Why mechanical failure causes HDD being undetectable by bios or OS ?

Hi!
Could someone please explain why in the case of *mechanical* failure HD
becomes sometimes undetected by BIOS and/or the operating system (e.g. win xp
or linux)?
If it was an electronic failure then such behaviour would be obious, but why
the same happens with some mechanical failures? When electronics is working in
my opinion it still should be detected by bios and/or the system (win xp or
linux), but often it is not.
I could recover about 80% of the data from my HDD (which apparently has a
mechanical failure - plates spin up and down, heads create bad noises) if only
the disk could be seen by the system all the time. But often during copying of
the data heads hit with a loud sound so badly that sometimes even the plates
stop rotating, and the disk then dissapears from the system. It is then very
difficult to make it detectable by the system again, sometimes the sytem can
detect it but only after several minutes of copying it freezes and then
dissapears again.
Recently, I was unlucky, and even after several dozens of retries it's still
undetectable by the system.

Could you please advice what to do to make the disk detectable by the system
all the time?
What causes that it is not detectable although the failure is in mechanics not
electronics?

BTW, if someone has the same disk model (Quantum Fireball ST64A011), please
let me know.

andy

"andy" wrote in message
...
Hi!
Could someone please explain why in the case of *mechanical* failure HD
becomes sometimes undetected by BIOS and/or the operating system (e.g. win
xp
or linux)?

Consider the options available to the HD designer. What do you want the
user to see during POST about a HD that knows itself that it can't possibly
work. The HD designer knows that many BIOSs have no ability to detect and
display a HD error status during POST. The BIOS may only be able to report
'there' or 'not there'. If you were the HD designer would you want the HD
to report 'there' during POST even when the HD itself really knew that it
wasn't there? How would you answer the query of a poster in this NG who
wanted to know why a HD reported 'there' during post but was not there for
all intents and purposes for any booting steps after POST?

Did the HD designer make the correct design choice in the first place which
would likely cause a competent user to try another HD and assume that the HD
was dead dead which in fact it is?

If it was an electronic failure then such behaviour would be obious, but
why
the same happens with some mechanical failures? When electronics is
working in
my opinion it still should be detected by bios and/or the system (win xp
or
linux), but often it is not.

What on earth for? Such would be highly misleading and a very poor design
choice.

I could recover about 80% of the data from my HDD (which apparently has a
mechanical failure - plates spin up and down, heads create bad noises) if
only
the disk could be seen by the system all the time.

Huh?

But often during copying of
the data heads hit with a loud sound so badly that sometimes even the
plates
stop rotating, and the disk then dissapears from the system.

Duh!

It is then very
difficult to make it detectable by the system again, sometimes the sytem
can
detect it but only after several minutes of copying it freezes and then
dissapears again.
Recently, I was unlucky, and even after several dozens of retries it's
still
undetectable by the system.

Could you please advice what to do to make the disk detectable by the
system
all the time?
What causes that it is not detectable although the failure is in mechanics
not
electronics?

The drive is DOA!

BTW, if someone has the same disk model (Quantum Fireball ST64A011),
please
let me know.

"andy" wrote in message
...

Could you please advice what to do to make the disk detectable by the
system
all the time?
What causes that it is not detectable although the failure is in mechanics
not
electronics?


For recovery only;
I've had luck in the past by freezing dead hard drives, leave it over night
in the freezer, have everything ready on your pc, i.e. ide and power cables
loose so that you can plug it straight in and side panel off.

Plug the drive in as soon as it comes out the freezer and boot your pc,
don't bother fixing it into the case. You won't have long to recover your
data (if it works at all) so before trying the procedure, make a mental note
of what is most important to you on the drive and try and grab that first.
Don't expect to be able to recover a large amount of data using this method,
as the drive warms (quickly) you'll soon be back to the original problem.

Good luck, I bet you'll start backups now

HTH

--
Apollo

Thanks for your reply.

If it was an electronic failure then such behaviour would be obious, but
why
the same happens with some mechanical failures? When electronics is
working in
my opinion it still should be detected by bios and/or the system (win xp
or
linux), but often it is not.

What on earth for? Such would be highly misleading and a very poor design
choice.

But I could then recover 80% of my data, and now I can recover 0% of my data.
Does it make sense for you now?

Is there any way to disable that feature? (I mean to make the malfunctioned
HDD visible to the system again?)

The drive is DOA!

Don't get DOA.

a.

For recovery only;
I've had luck in the past by freezing dead hard drives, leave it over night
in the freezer, have everything ready on your pc, i.e. ide and power cables

Thanks for the advice, but I tried that already to no avail.

a.

"andy" wrote in message
...
Hi!
Could someone please explain why in the case of *mechanical* failure HD
becomes sometimes undetected by BIOS and/or the operating system (e.g. win
xp
or linux)?

*Sometimes* ... So, maybe it's the nature of the problem that prevents the
disk from being detected.

If it was an electronic failure then such behaviour would be obious, but
why
the same happens with some mechanical failures? When electronics is
working in
my opinion

It is hardly a matter of opinion ...

it still should be detected by bios and/or the system (win xp or
linux), but often it is not.
I could recover about 80% of the data from my HDD

How do you know? How did you come up with the 80%?

(which apparently has a
mechanical failure - plates spin up and down, heads create bad noises) if
only
the disk could be seen by the system all the time. But often during
copying of
the data heads hit with a loud sound so badly that sometimes even the
plates
stop rotating, and the disk then dissapears from the system. It is then
very
difficult to make it detectable by the system again, sometimes the sytem
can
detect it but only after several minutes of copying it freezes and then
dissapears again.

You should try to clone it as long as you can see it. However, every read
may worsen the condition of the disk, in general it is advised to cease DIY
recovery attempts (if the data is important to you) when a disk is maing
unusual and scary noises.

Recently, I was unlucky, and even after several dozens of retries it's
still
undetectable by the system.

Could you please advice what to do to make the disk detectable by the
system
all the time?

Your issue is a psychological one. You can not accept that there are
situations you can not resolve and have no control over. Apart from
contacting a data recovery lab, you also need to work out this problem.

BTW, if someone has the same disk model (Quantum Fireball ST64A011),
please
let me know.


Why do you want to know?

--
Joep

"andy" wrote in message
...

For recovery only;
I've had luck in the past by freezing dead hard drives, leave it over
night
in the freezer, have everything ready on your pc, i.e. ide and power
cables

Thanks for the advice, but I tried that already to no avail.

a.

You're out of luck then I'm afraid. If the data is that critical then don't
do anything else to it, contact a professional data recovery operation. Be
prepared to pay a lot of money (2nd mortgage) though, these people are not
cheap, and for good reason. They will probably strip your drive and mount
the physical disks in their own apparatus under clean room conditions - this
is what costs.

Or write it off to experience and learn from it. Do regular backups, and
remember backups are useless unless you test them and ensure they work.

--
Apollo

Or write it off to experience and learn from it. Do regular backups, and
remember backups are useless unless you test them and ensure they work.

I was doing backups of critical data, and that is why I'm not prepared to pay
a lot of $$$ for data recovery. :P
However, I'm prepared to pay a little bit for recovery of the rest of the
data. I think that if I could purchase another such disk even with bad
electronics, but with good mechanics, and then I could recover the data, even
if I open the disk not in a virtually dust free conditions.

a.

On Fri, 3 Sep 2004 11:24:48 +0200, "Joep" j o e p @ d i y d a t a r e c o v e
r y . n l wrote:

"andy" wrote in message
.. .

*Sometimes* ... So, maybe it's the nature of the problem that prevents the
disk from being detected.

Failure to mechanics seems to be the problem causing the non-detection
problem.
Unfortunatelly the "sometimes" is now "nearly always".

How do you know? How did you come up with the 80%?

When the disk was detectable then about 20% of files could not be read.
This was not because bad sectors (the disk did not have any AFAIK), but
because of the mechanics failure (when it started to have the symptoms of the
failure also 20% of data became unavailable).

You should try to clone it as long as you can see it. However, every read
may worsen the condition of the disk, in general it is advised to cease DIY
recovery attempts (if the data is important to you) when a disk is maing
unusual and scary noises.

Yes, it seems that the condition very quickly became much worse.

Your issue is a psychological one. You can not accept that there are
situations you can not resolve and have no control over. Apart from

How can I know that? If they designed it that way that it should not be
detectable when mechanics fails, then maybe also for the service purpose they
designed it also to be possible to disable that feature, making the disk
visible despite mechanical failure.
I hoped that someone knows how to disable that feature.

Why do you want to know?

If someone has such disk with bad electronics, but good mechanics, then I
could use the mechanics to recover my data. Just for one time recovery even
opening the disk in not sufficiently clean condition possibly could work.

a.

andy wrote:

Hi!
Could someone please explain why in the case of *mechanical* failure HD
becomes sometimes undetected by BIOS and/or the operating system (e.g. win xp
or linux)?
If it was an electronic failure then such behaviour would be obious, but why
the same happens with some mechanical failures? When electronics is working in
my opinion it still should be detected by bios and/or the system (win xp or
linux), but often it is not.
I could recover about 80% of the data from my HDD (which apparently has a
mechanical failure - plates spin up and down, heads create bad noises) if only
the disk could be seen by the system all the time. But often during copying of
the data heads hit with a loud sound so badly that sometimes even the plates
stop rotating, and the disk then dissapears from the system. It is then very
difficult to make it detectable by the system again, sometimes the sytem can
detect it but only after several minutes of copying it freezes and then
dissapears again.
Recently, I was unlucky, and even after several dozens of retries it's still
undetectable by the system.

Could you please advice what to do to make the disk detectable by the system
all the time?
What causes that it is not detectable although the failure is in mechanics not
electronics?

BTW, if someone has the same disk model (Quantum Fireball ST64A011), please
let me know.

andy


Maybe it stores part of its own software on the platters.

--
The e-mail address in our reply-to line is reversed in an attempt to
minimize spam. Our true address is of the form .