Drive is 'not stamped for monitoring'

Just rebuilding a Proliant 5500 and ran array diagnostic and it asked
me if I would like to see the faults.

"Port 1 Drive 3 is not stamped for monitoring"

I've now swapped out the drive for a spare and the rebuilt array
reports 'no problems detected'. What's with the other drive and can it
be 'stamped'?

Regards,
Jason.
---
Replace nntp with my name to reply.
N0 5pAm H3r3: Include this tagline to pass my spam filter.

NFC ... i have never seen that before. Maybe that is compaq's way of saying
that your drive didnt come from them ???

-= LC =-

"Jason Arthurs" wrote in message
news
Just rebuilding a Proliant 5500 and ran array diagnostic and it asked
me if I would like to see the faults.

"Port 1 Drive 3 is not stamped for monitoring"

I've now swapped out the drive for a spare and the rebuilt array
reports 'no problems detected'. What's with the other drive and can it
be 'stamped'?

Regards,
Jason.
---
Replace nntp with my name to reply.
N0 5pAm H3r3: Include this tagline to pass my spam filter.

however ... my googlefinger did lead me to this:

http://forums1.itrc.hp.com/service/f...85206+28353475

-= LC=-

"NuTCrAcKeR" wrote in message
t...
NFC ... i have never seen that before. Maybe that is compaq's way of
saying that your drive didnt come from them ???

-= LC =-

"Jason Arthurs" wrote in message
news
Just rebuilding a Proliant 5500 and ran array diagnostic and it asked
me if I would like to see the faults.

"Port 1 Drive 3 is not stamped for monitoring"

I've now swapped out the drive for a spare and the rebuilt array
reports 'no problems detected'. What's with the other drive and can it
be 'stamped'?

Regards,
Jason.
---
Replace nntp with my name to reply.
N0 5pAm H3r3: Include this tagline to pass my spam filter.

My drive is definately an original Compaq drive I can see the Compaq
logo and part number through the top of the caddy.

Ironically the drive in question had just been attached to a SA431
which came out of a ML350 (as per the drive on the HP site posting).
But at the time of the error it was attached to a Smart-2DH, I shall
put this one in reserve and mark it as questionable.

I've got a Proliant 2500 to rebuild later and I'll see if the array in
that one likes it any better...

Thanks,
Jason.


On Mon, 14 Nov 2005 06:51:35 -0600, "NuTCrAcKeR"
wrote:

however ... my googlefinger did lead me to this:

http://forums1.itrc.hp.com/service/f...85206+28353475

-= LC=-

"NuTCrAcKeR" wrote in message
et...
NFC ... i have never seen that before. Maybe that is compaq's way of
saying that your drive didnt come from them ???

-= LC =-

"Jason Arthurs" wrote in message
news
Just rebuilding a Proliant 5500 and ran array diagnostic and it asked
me if I would like to see the faults.

"Port 1 Drive 3 is not stamped for monitoring"

I've now swapped out the drive for a spare and the rebuilt array
reports 'no problems detected'. What's with the other drive and can it
be 'stamped'?

Regards,
Jason.
---
Replace nntp with my name to reply.
N0 5pAm H3r3: Include this tagline to pass my spam filter.




---
Replace nntp with my name to reply.
N0 5pAm H3r3: Include this tagline to pass my spam filter.