If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Correct Bios Settings -- Advanced Chipset Features -- GA-7N400 PRO2
System:
GA-7N400 PRO2 AMD Athlon XP 3000+ Barton 333MHZ fsb chip Two Kingston HyperX 512mb 184pin DDR 333 (pc 2700) Unbuffered memory Saphire Radeon 9600 Pro 256mb 19" Flat Panel Soundblaster Audigy2 160 gb Maxtor Drive DVD +R-R DVD ROM Multi Card Reader -- Internal Windows XP-HOME SP2 I am not sure what my settings should be under the Advanced Chipset Features menu. Should I have the System Performance Setting set to [Normal]? What should the FSB Frequency be set to? 100, 133, 166 or 200 If I have my motherboard set to Optimized Defaults, will this place my system in an Overclocked state? What should the AGP Frequency be set to? |
#2
|
|||
|
|||
"Jack" wrote in message ... System: GA-7N400 PRO2 AMD Athlon XP 3000+ Barton 333MHZ fsb chip Two Kingston HyperX 512mb 184pin DDR 333 (pc 2700) Unbuffered memory Saphire Radeon 9600 Pro 256mb 19" Flat Panel Soundblaster Audigy2 160 gb Maxtor Drive DVD +R-R DVD ROM Multi Card Reader -- Internal Windows XP-HOME SP2 I am not sure what my settings should be under the Advanced Chipset Features menu. Should I have the System Performance Setting set to [Normal]? Normal is fine for starters. What should the FSB Frequency be set to? 100, 133, 166 or 200 166mHz If I have my motherboard set to Optimized Defaults, will this place my system in an Overclocked state? No What should the AGP Frequency be set to? 66mHz Nice rig. Make sure the CLK_SW is ON ( auto) and set the CLK_RATIO switches to 6.5X. jps |
#3
|
|||
|
|||
"jpsga" wrote in message ... "Jack" wrote in message ... System: GA-7N400 PRO2 AMD Athlon XP 3000+ Barton 333MHZ fsb chip Two Kingston HyperX 512mb 184pin DDR 333 (pc 2700) Unbuffered memory Saphire Radeon 9600 Pro 256mb 19" Flat Panel Soundblaster Audigy2 160 gb Maxtor Drive DVD +R-R DVD ROM Multi Card Reader -- Internal Windows XP-HOME SP2 I am not sure what my settings should be under the Advanced Chipset Features menu. Should I have the System Performance Setting set to [Normal]? Normal is fine for starters. What should the FSB Frequency be set to? 100, 133, 166 or 200 166mHz If I have my motherboard set to Optimized Defaults, will this place my system in an Overclocked state? No What should the AGP Frequency be set to? 66mHz Nice rig. Make sure the CLK_SW is ON ( auto) and set the CLK_RATIO switches to 6.5X. jps Thanks for the response. Can you tell me why the CLK_RATIO switch should be set to 6.5x? I currently have it set to AUTO, all dip switches set to ON. |
#4
|
|||
|
|||
"jpsga" wrote in message ... "Jack" wrote in message ... System: GA-7N400 PRO2 AMD Athlon XP 3000+ Barton 333MHZ fsb chip Two Kingston HyperX 512mb 184pin DDR 333 (pc 2700) Unbuffered memory Saphire Radeon 9600 Pro 256mb 19" Flat Panel Soundblaster Audigy2 160 gb Maxtor Drive DVD +R-R DVD ROM Multi Card Reader -- Internal Windows XP-HOME SP2 I am not sure what my settings should be under the Advanced Chipset Features menu. Should I have the System Performance Setting set to [Normal]? Normal is fine for starters. What should the FSB Frequency be set to? 100, 133, 166 or 200 166mHz If I have my motherboard set to Optimized Defaults, will this place my system in an Overclocked state? No What should the AGP Frequency be set to? 66mHz Nice rig. Make sure the CLK_SW is ON ( auto) and set the CLK_RATIO switches to 6.5X. jps jps, The reason I asked about the 6.5x setting is because the number I thougt it should be set to is 13. Obviously 6.5 is 1/2 of 13, so what logic am I missing? Will it hurt to leave the CLK_RATIO at AUTO? |
#5
|
|||
|
|||
"Jack" wrote in message ... "jpsga" wrote in message ... "Jack" wrote in message ... System: GA-7N400 PRO2 AMD Athlon XP 3000+ Barton 333MHZ fsb chip Two Kingston HyperX 512mb 184pin DDR 333 (pc 2700) Unbuffered memory Saphire Radeon 9600 Pro 256mb 19" Flat Panel Soundblaster Audigy2 160 gb Maxtor Drive DVD +R-R DVD ROM Multi Card Reader -- Internal Windows XP-HOME SP2 I am not sure what my settings should be under the Advanced Chipset Features menu. Should I have the System Performance Setting set to [Normal]? Normal is fine for starters. What should the FSB Frequency be set to? 100, 133, 166 or 200 166mHz If I have my motherboard set to Optimized Defaults, will this place my system in an Overclocked state? No What should the AGP Frequency be set to? 66mHz Nice rig. Make sure the CLK_SW is ON ( auto) and set the CLK_RATIO switches to 6.5X. jps Thanks for the response. Can you tell me why the CLK_RATIO switch should be set to 6.5x? I currently have it set to AUTO, all dip switches set to ON. Ya got me!! My error S/B 166 *13=2158 so set to 13X not 6.5X. The 166MHz is set in the 'Advanced Chipset Features'. Now that you know how to clear the BIOS, you might try 13.5. A slight over clock from the specified 2167MHz. AUTO never worked for me, not sure why. jps |
#6
|
|||
|
|||
personally i would do 200 fsb with a memory at 83% or 166mHz and a 11x
multi to start with an psedo-xp3200+ this should get ya running "Jack" wrote in : System: GA-7N400 PRO2 AMD Athlon XP 3000+ Barton 333MHZ fsb chip Two Kingston HyperX 512mb 184pin DDR 333 (pc 2700) Unbuffered memory Saphire Radeon 9600 Pro 256mb 19" Flat Panel Soundblaster Audigy2 160 gb Maxtor Drive DVD +R-R DVD ROM Multi Card Reader -- Internal Windows XP-HOME SP2 I am not sure what my settings should be under the Advanced Chipset Features menu. Should I have the System Performance Setting set to [Normal]? What should the FSB Frequency be set to? 100, 133, 166 or 200 If I have my motherboard set to Optimized Defaults, will this place my system in an Overclocked state? What should the AGP Frequency be set to? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Bad Bios Flash or? | Ottar Tverberg | Asus Motherboards | 17 | May 23rd 05 04:05 PM |
IDE RAID- Major problem need to save my data | MC | General | 21 | December 5th 04 05:38 AM |
P4P800-E Deluxe Bios DRAM Settings no boot | Sascha Kiesewetter | Asus Motherboards | 9 | September 30th 04 07:53 AM |
BIOS flashing for different mobos with same chipset | Daveman750 | Overclocking | 4 | December 24th 03 03:01 PM |
Where are advanced BIOS settings on 8KNXP?? | Charlie Smith | Gigabyte Motherboards | 15 | September 3rd 03 12:21 AM |