If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Some help with a hd configuration...8KNXP
Man I keep reading the manual and all it does is make me more confused. I
just got a WD raptor HD I'd like to run on my 8KNXP. There's so much conflicting advice out there I thought you masters could straighten me out. This will be my ONLY HD on the system..can I use it to boot? Should I connect it to the ICH5R or the SIL3112? I'd just like to take advantage of a sata drive at this time and maybe move onto a raid configuration later...hence, the single drive. Thanks Don |
#2
|
|||
|
|||
Don,
ICH5R = On Chip SATA controller. ("On Board" is the Silicon image), Manual (not Auto) Config, Sata as Sata. Raid Enabled - even if you have only 1 disc, this is called RAID Ready and enables you to activate RAID at run time when ready after adding another disc of course. The SATA plug goes into the 'top right' SATA connector on the mobo nearest the IDE ports - its not too clear on the v1 mobo. The left SATA's closest to PCI are the SIL SATA ports, the right two are Intel ICH5R. If you are not using the gigaraid (aka ITE) controller, disable it. If you are not using the Silicon Image controller, disable it. Disable all that you do not intend to use immediately. You need the ICH5R raid drivers on floppy for F6 install in Windows XP. If you have Me / 98 you are out of luck & will have to set the controller to replace one of the IDE ports (slower, you lose the corresponding IDE port when a SATA port is mapped like this). For a version 1 board only: Get the latest bios - F10 I think. It will confirm which drive you are booting off more correctly than any other. If you have a bios prior to F6, or the F7, or F8 bios then change to F10. If you are on bios F6 or F9 (both are OK sort of) then it is up to you. F6 does not clearly show you within the bios if you have a SATA disc connected unless you have rebooted a couple of times. Don't know about F9. Personally, I would put the latest bios in (using DOS boot floppy method) and download the SATA drivers afresh to ensure you start with the latest versions. For a version 2 board. Don't know. People didn't seem to have anywhere as much problems with V2's - I would use latest bios and drivers. BOL! HTH - Tim "MTech" wrote in message ... Man I keep reading the manual and all it does is make me more confused. I just got a WD raptor HD I'd like to run on my 8KNXP. There's so much conflicting advice out there I thought you masters could straighten me out. This will be my ONLY HD on the system..can I use it to boot? Should I connect it to the ICH5R or the SIL3112? I'd just like to take advantage of a sata drive at this time and maybe move onto a raid configuration later...hence, the single drive. Thanks Don |
#3
|
|||
|
|||
Thanks a bunch Tim.
I did exactly what you said and all is well:-) Don "Tim" wrote in message ... Don, ICH5R = On Chip SATA controller. ("On Board" is the Silicon image), Manual (not Auto) Config, Sata as Sata. Raid Enabled - even if you have only 1 disc, this is called RAID Ready and enables you to activate RAID at run time when ready after adding another disc of course. The SATA plug goes into the 'top right' SATA connector on the mobo nearest the IDE ports - its not too clear on the v1 mobo. The left SATA's closest to PCI are the SIL SATA ports, the right two are Intel ICH5R. If you are not using the gigaraid (aka ITE) controller, disable it. If you are not using the Silicon Image controller, disable it. Disable all that you do not intend to use immediately. You need the ICH5R raid drivers on floppy for F6 install in Windows XP. If you have Me / 98 you are out of luck & will have to set the controller to replace one of the IDE ports (slower, you lose the corresponding IDE port when a SATA port is mapped like this). For a version 1 board only: Get the latest bios - F10 I think. It will confirm which drive you are booting off more correctly than any other. If you have a bios prior to F6, or the F7, or F8 bios then change to F10. If you are on bios F6 or F9 (both are OK sort of) then it is up to you. F6 does not clearly show you within the bios if you have a SATA disc connected unless you have rebooted a couple of times. Don't know about F9. Personally, I would put the latest bios in (using DOS boot floppy method) and download the SATA drivers afresh to ensure you start with the latest versions. For a version 2 board. Don't know. People didn't seem to have anywhere as much problems with V2's - I would use latest bios and drivers. BOL! HTH - Tim "MTech" wrote in message ... Man I keep reading the manual and all it does is make me more confused. I just got a WD raptor HD I'd like to run on my 8KNXP. There's so much conflicting advice out there I thought you masters could straighten me out. This will be my ONLY HD on the system..can I use it to boot? Should I connect it to the ICH5R or the SIL3112? I'd just like to take advantage of a sata drive at this time and maybe move onto a raid configuration later...hence, the single drive. Thanks Don |
#4
|
|||
|
|||
Look up the ICH5R on Intel.com and download the pdf that gives
instructions for installing the drivers. Follow the 'F6' method. Even though you only have one drive you should install the RAID drivers. If you just map to Primary IDE you will not get the SATA drivers installed. That is what happened to me and now I have get a second drive in order to install the ICH5R driver. The trick is to watch for "to install RAID press F6 now" during boot up, it goes by in a flash. If you proceed to install with out the ICH5R driver you won't get a second chance. THE 'press F6' option does not appear after you have completed installing Windows. That is my situation with A rev 1 board. __________________________________________________ ____________________ Gigabyte 8KNXP, P4 2.8C, Corsair TwinX1024-3200C2PT Cas 2-3-3-5, SiSoft Sandra 2003 Unbuffered ALU 2973MB/s, Int Buff 4909MB/s, Memtest86 2442 MB/s, Zalman CNPS 7000AlCu, WD360GD Raptor, Radeon 8500LL, WinXP Pro MTech wrote: Man I keep reading the manual and all it does is make me more confused. I just got a WD raptor HD I'd like to run on my 8KNXP. There's so much conflicting advice out there I thought you masters could straighten me out. This will be my ONLY HD on the system..can I use it to boot? Should I connect it to the ICH5R or the SIL3112? I'd just like to take advantage of a sata drive at this time and maybe move onto a raid configuration later...hence, the single drive. Thanks Don |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Asus A7N8X-X and AMD Athlon XP 3200+ | Information Scavenger | Asus Motherboards | 30 | November 9th 04 09:30 PM |
P4G8X Dual Channel Memory configuration | Paul | Asus Motherboards | 0 | August 8th 04 08:49 AM |
PCI modem on 8KNXP not working | Dale Foster | Gigabyte Motherboards | 4 | February 1st 04 01:03 PM |
8KNXP slow copying over LAN | Scott | Gigabyte Motherboards | 3 | September 2nd 03 10:54 PM |
8KNXP: where can i find IDE driver? | klausa2 | Gigabyte Motherboards | 3 | August 23rd 03 01:15 AM |