If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
How to set AP400 to continue running after power disturbance?
I want my AP400 Compaq Workstation to automaticaly turn on again
after the power failure. Currently, when the power comes back, the computer does not start - even if it was running before the failure. I have to manually press the power button to start it again. I have read in the manuals that it is possible to set such option on the Advanced tab in the Setup. Unfortunately I have no 'Advanced' options in my workstations setup. This Windows 3.1-like BIOS is quite limited, I would say... I have most recent BIOS and setup versions: 99.07.14 and 1.19.001 respectively. Is there any possibility to access this option in the setup? What should I do? Or is it possible to set using some other utility? Please help me, since I cannot find this information anywhere. thanks in advance Bartek |
#2
|
|||
|
|||
How to set AP400 to continue running after power disturbance?
Why not get a UPS? The Uninterruptable Power Supply likely is the only way
to achieve what you are seeking. HH wrote in message oups.com... I want my AP400 Compaq Workstation to automaticaly turn on again after the power failure. Currently, when the power comes back, the computer does not start - even if it was running before the failure. I have to manually press the power button to start it again. I have read in the manuals that it is possible to set such option on the Advanced tab in the Setup. Unfortunately I have no 'Advanced' options in my workstations setup. This Windows 3.1-like BIOS is quite limited, I would say... I have most recent BIOS and setup versions: 99.07.14 and 1.19.001 respectively. Is there any possibility to access this option in the setup? What should I do? Or is it possible to set using some other utility? Please help me, since I cannot find this information anywhere. thanks in advance Bartek |
#3
|
|||
|
|||
How to set AP400 to continue running after power disturbance?
Yes, an UPS I do have. But the power failures are sometimes longer than
the UPS can survive.. /B HH wrote: Why not get a UPS? The Uninterruptable Power Supply likely is the only way to achieve what you are seeking. HH wrote in message oups.com... I want my AP400 Compaq Workstation to automaticaly turn on again after the power failure. Currently, when the power comes back, the computer does not start - even if it was running before the failure. I have to manually press the power button to start it again. I have read in the manuals that it is possible to set such option on the Advanced tab in the Setup. Unfortunately I have no 'Advanced' options in my workstations setup. This Windows 3.1-like BIOS is quite limited, I would say... I have most recent BIOS and setup versions: 99.07.14 and 1.19.001 respectively. Is there any possibility to access this option in the setup? What should I do? Or is it possible to set using some other utility? Please help me, since I cannot find this information anywhere. thanks in advance Bartek |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
24 pin power supplies, stability issues? | Don Burnette | AMD x86-64 Processors | 32 | April 21st 06 12:14 PM |
x800xl and Far Cry, disasterous! | AAvK | Nvidia Videocards | 38 | October 14th 05 01:42 PM |
Can I fabricate my own USB power cable? | Bryan Ischo | General Hardware | 5 | September 12th 04 10:58 AM |
Happy Birthday America | SST | Overclocking | 333 | November 27th 03 07:54 PM |
Happy Birthday America | SST | Overclocking AMD Processors | 326 | November 27th 03 07:54 PM |