatted
as 520 bytes per sector, than those are EMC CLARiiON drives and you'll have
to reformat them via some utility like SCSITool...


I wouldn't be surprised if they are EMC Clariion drives since the
likely source of the drives was known for using EMC equipment in the
past for years. That old equipment is being decomissioned now.


Good guess

However, I'm expecting that I can deal with the reformatting later...
Unfortunately my plan for a controller isn't working out, so I'm back to
the drawing board.
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Defective Seagate SCSI, IDE, SATA and Fibre Channel hard drives corbeil_the _specialist Storage (alternative) 1 February 23rd 07 09:38 AM
Fiber Channel Sniffer ophir Storage & Hardrives 0 September 17th 06 09:12 AM
Fiber channel tape drive config help Kyle Tucker Storage & Hardrives 8 December 28th 04 04:08 AM
How to talk to Fiber Channel drives in an array on Win NT Matthias Storage & Hardrives 4 October 19th 04 06:57 PM
IBM LTO Fibre Channel Tape Drive Rewinding In A Loop CHANGE USERNAME TO westes Storage (alternative) 0 July 13th 03 09:02 PM


All times are GMT +1. The time now is 01:11 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.