If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Loud compaq Proliant DL580 (gen1)
Any ways of either running the fans at lower speeds (I was thinking about
lowering voltage, since stopping the fans would cause a shutdown) That machine will be in a rack, along with my switch, UPS and a home-made disk array. So it doesn't need jet-engine fans to cool those 4 poor Xeons. (700Mhz) I couldn't find any *software* ways to lower the fans, thus stopping them from sounding like a shop-vac. If I owned a hose, the machine would be in the basement, in its own room. Problem is I'm renting an appartment, and my concern is that racket (besides keeping me up and getting my cat crazy) will drive the neigboors nuts. I'm about to build a simple circuit mimmicking the fan's rotations (555 or something akin) and use my own cooling solution... -- (\_ _/) (='.'=) This is Bunny. Copy and paste bunny into your (")_(") signature to help him gain world domination. |
#2
|
|||
|
|||
Loud compaq Proliant DL580 (gen1)
"El Bandito" wrote Any ways of either running the fans at lower speeds (I was thinking about lowering voltage, since stopping the fans would cause a shutdown) That machine will be in a rack, along with my switch, UPS and a home-made disk array. So it doesn't need jet-engine fans to cool those 4 poor Xeons. (700Mhz) I couldn't find any *software* ways to lower the fans, thus stopping them from sounding like a shop-vac. If I owned a hose, the machine would be in the basement, in its own room. Problem is I'm renting an appartment, and my concern is that racket (besides keeping me up and getting my cat crazy) will drive the neigboors nuts. I'm about to build a simple circuit mimmicking the fan's rotations (555 or something akin) and use my own cooling solution... Do you have the fully redundant fan and power supply options? If you do, you should find that it runs quieter than with the non-redundant fan configuration. Failing that, I'd suggest you isolate your rack accoustically. I would not start to tamper with the innards of a proliant - you'll mess up the monitoring. |
#3
|
|||
|
|||
Loud compaq Proliant DL580 (gen1)
"Jez T" wrote in message ... "El Bandito" wrote Any ways of either running the fans at lower speeds (I was thinking about lowering voltage, since stopping the fans would cause a shutdown) That machine will be in a rack, along with my switch, UPS and a home-made disk array. So it doesn't need jet-engine fans to cool those 4 poor Xeons. (700Mhz) I couldn't find any *software* ways to lower the fans, thus stopping them from sounding like a shop-vac. If I owned a hose, the machine would be in the basement, in its own room. Problem is I'm renting an appartment, and my concern is that racket (besides keeping me up and getting my cat crazy) will drive the neigboors nuts. I'm about to build a simple circuit mimmicking the fan's rotations (555 or something akin) and use my own cooling solution... Do you have the fully redundant fan and power supply options? If you do, you should find that it runs quieter than with the non-redundant fan configuration. That's quieter? I'd hate to hear the loud version Failing that, I'd suggest you isolate your rack accoustically. That's what I thought... I would not start to tamper with the innards of a proliant - you'll mess up the monitoring. THe only monitoring seems to be ... A- the fans are present B- They're running No speed control whatsoever. I don't think it needs to sound like a 747 at take off to cool 4 700Mhz Xeons. (especially when I look at the huge integral heatsinks on them) Thanks... |
#4
|
|||
|
|||
Loud compaq Proliant DL580 (gen1)
"El Bandito" wrote No speed control whatsoever. I don't think it needs to sound like a 747 at take off to cool 4 700Mhz Xeons. (especially when I look at the huge integral heatsinks on them) These things are designed to run a optimum reliability on a server room, not quietly in an appartment. They do what they are dedigned to do... Try: alt.sys.pc-clone.compaq.servers for support on this thing. You get better help that just I can give you. |
#5
|
|||
|
|||
Loud compaq Proliant DL580 (gen1)
"Jez T" wrote in message ... "El Bandito" wrote Any ways of either running the fans at lower speeds (I was thinking about lowering voltage, since stopping the fans would cause a shutdown) That machine will be in a rack, along with my switch, UPS and a home-made disk array. So it doesn't need jet-engine fans to cool those 4 poor Xeons. (700Mhz) I couldn't find any *software* ways to lower the fans, thus stopping them from sounding like a shop-vac. If I owned a hose, the machine would be in the basement, in its own room. Problem is I'm renting an appartment, and my concern is that racket (besides keeping me up and getting my cat crazy) will drive the neigboors nuts. I'm about to build a simple circuit mimmicking the fan's rotations (555 or something akin) and use my own cooling solution... Do you have the fully redundant fan and power supply options? If you do, you should find that it runs quieter than with the non-redundant fan configuration. Failing that, I'd suggest you isolate your rack accoustically. I would not start to tamper with the innards of a proliant - you'll mess up the monitoring. Yes, they are noisy, and rather impossible to use them in the same room unless you are deaf. Your 555 trick could simulate the fan rotation, given the time to work out an interface to them. In the dl580, I believe it has 5 sets of fans plus the fan in each of the power supplies. That is defiantly overkill on Compaq's part but under heavy load and high ambient temperature it's possible it could be needed. My beef with those units is the current (electricity) the fans pull. Most all Compaq's are energy wasters and fans seem to be the bulk of it. Cooling is mandatory but I have wondered if a proportional speed control based on temperature would not save a ton of electricity. Some time ago I modified 10 Compaq UPS's that has 155 watt (120VAC) fans. As they were, the fans were as noisy as the dl580 and ran full bore all the time. I now run them at a reduced voltage pulling about 40 watts each. I used a thermistor to detect heat on the heat-sinks and when it rises a relay switches fans to full power. About the only time they kick into high gear is when it's running on battery and then when it's charging the batteries at a heavy rate. 115 watts X 10, that's 1150 watts I am saving there alone. I've been using them that way for about two years now. Now look at it money wise, that's about 828 KWh per month saved @ .10 per KWh that's 83 bucks a month saved there alone. Bottom Line, not because of noise, but energy costs; I have thought of designing a circuit that would control the server fans proportionally, based on temperature. I would bet I could cut the energy costs drastically. It may be worthwhile to try it and check the power savings. That would also reduce your noise, but in my case I have a room of servers so the noise is immaterial to me. Oh, if anyone out there has tried this trick please chime in. I would love to hear about it. Phil |
#6
|
|||
|
|||
Loud compaq Proliant DL580 (gen1)
"Phil" wrote in message . .. unless you are deaf. Your 555 trick could simulate the fan rotation, given the time to work out an interface to them. In the dl580, I believe it has 5 .... Oh, if anyone out there has tried this trick please chime in. I would love to hear about it. I'll probably do it, hadn't thought about the energy consumption alone. For example, the double set in front of the PCI air tunnel (for the hot swap cards) is not needed, as they are currently empty (the slots) And 2 front + 1 rear double-fan sets for cooling four poor little 700 processors? *WAY* overkill. My overclocked Barton runs on air (2500+ mobile at 2.5 GHZ), not even a high-end cooler. And that CPU heats lots more than those xeons. Phil |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
FS PRINTER PARTS trays fusers drums printheads -- oki fujitsu hp genicom epson ibm dec jetdirect laserjet lexnmark qms okidata ml320 mannesmann tally printonix tektronix qms toshiba zebra otc ibm lexmark intermec dec compaq montreal canada toronto o | [email protected] | Printers | 1 | May 29th 05 07:18 PM |
FS PRINTER PARTS trays fusers drums printheads -- oki fujitsu hp genicom epson ibm dec jetdirect laserjet lexnmark qms okidata ml320 mannesmann tally printonix tektronix qms toshiba zebra otc ibm lexmark intermec dec compaq montreal canada toronto o | [email protected] | Printers | 1 | March 15th 05 05:50 AM |
Compaq user diagnostics diskette | bananaboat | Compaq Computers | 3 | April 21st 04 03:05 AM |
FS: Qty. 11 Compaq Proliant Systems $1,500 - 3000, 4500, 5500's | 444UNIX | Compaq Computers | 0 | November 3rd 03 02:29 PM |
Compaq ready to go | Jazzy Ban | Compaq Computers | 0 | October 14th 03 02:54 PM |