If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Connecting two fans to run of the one 12volt molex connection this possible ?
I've got 5 fans daisy chained to one controller knob, on my Zalman.
- We Live For The One We Die For The One stood up at show-n-tell, in , and said: Just is i'am getting a Vantec NXP-205-SL fan controler, but its only got 4 fan controlers on it. The two fans i want to link are my two rear exhast fans, as they should be working as ONE fan anyway. Just like to know, wish their was a plug that i could use, so i didn't have to do the wiring myself. Thanks. -- Strontium "It's no surprise, to me. I am my own worst enemy. `Cause every now, and then, I kick the livin' **** `outta me." - Lit |
#2
|
|||
|
|||
I take it it only has one knob ? If i have two connected to one knob on my Vantec Nexus, would that be ok, i think the maxium is 18watts for one knob I just want to connect 2 80mm fans to the one knob. Thanks. On Fri, 28 Nov 2003 10:48:43 -0600, "Strontium" wrote: I've got 5 fans daisy chained to one controller knob, on my Zalman. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: Just is i'am getting a Vantec NXP-205-SL fan controler, but its only got 4 fan controlers on it. The two fans i want to link are my two rear exhast fans, as they should be working as ONE fan anyway. Just like to know, wish their was a plug that i could use, so i didn't have to do the wiring myself. Thanks. |
#4
|
|||
|
|||
So what's connected to the other 3 knobs and two switches ? On Fri, 28 Nov 2003 12:19:18 -0600, "Strontium" wrote: It has 4 knobs + 2 switches. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: I take it it only has one knob ? If i have two connected to one knob on my Vantec Nexus, would that be ok, i think the maxium is 18watts for one knob I just want to connect 2 80mm fans to the one knob. Thanks. On Fri, 28 Nov 2003 10:48:43 -0600, "Strontium" wrote: I've got 5 fans daisy chained to one controller knob, on my Zalman. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: Just is i'am getting a Vantec NXP-205-SL fan controler, but its only got 4 fan controlers on it. The two fans i want to link are my two rear exhast fans, as they should be working as ONE fan anyway. Just like to know, wish their was a plug that i could use, so i didn't have to do the wiring myself. Thanks. |
#5
|
|||
|
|||
Just one Zalman CPU fan to another knob. Other two knobs and two switches
are empty. Started out this way because out of all the 4 to 3 pin adaptors I bought, only one worked (it was missing the speed sensor wire and the case fans are not equipped with sensors). But, I like this arrangement better because I only have to turn two knobs to go from quiet to jet-engine-loud. It would suck to have to turn 4 knobs and flick 2 switches, every time. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: So what's connected to the other 3 knobs and two switches ? On Fri, 28 Nov 2003 12:19:18 -0600, "Strontium" wrote: It has 4 knobs + 2 switches. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: I take it it only has one knob ? If i have two connected to one knob on my Vantec Nexus, would that be ok, i think the maxium is 18watts for one knob I just want to connect 2 80mm fans to the one knob. Thanks. On Fri, 28 Nov 2003 10:48:43 -0600, "Strontium" wrote: I've got 5 fans daisy chained to one controller knob, on my Zalman. - snip -- Strontium "It's no surprise, to me. I am my own worst enemy. `Cause every now, and then, I kick the livin' **** `outta me." - Lit |
#6
|
|||
|
|||
I suppose.
I'am thinking of getting the Vantec Nexus It lights up BLUE WOW. Its got all the cables, 4 of them, Big molex to micro molex converters, thats what i need, well for all my case fans, two rear, one front, and maybe a side, top and bottom fan, now that i know i can connect more than one to a knob But also i want to connect my Vid card fan and my CPU fan to a knob, the diagram i saw on the site, has a passthough cable to allow it to connect to the cpu fan, looks cool. Just got to figure out what fans to connect to what knobs. I was also thinking of hooking the fans upto on off swtiches as well, so i can turn all the fans off if i want, but not for the cpu fan, wont tempt fate their. I was thinking getting some of those fighter plane switches you know the ones you flick up to allow you access to the switch All i need is some audio mod that says STEALTH MODE ACTIVATED HE HE. Also some of those Knight rider Kit strobe lights and some neon lights, and i can have a REAL geek out of a pc. Ive already got my cordless, mouse and keyboard. Ive gone on TOOO much, time to stop,........... Someone please stop me. Bye. On Sat, 29 Nov 2003 02:31:53 -0600, "Strontium" wrote: Just one Zalman CPU fan to another knob. Other two knobs and two switches are empty. Started out this way because out of all the 4 to 3 pin adaptors I bought, only one worked (it was missing the speed sensor wire and the case fans are not equipped with sensors). But, I like this arrangement better because I only have to turn two knobs to go from quiet to jet-engine-loud. It would suck to have to turn 4 knobs and flick 2 switches, every time. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: So what's connected to the other 3 knobs and two switches ? On Fri, 28 Nov 2003 12:19:18 -0600, "Strontium" wrote: It has 4 knobs + 2 switches. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: I take it it only has one knob ? If i have two connected to one knob on my Vantec Nexus, would that be ok, i think the maxium is 18watts for one knob I just want to connect 2 80mm fans to the one knob. Thanks. On Fri, 28 Nov 2003 10:48:43 -0600, "Strontium" wrote: I've got 5 fans daisy chained to one controller knob, on my Zalman. - snip |
#7
|
|||
|
|||
just make sure the controller can take the combined wattage of the fans on
one port....... -- ______ From Adam Webb, Nick: Overlag www.tacticalgamer.com "We Live For The One We Die For The One" wrote in message ... I suppose. I'am thinking of getting the Vantec Nexus It lights up BLUE WOW. Its got all the cables, 4 of them, Big molex to micro molex converters, thats what i need, well for all my case fans, two rear, one front, and maybe a side, top and bottom fan, now that i know i can connect more than one to a knob But also i want to connect my Vid card fan and my CPU fan to a knob, the diagram i saw on the site, has a passthough cable to allow it to connect to the cpu fan, looks cool. Just got to figure out what fans to connect to what knobs. I was also thinking of hooking the fans upto on off swtiches as well, so i can turn all the fans off if i want, but not for the cpu fan, wont tempt fate their. I was thinking getting some of those fighter plane switches you know the ones you flick up to allow you access to the switch All i need is some audio mod that says STEALTH MODE ACTIVATED HE HE. Also some of those Knight rider Kit strobe lights and some neon lights, and i can have a REAL geek out of a pc. Ive already got my cordless, mouse and keyboard. Ive gone on TOOO much, time to stop,........... Someone please stop me. Bye. On Sat, 29 Nov 2003 02:31:53 -0600, "Strontium" wrote: Just one Zalman CPU fan to another knob. Other two knobs and two switches are empty. Started out this way because out of all the 4 to 3 pin adaptors I bought, only one worked (it was missing the speed sensor wire and the case fans are not equipped with sensors). But, I like this arrangement better because I only have to turn two knobs to go from quiet to jet-engine-loud. It would suck to have to turn 4 knobs and flick 2 switches, every time. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: So what's connected to the other 3 knobs and two switches ? On Fri, 28 Nov 2003 12:19:18 -0600, "Strontium" wrote: It has 4 knobs + 2 switches. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: I take it it only has one knob ? If i have two connected to one knob on my Vantec Nexus, would that be ok, i think the maxium is 18watts for one knob I just want to connect 2 80mm fans to the one knob. Thanks. On Fri, 28 Nov 2003 10:48:43 -0600, "Strontium" wrote: I've got 5 fans daisy chained to one controller knob, on my Zalman. - snip |
#8
|
|||
|
|||
How many watts does a normal 80mm fan do ??? On Sun, 30 Nov 2003 02:33:11 -0000, "Adam Webb" wrote: just make sure the controller can take the combined wattage of the fans on one port....... |
#9
|
|||
|
|||
Usually, around 0.5Amp (x12V = 6Watts)
Anyway, I don't think this applies. If it did, my controller would be toast right now (5 fans, would be about 25-30Watts on one channel!). I don't believe that the Wattages combine to make a 'grand total' except where the PSU is concerned. Been awhile since I took physics. But, I don't think it's cumulative. More, rather, what ever the highest wattage in the chain is. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: How many watts does a normal 80mm fan do ??? On Sun, 30 Nov 2003 02:33:11 -0000, "Adam Webb" wrote: just make sure the controller can take the combined wattage of the fans on one port....... -- Strontium "It's no surprise, to me. I am my own worst enemy. `Cause every now, and then, I kick the livin' **** `outta me." - Lit |
#10
|
|||
|
|||
I would only connect 2 or maybe three to any one anyway, so i'am not in any trouble. Thanks. On Mon, 1 Dec 2003 06:59:41 -0600, "Strontium" wrote: Usually, around 0.5Amp (x12V = 6Watts) Anyway, I don't think this applies. If it did, my controller would be toast right now (5 fans, would be about 25-30Watts on one channel!). I don't believe that the Wattages combine to make a 'grand total' except where the PSU is concerned. Been awhile since I took physics. But, I don't think it's cumulative. More, rather, what ever the highest wattage in the chain is. - We Live For The One We Die For The One stood up at show-n-tell, in , and said: How many watts does a normal 80mm fan do ??? On Sun, 30 Nov 2003 02:33:11 -0000, "Adam Webb" wrote: just make sure the controller can take the combined wattage of the fans on one port....... |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fans and operating voltage | Flierbk | General | 3 | September 22nd 04 06:34 AM |
intel board, fans on during standby. intel d875PBZ. | JohnJ | General | 0 | January 13th 04 05:14 PM |
Silent Computer - Advice | David Taylor | General | 49 | October 7th 03 11:26 AM |
Fan Controller and Fan causes floppy drive failure | Andrew Diamond | Overclocking | 25 | September 19th 03 07:51 AM |
Sleeve bearing fans | Adrian | General | 6 | August 2nd 03 01:14 AM |