A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » Processors » Overclocking
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

2,4@3,2 HELP: PCI 1 (1h) : PCI 32-bit 5V 3.3V PME HalfLength Available/AGP (7h) : AGP-4x 32-bit 3.3V PME HalfLength InUse



 
 
Thread Tools Display Modes
  #1  
Old January 17th 04, 03:01 AM
N´far
external usenet poster
 
Posts: n/a
Default 2,4@3,2 HELP: PCI 1 (1h) : PCI 32-bit 5V 3.3V PME HalfLength Available/AGP (7h) : AGP-4x 32-bit 3.3V PME HalfLength InUse

Pls help:
20 to 30% performance increase here, but...

Stabile at 2D, but drops to desktop after about 1 minute or 2 at 3D (PC
mark2001 or CoD) .
Since FBS 133 FBS ( before 100 ) I can´t see any PCI or AGP bus speeds
anymore with prgs. I´m quite sure, could see PCI or AGP bus speeds before
changing to 133...


SiSoftware Sandra says:


System Chassis
Manufacturer : Chassis Manufacture
Case Type : Tower
Can be locked : No
Version : Chassis Version
Serial Number : Chassis Serial Number
Asset Tag Number : Asset-1234567890
Boot-up State : Safe
Power State : Safe
Thermal State : Safe

System Mainboard
Manufacturer : ASUSTeK Computer INC.
MP Support : No
Model : P4B266
Version : REV 2.xx
Serial Number : xxxxxxxxxxx
BIOS ID : 08/06/2002--I845--P4B266

System Memory Controller
Location : Mainboard
Error Correction Capability : None
Number of Memory Slots : 3
Maximum Installable Memory : 2GB
Bank 1 - DIMM 1 : DIMM Synchronous DRAM 256MB/72
Bank 2 - DIMM 2 : DIMM Synchronous DRAM 256MB/72
Bank 3 - DIMM 3 : Empty

System Chipset
Model : ASUSTeK Computer Inc 82845/E/MP/MZ Brookdale CPU to I/O Bridge
Bus(es) : AGP PCI IMB USB SMBus/i2c
Front Side Bus Speed : 4x 133MHz (532MHz data rate)
Max FSB Speed / Max Memory Speed : 4x 100MHz / 2x 133MHz
In Order Queue Depth : 12 req(s)

Chipset Hub Interface
Type : HubInterface
Version : 1.00
No. Ports : 1
Width : 8-bit
Full Duplex : Yes
Multiplier : 1x

APIC 1
Version : 2.00
Multiplier : 1/2x
Max Interrupts : 24
IRQ Handler Engaged : Yes
Enhanced Support : Yes

Logical/Chipset Memory Banks
Bank 0 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
Bank 1 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
Bank 2 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
Bank 3 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL


-------------- hmm.... got 2x 128 PC2100 installed.... :-(


Speed : 2x 133MHz (266MHz data rate)
Multiplier : 1x
Refresh Rate : 15.60µs
Power Down Mode : No
Fixed Hole Present : No

System Clock Generator
Model : ICS 950209
Software Programmable : No
Read-Back Support : Yes

Environment Monitor 1
Model : Asus ASB100 SMB
Version : 3.01
Mainboard Specific Support : No

Temperature Sensor(s)
Board Temperature : 23.0°C / 73.4°F
CPU Temperature : 32.0°C / 89.6°F
Power / Aux Temperature : 127.0°C / 260.6°F

Cooling Device(s)
Auto Fan Speed Control : No
CPU Fan Speed : 2265rpm

Voltage Sensor(s)
CPU Core Voltage : 1.71V
Aux Voltage : 1.71V
+3.3V Voltage : 3.33V
+5V Voltage : 5.05V
+12V Voltage : 11.25V
-12V Voltage : -11.75V
-5V Voltage : -4.93V

AGP Bus
Version : 2.00
Current Data Transfer Rate : 4x
Side Band Enabled : Yes
Fast-Writes Enabled : Yes
Aperture Size : 128MB

PCI Bus(es)
Version : 2.20
No Bridges : 2
PCI Bus 0 : 32-bit PCI (1x PCIClk)
PCI Bus 2 : 32-bit PCI (1x PCIClk)

LPC Hub Controller 1
Model : Intel Corporation 82801BA (ICH2) LPC Interface Controller
ACPI PM Enabled : Yes
Random Number Generator Enabled : No
Random Number Generator Support : Yes

USB Controller 1
Model : Intel Corporation 82801BA/BAM (ICH2) USB Universal Host Controller
Version : 1.10
UHCI Interface : Yes
Channels : 2
Speed : 48MHz
Legacy Emulation Enabled : No

USB Controller 2
Model : Intel Corporation 82801BA/BAM (ICH2) USB Universal Host Controller
Version : 1.10
UHCI Interface : Yes
Channels : 2
Speed : 48MHz
Legacy Emulation Enabled : No

System SMBus Controller 1
Model : Intel 801xx SMBus
Version : 0.05
Speed : 16kHz

Expansion Slot(s)
PCI 1 (1h) : PCI 32-bit 5V 3.3V PME HalfLength Available (Intel Corporation
82845/E/MP/MZ Brookdale CPU to AGP Bridge)
PCI 2 (2h) : PCI 32-bit 5V 3.3V PME HalfLength Available
PCI 3 (3h) : PCI 32-bit 5V 3.3V PME HalfLength Available
PCI 4 (4h) : PCI 32-bit 5V 3.3V PME HalfLength Available
PCI 5 (5h) : PCI 32-bit 5V 3.3V PME HalfLength InUse
PCI 6 (6h) : PCI 32-bit 5V 3.3V PME HalfLength Available
AGP (7h) : AGP-4x 32-bit 3.3V PME HalfLength InUse

Port Connector(s)
PRIMARY IDE/HDD : None - ATA / None
SECONDARY IDE/HDD : None - ATA / None
FLOPPY : None - Floppy / None
USB1 : USB - None / USB
USB2 : USB - None / USB
USB3 : USB - None / USB
USB4 : USB - None / USB
PS/2 Keyboard : Keyboard Port - None / PS/2
PS/2 Mouse : Mouse Port - None / PS/2
Parallel Port : Parallel Port ECP/EPP - None / DB25 pin female
Serial Port 1 : Serial Port 16550 Compatible - None / DB-9 pin male
Serial Port 2 : Serial Port 16550 Compatible - None / DB-9 pin male
Joystick Port : Joystick Port - None / DB-15 pin female
MIDI Port : MIDI Port - None / DB-15 pin female
Line In Jack : Audio Port - None / Mini-jack
Headphone : Audio Port - None / Mini-jack
Microphone : Audio Port - None / Mini-jack
Video Port : Video Port - None / Mini-jack




  #2  
Old January 17th 04, 05:16 AM
N´far
external usenet poster
 
Posts: n/a
Default


"N´far" skrev i en meddelelse
. ..
Stabile at 2D, but drops to desktop after about 1 minute or 2 at 3D (PC
mark2001 or CoD) .
Since FBS 133 FBS ( before 100 ) I can´t see any PCI or AGP bus speeds
anymore with prgs. I´m quite sure, could see PCI or AGP bus speeds before
I changed to 133FBS...


Boot-up State : Safe
Power State : Safe
Thermal State : Safe
Model : P4B266
BIOS ID : 08/06/2002--I845--P4B266
Number of Memory Slots : 3
Maximum Installable Memory : 2GB
Bank 1 - DIMM 1 : DIMM Synchronous DRAM 256MB/72
Bank 2 - DIMM 2 : DIMM Synchronous DRAM 256MB/72
Bank 3 - DIMM 3 : Empty
Model : ASUSTeK Computer Inc 82845/E/MP/MZ Brookdale CPU to I/O Bridge
Bus(es) : AGP PCI IMB USB SMBus/i2c
Front Side Bus Speed : 4x 133MHz (532MHz data rate)
Max FSB Speed / Max Memory Speed : 4x 100MHz / 2x 133MHz
In Order Queue Depth : 12 req(s)
Chipset Hub Interface
Type : HubInterface
Version : 1.00
No. Ports : 1
Width : 8-bit
Full Duplex : Yes
Multiplier : 1x
APIC 1
Version : 2.00
Multiplier : 1/2x
Max Interrupts : 24
IRQ Handler Engaged : Yes
Enhanced Support : Yes
Logical/Chipset Memory Banks
Bank 0 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
Bank 1 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
Bank 2 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL
Bank 3 Setting : 128MB DDR-SDRAM 8-1-1-1R 6-1-1-1W 2.5-3-3CL

**************' -------------- hmm.... got 2x 128 PC2100
installed.... :-(
Speed : 2x 133MHz (266MHz data rate)
Multiplier : 1x
Refresh Rate : 15.60µs
Power Down Mode : No
Fixed Hole Present : No
System Clock Generator
Model : ICS 950209
Software Programmable : No
Read-Back Support : Yes
Environment Monitor 1
Model : Asus ASB100 SMB
Version : 3.01
Mainboard Specific Support : No
Temperature Sensor(s)
Board Temperature : 23.0°C / 73.4°F
CPU Temperature : 32.0°C / 89.6°F
Power / Aux Temperature : 127.0°C / 260.6°F
Cooling Device(s)
Auto Fan Speed Control : No
CPU Fan Speed : 2265rpm
Voltage Sensor(s)
CPU Core Voltage : 1.71V
Aux Voltage : 1.71V
+3.3V Voltage : 3.33V
+5V Voltage : 5.05V
+12V Voltage : 11.25V
-12V Voltage : -11.75V
-5V Voltage : -4.93V
AGP Bus
Version : 2.00
Current Data Transfer Rate : 4x
Side Band Enabled : Yes
Fast-Writes Enabled : Yes
Aperture Size : 128MB
PCI Bus(es)
Version : 2.20
No Bridges : 2
PCI Bus 0 : 32-bit PCI (1x PCIClk)
PCI Bus 2 : 32-bit PCI (1x PCIClk)
LPC Hub Controller 1
Model : Intel Corporation 82801BA (ICH2) LPC Interface Controller
ACPI PM Enabled : Yes
Random Number Generator Enabled : No
Random Number Generator Support : Yes
USB Controller 1
Model : Intel Corporation 82801BA/BAM (ICH2) USB Universal Host Controller
Version : 1.10
UHCI Interface : Yes
Channels : 2
Speed : 48MHz
Legacy Emulation Enabled : No
USB Controller 2
Model : Intel Corporation 82801BA/BAM (ICH2) USB Universal Host Controller
Version : 1.10
UHCI Interface : Yes
Channels : 2
Speed : 48MHz
Legacy Emulation Enabled : No
System SMBus Controller 1
Model : Intel 801xx SMBus
Version : 0.05
Speed : 16kHz
Expansion Slot(s)
PCI 1 (1h) : PCI 32-bit 5V 3.3V PME HalfLength Available (Intel

Corporation
82845/E/MP/MZ Brookdale CPU to AGP Bridge)
PCI 2 (2h) : PCI 32-bit 5V 3.3V PME HalfLength Available
PCI 3 (3h) : PCI 32-bit 5V 3.3V PME HalfLength Available
PCI 4 (4h) : PCI 32-bit 5V 3.3V PME HalfLength Available
PCI 5 (5h) : PCI 32-bit 5V 3.3V PME HalfLength InUse
PCI 6 (6h) : PCI 32-bit 5V 3.3V PME HalfLength Available
AGP (7h) : AGP-4x 32-bit 3.3V PME HalfLength InUse
Port Connector(s)
PRIMARY IDE/HDD : None - ATA / None
SECONDARY IDE/HDD : None - ATA / None
FLOPPY : None - Floppy / None
USB1 : USB - None / USB
USB2 : USB - None / USB
USB3 : USB - None / USB
USB4 : USB - None / USB
PS/2 Keyboard : Keyboard Port - None / PS/2
PS/2 Mouse : Mouse Port - None / PS/2
Parallel Port : Parallel Port ECP/EPP - None / DB25 pin female
Serial Port 1 : Serial Port 16550 Compatible - None / DB-9 pin male
Serial Port 2 : Serial Port 16550 Compatible - None / DB-9 pin male
Joystick Port : Joystick Port - None / DB-15 pin female
MIDI Port : MIDI Port - None / DB-15 pin female
Line In Jack : Audio Port - None / Mini-jack
Headphone : Audio Port - None / Mini-jack
Microphone : Audio Port - None / Mini-jack
Video Port : Video Port - None / Mini-jack


Found some nv4_ files. Will try to delete all af them and see what
happens...
tomorrow ;-)
Using 53.03 drv

Why can´t I see my AGP/PCI BUS SPEED anymore using fx. sandra, eida and
some more...???



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Is 3.3V aux power standard in PCI 2.2 compatible motherbords? Paul General 2 August 16th 03 02:56 AM


All times are GMT +1. The time now is 11:32 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.