|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
October 6th 05, 11:07 PM
|
|||
|
|||
NF7-S V2 Alarm goes on then shut Down
My system started freezing so I notice high temps 45 to 50, I decided to
blow out all the dust and put some AS5 on my cpu and put back my heatsink and fan , when I turn on my system it powered up then an alarm came on and shut down the system, the alarm just stays on, Does any one have any idea. 
|
|
#2
October 7th 05, 06:03 PM
|
|||
|
|||
|
you may have to reset values to default in abiteq
"Miller1236" wrote in message ... My system started freezing so I notice high temps 45 to 50, I decided to blow out all the dust and put some AS5 on my cpu and put back my heatsink and fan , when I turn on my system it powered up then an alarm came on and shut down the system, the alarm just stays on, Does any one have any idea.
|
|
#3
October 7th 05, 07:21 PM
|
|||
|
|||
|
On Thu, 6 Oct 2005 17:07:11 -0500, "Miller1236"
had a flock of green cheek conures squawk out: My system started freezing so I notice high temps 45 to 50, I decided to blow out all the dust and put some AS5 on my cpu and put back my heatsink and fan , when I turn on my system it powered up then an alarm came on and shut down the system, the alarm just stays on, Does any one have any idea. CPU fan plugged into the correct header? CPU heatsink properly installed? Stephen --
|
|
#4
October 7th 05, 11:14 PM
|
|||
|
|||
|
Hi, what would happen if my CPU get to much AS5 on it, would it
cause the cpu not to work, it power up but then shuts down and the alarm sound off. Fan ,chip and heatsink installed properly. Could something happen to the board, when I was removing heatsink with my srew driver I accidently hit my board , would this cause the proplem.. Thanks, Miller "Stephen" wrote in message news  On Thu, 6 Oct 2005 17:07:11 -0500, "Miller1236" had a flock of green cheek conures squawk out: My system started freezing so I notice high temps 45 to 50, I decided to blow out all the dust and put some AS5 on my cpu and put back my heatsink and fan , when I turn on my system it powered up then an alarm came on and shut down the system, the alarm just stays on, Does any one have any idea. CPU fan plugged into the correct header? CPU heatsink properly installed? Stephen --
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Windows XP SP2 Shut down problem | John Johnson | Homebuilt PC's | 9 | November 11th 04 05:33 AM |
| Cable Modem not allowing computer to shut down | Anton | General Hardware | 2 | August 2nd 04 11:18 PM |
| Shut down problems after installing Win2K... | XXX | Homebuilt PC's | 4 | February 18th 04 07:54 AM |
| No POST only FF alarm on boot | John Smith | Homebuilt PC's | 3 | February 4th 04 03:20 PM |
| Need very loud alarm clock - Nokia 6210 won't do! [O/T] | Boc© | UK Computer Vendors | 13 | November 17th 03 02:11 PM |
Linear Mode
