If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
NewerTech make a product named Voyager Q to interface SATA drives to a host
by USB, Firewire, or eSATA. This is sometimes called a "drive toaster" because of the way you can mount a drive vertically into the enclosure without the need for any tray. Does anyone make something similar for a hotswap SCSI drive? It would be incredibly useful for forensics and the occasional drive backup to be able to just slip a hotswap SCSI drive into the vertical slot and hot plug it to the host. -- W |
#2
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
What is the need in this?
SCSI drives are much more expensive. So, you do the following: - turn off the enclosure - plug the usual SATA drive to it - turn on the enclosure - attach it to the host using USB, 1394 or eSATA. In eSATA case, you sometimes need to restart the host controller's driver using Windows Device Manager or the appropriate Linux/FreeBSD command line tools - go on -- Maxim S. Shatskih Windows DDK MVP http://www.storagecraft.com "W" wrote in message ... NewerTech make a product named Voyager Q to interface SATA drives to a host by USB, Firewire, or eSATA. This is sometimes called a "drive toaster" because of the way you can mount a drive vertically into the enclosure without the need for any tray. Does anyone make something similar for a hotswap SCSI drive? It would be incredibly useful for forensics and the occasional drive backup to be able to just slip a hotswap SCSI drive into the vertical slot and hot plug it to the host. -- W |
#3
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
"Maxim S. Shatskih" wrote in message
... What is the need in this? SCSI drives are much more expensive. I have existing servers that use SCSI drives. I want to make mirrors of those existing SCSI drives to identical SCSI drives for backups, without the hassle of having to prepare those backup drives into a hotswap tray, then remove them from the tray later. -- W "W" wrote in message ... NewerTech make a product named Voyager Q to interface SATA drives to a host by USB, Firewire, or eSATA. This is sometimes called a "drive toaster" because of the way you can mount a drive vertically into the enclosure without the need for any tray. Does anyone make something similar for a hotswap SCSI drive? It would be incredibly useful for forensics and the occasional drive backup to be able to just slip a hotswap SCSI drive into the vertical slot and hot plug it to the host. -- W |
#4
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
On Fri, 26 Nov 2010 19:33:59 -0800, "W"
wrote: "Maxim S. Shatskih" wrote in message ... What is the need in this? SCSI drives are much more expensive. I have existing servers that use SCSI drives. I want to make mirrors of those existing SCSI drives to identical SCSI drives for backups, without the hassle of having to prepare those backup drives into a hotswap tray, then remove them from the tray later. How often do you expect to do this and how many devices do you have to deal with? I have used one of the "internal" SCSI cables that came with an Adaptec 29160 to connect to the external connector of the card. I then used that connector on a SCSI drive that I put in a typical external SCSI disk box, but I didn't bother to use screws to fasten the drive in place and I didn't bother to put the covers back on the external box. This arrangement worked fine for backing up drives, but it wouldn't work in a data center environment where you can't leave loose pieces of hardware lying around. Also, stacking the external boxes was a bit iffy in terms of physical stability - electrically things worked OK. ALSO: I have tried several of those external SATA things where you just push the drive in and all of them resulted in drives running hot enough so that I jury-rigged a fan to blow over the drive. Again this resulted in an unstable physical arrangement that I wouldn't trust if other people had access to the area. (The heat probably wouldn't be a problem with SSDs.) You should also ask yourself why you don't want to mount the drive in a compact external box. For me the only reasons we 1. save space when I stored the disks that weren't online and 2. being able to temporarily be able to switch the location of with less work. For reason 1, I decided that it wasn't worth the effort since I would have to but the drives in foam for storage. For reason 2, I used the physically shaky arrangements above, but was nervous about knocking things over. |
#5
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
Here is an example of when I needed to mount a SCSI device on a host through
USB or eSATA. Today I had a Windows 2000 box that I needed to virtualize and bring over to a server. I can run the utility to turn the computer into a virtual machine image, but how do I get the files from this box to the destination. I have SCSI on the box and USB 1.0. Using USB 1.0, I can mount a SATA drive, but the conversion utility tells me it will take 17 hours to run. If I can use a SCSI device that cuts down to two hours. Assuming I target the files to a SCSI drive, once the conversion finishes, now I need to get those files over to the virtual server. What I would like to do is physically remove that SCSI device, attach it to an adapter to USB or eSATA, and then hot attach it to the virtual server. My application is simply getting quick connectivity to the drive, in order to transfer data. I have no requirements for any kind of enclosure, and this is not long term storage. Unfortunately, I don't have an easy path to using SCSI. So I'm stuck with a 17 hour job that will run to a SATA drive. -- W "Maxim S. Shatskih" wrote in message ... What is the need in this? SCSI drives are much more expensive. So, you do the following: - turn off the enclosure - plug the usual SATA drive to it - turn on the enclosure - attach it to the host using USB, 1394 or eSATA. In eSATA case, you sometimes need to restart the host controller's driver using Windows Device Manager or the appropriate Linux/FreeBSD command line tools - go on -- Maxim S. Shatskih Windows DDK MVP http://www.storagecraft.com "W" wrote in message ... NewerTech make a product named Voyager Q to interface SATA drives to a host by USB, Firewire, or eSATA. This is sometimes called a "drive toaster" because of the way you can mount a drive vertically into the enclosure without the need for any tray. Does anyone make something similar for a hotswap SCSI drive? It would be incredibly useful for forensics and the occasional drive backup to be able to just slip a hotswap SCSI drive into the vertical slot and hot plug it to the host. -- W |
#6
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
On Sun, 12 Dec 2010 00:22:13 -0800, "W"
wrote: Here is an example of when I needed to mount a SCSI device on a host through USB or eSATA. Today I had a Windows 2000 box that I needed to virtualize and bring over to a server. I can run the utility to turn the computer into a virtual machine image, but how do I get the files from this box to the destination. I have SCSI on the box and USB 1.0. Using USB 1.0, I can mount a SATA drive, but the conversion utility tells me it will take 17 hours to run. If I can use a SCSI device that cuts down to two hours. Assuming I target the files to a SCSI drive, once the conversion finishes, now I need to get those files over to the virtual server. What I would like to do is physically remove that SCSI device, attach it to an adapter to USB or eSATA, and then hot attach it to the virtual server. My application is simply getting quick connectivity to the drive, in order to transfer data. I have no requirements for any kind of enclosure, and this is not long term storage. Maybe you can do it with two converters, SCSI to IDE and IDE to SATA Here are a couple of SCSI to IDE. From Walmart, of all places, with links to a couple of other products http://www.walmart.com/ip/StarTech.c...i_sku=13214968 This allows use of IDE drive on SCSI controller, if I've read things correctly. The company also makes a IDE to SATA that allow use of SATA drives on IDE controllers. (I bought lots of stuff from them including some IDE to SATA adapters, but not the SCSI to IDE, but I haven't used the SSCI to IDE.) http://www.addonics.com/products/io/ide_scsi.asp Unfortunately, I don't have an easy path to using SCSI. So I'm stuck with a 17 hour job that will run to a SATA drive. -- W "Maxim S. Shatskih" wrote in message ... What is the need in this? SCSI drives are much more expensive. So, you do the following: - turn off the enclosure - plug the usual SATA drive to it - turn on the enclosure - attach it to the host using USB, 1394 or eSATA. In eSATA case, you sometimes need to restart the host controller's driver using Windows Device Manager or the appropriate Linux/FreeBSD command line tools - go on |
#7
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
On Sun, 12 Dec 2010 10:40:43 -0500, Mark F
wrote: On Sun, 12 Dec 2010 00:22:13 -0800, "W" wrote: Here is an example of when I needed to mount a SCSI device on a host through USB or eSATA. Today I had a Windows 2000 box that I needed to virtualize and bring over to a server. I can run the utility to turn the computer into a virtual machine image, but how do I get the files from this box to the destination. I have SCSI on the box and USB 1.0. Using USB 1.0, I can mount a SATA drive, but the conversion utility tells me it will take 17 hours to run. If I can use a SCSI device that cuts down to two hours. Assuming I target the files to a SCSI drive, once the conversion finishes, now I need to get those files over to the virtual server. What I would like to do is physically remove that SCSI device, attach it to an adapter to USB or eSATA, and then hot attach it to the virtual server. My application is simply getting quick connectivity to the drive, in order to transfer data. I have no requirements for any kind of enclosure, and this is not long term storage. Oops, I missed this one, which seems to do exactly what you want: Addonics ADSALVD160: http://www.addonics.com/products/io/adsalvd160.asp "Home Products I/O Converter SATA to SCSI Converter The SATA -SCSI converter instantly turns any fast low cost Serial ATA hard drive to a LVD160 SCSI hard drive. There is no driver to install and it works practically with any OS. The converter also supports SCSI performance up to Ultra LVD160 SCSI standard, ensuring maximum performance of the Serial ATA hard drive." NOTE: I can't find the product on the Addonics store; I'm not sure if the store is broken or my browser. Froogle finds it for about US$115 to US$130, but not at stores that I've dealt with. Maybe you can do it with two converters, SCSI to IDE and IDE to SATA Here are a couple of SCSI to IDE. From Walmart, of all places, with links to a couple of other products http://www.walmart.com/ip/StarTech.c...i_sku=13214968 This allows use of IDE drive on SCSI controller, if I've read things correctly. The company also makes a IDE to SATA that allow use of SATA drives on IDE controllers. (I bought lots of stuff from them including some IDE to SATA adapters, but not the SCSI to IDE, but I haven't used the SSCI to IDE.) http://www.addonics.com/products/io/ide_scsi.asp Unfortunately, I don't have an easy path to using SCSI. So I'm stuck with a 17 hour job that will run to a SATA drive. -- W "Maxim S. Shatskih" wrote in message ... What is the need in this? SCSI drives are much more expensive. So, you do the following: - turn off the enclosure - plug the usual SATA drive to it - turn on the enclosure - attach it to the host using USB, 1394 or eSATA. In eSATA case, you sometimes need to restart the host controller's driver using Windows Device Manager or the appropriate Linux/FreeBSD command line tools - go on |
#8
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
Buy a cheap SATA controller card (like low-end Promise) and SATA drive, install all of this to the w2k machine and go on.
-- Maxim S. Shatskih Windows DDK MVP http://www.storagecraft.com "W" wrote in message ... Here is an example of when I needed to mount a SCSI device on a host through USB or eSATA. Today I had a Windows 2000 box that I needed to virtualize and bring over to a server. I can run the utility to turn the computer into a virtual machine image, but how do I get the files from this box to the destination. I have SCSI on the box and USB 1.0. Using USB 1.0, I can mount a SATA drive, but the conversion utility tells me it will take 17 hours to run. If I can use a SCSI device that cuts down to two hours. Assuming I target the files to a SCSI drive, once the conversion finishes, now I need to get those files over to the virtual server. What I would like to do is physically remove that SCSI device, attach it to an adapter to USB or eSATA, and then hot attach it to the virtual server. My application is simply getting quick connectivity to the drive, in order to transfer data. I have no requirements for any kind of enclosure, and this is not long term storage. Unfortunately, I don't have an easy path to using SCSI. So I'm stuck with a 17 hour job that will run to a SATA drive. -- W "Maxim S. Shatskih" wrote in message ... What is the need in this? SCSI drives are much more expensive. So, you do the following: - turn off the enclosure - plug the usual SATA drive to it - turn on the enclosure - attach it to the host using USB, 1394 or eSATA. In eSATA case, you sometimes need to restart the host controller's driver using Windows Device Manager or the appropriate Linux/FreeBSD command line tools - go on -- Maxim S. Shatskih Windows DDK MVP http://www.storagecraft.com "W" wrote in message ... NewerTech make a product named Voyager Q to interface SATA drives to a host by USB, Firewire, or eSATA. This is sometimes called a "drive toaster" because of the way you can mount a drive vertically into the enclosure without the need for any tray. Does anyone make something similar for a hotswap SCSI drive? It would be incredibly useful for forensics and the occasional drive backup to be able to just slip a hotswap SCSI drive into the vertical slot and hot plug it to the host. -- W |
#9
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
"Mark F" wrote in message
... On Sun, 12 Dec 2010 10:40:43 -0500, Mark F wrote: On Sun, 12 Dec 2010 00:22:13 -0800, "W" wrote: Here is an example of when I needed to mount a SCSI device on a host through USB or eSATA. Today I had a Windows 2000 box that I needed to virtualize and bring over to a server. I can run the utility to turn the computer into a virtual machine image, but how do I get the files from this box to the destination. I have SCSI on the box and USB 1.0. Using USB 1.0, I can mount a SATA drive, but the conversion utility tells me it will take 17 hours to run. If I can use a SCSI device that cuts down to two hours. Assuming I target the files to a SCSI drive, once the conversion finishes, now I need to get those files over to the virtual server. What I would like to do is physically remove that SCSI device, attach it to an adapter to USB or eSATA, and then hot attach it to the virtual server. My application is simply getting quick connectivity to the drive, in order to transfer data. I have no requirements for any kind of enclosure, and this is not long term storage. Oops, I missed this one, which seems to do exactly what you want: Addonics ADSALVD160: http://www.addonics.com/products/io/adsalvd160.asp "Home Products I/O Converter SATA to SCSI Converter The SATA -SCSI converter instantly turns any fast low cost Serial ATA hard drive to a LVD160 SCSI hard drive. There is no driver to install and it works practically with any OS. The converter also supports SCSI performance up to Ultra LVD160 SCSI standard, ensuring maximum performance of the Serial ATA hard drive." That product converts a SATA drive into a SCSI drive. I'm doing the reverse: converting a SCSI drive into a SATA drive. -- W |
#10
|
|||
|
|||
External Drive Dock to Allow Hotswap SCSI to Attach by USB?
"Maxim S. Shatskih" wrote in message
... Buy a cheap SATA controller card (like low-end Promise) and SATA drive, install all of this to the w2k machine and go on. There were problems doing that but ultimately I did go that direction. -- W |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
IBM SCSI Hotswap LED Diagnostics | Yves Leclerc | Storage (alternative) | 1 | October 13th 05 06:45 AM |
Mystery SCSI Hotswap component. | [email protected] | Storage (alternative) | 0 | August 10th 05 10:30 PM |
Want: External removable [DOCK] Hard Drive | Dave_s | Storage (alternative) | 2 | June 8th 05 08:13 PM |
Where to buy external SCSI drive cases ? | Ftang Blobby | UK Computer Vendors | 1 | December 2nd 03 03:13 PM |