If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Choosing motherboard Compaq 5301
Need new motherboard. I'm happy with the service I got from my present
motherboard. I contacted HP about upgrading the CPU and they said yes but only to about 800megs which is not enough it has to be 2.0Gs or better. My present board has on board video and audio. Tiger Direct has a motherboard a Mach Speed P4MDPT which seem like an ideal replacement for me. Is there some way to know if this board will fit my mini-tower? Sales at Tiger Direct would not commit and I don't blame them. |
#2
|
|||
|
|||
Donald writes:
Need new motherboard. I'm happy with the service I got from my present motherboard. I contacted HP about upgrading the CPU and they said yes but only to about 800megs which is not enough it has to be 2.0Gs or better. My present board has on board video and audio. Tiger Direct has a motherboard a Mach Speed P4MDPT which seem like an ideal replacement for me. Is there some way to know if this board will fit my mini-tower? Sales at Tiger Direct would not commit and I don't blame them. Manufacturers like Compaq tend to use proprietary hardware. Besides the motherboard upgrade, you've got to think about other components like the power supply, RAM, and etc. I've got an old Dell at home (given to me) that has a proprietary power supply and case connections (for power, reset, and etc.). I'd recommend going for a new case (with power supply), motherboard, sound, video, and etc. Possibly you could re-use your drives (the floppy may be proprietary), but they likely won't be as big and/or fast as today's drives. RAM may be too old to be re-used, so check that before you commit to an "upgrade". When all is said and done, you may be better off buying or building an entirely new computer and re-using your external peripherals (keyboard, mouse, monitor, printer, and the like). Jeff -- Remove "no" and "spam" from email address to reply. If it says "This is not spam!", it's surely a lie. |
#3
|
|||
|
|||
"Donald" wrote in message nk.net... Need new motherboard. I'm happy with the service I got from my present motherboard. I contacted HP about upgrading the CPU and they said yes but only to about 800megs which is not enough it has to be 2.0Gs or better. My present board has on board video and audio. Tiger Direct has a motherboard a Mach Speed P4MDPT which seem like an ideal replacement for me. Is there some way to know if this board will fit my mini-tower? Sales at Tiger Direct would not commit and I don't blame them. because that board is a microATX form factor it should fit in your mini tower without a problem. *however* just have a close look at the picture of the board to get an idea where the cpu will be...relative to your powersupply. if the cpu ends up directly under your powersupply ...a cpu cooler larger than your present one (which may be required) may end up with too little air flow... and you'd need a taller case. |
#4
|
|||
|
|||
If you are upgrading the motherboard from less than 800MHz to ~2GHz, if
you're planning on getting an Intel P4 CPU you will also need a new P4 capable power supply unit. Your Compaq case will probably NOT take a standard size PSU; most proprietary vendors use non-standard sized power supply units and sometimes motherboards. -- DaveW "Donald" wrote in message nk.net... Need new motherboard. I'm happy with the service I got from my present motherboard. I contacted HP about upgrading the CPU and they said yes but only to about 800megs which is not enough it has to be 2.0Gs or better. My present board has on board video and audio. Tiger Direct has a motherboard a Mach Speed P4MDPT which seem like an ideal replacement for me. Is there some way to know if this board will fit my mini-tower? Sales at Tiger Direct would not commit and I don't blame them. |
#5
|
|||
|
|||
Thank you everyone for your input. The capacity of my power supply gives
me some doubt, but I have decided to swap out my boards and check the results. I have, since my posting, learned that the Compaq board and the Mach Speed board are integrated motherboards and that was the deciding factor for me to give it a try. Donald wrote: Need new motherboard. I'm happy with the service I got from my present motherboard. I contacted HP about upgrading the CPU and they said yes but only to about 800megs which is not enough it has to be 2.0Gs or better. My present board has on board video and audio. Tiger Direct has a motherboard a Mach Speed P4MDPT which seem like an ideal replacement for me. Is there some way to know if this board will fit my mini-tower? Sales at Tiger Direct would not commit and I don't blame them. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Compaq Laptop Parts for Sale... | Valueplay | General | 0 | February 19th 05 04:56 AM |
Choosing an ATX case and P4 motherboard | Mals | General | 15 | August 8th 04 06:14 PM |
AGP Voltage problem | John | Overclocking | 4 | February 29th 04 10:51 AM |
Help: Need Motherboard Info Inside Old Compaq | Darren Harris | Homebuilt PC's | 12 | December 22nd 03 10:56 PM |
Advice needed on Choosing a Motherboard and CPU | ashertece | General | 2 | August 23rd 03 05:16 PM |