If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
SATA vs eSATA
I'm doing a new build and my case has an eSATA port on the fron panel. The motherboard has a couple of unused SATA ports, but nothing specifically designated as eSATA. Can I connect the front-panel eSATA port to a plain old SATA port on the motherboard, or are these really different things? It looks like the connector will work, but I wonder if there are electrical differences that would make this a bad idea. (I don't really have any plans for using eSATA, so if this can't be done, it's no big deal. But if if would work then I figure I might as well do it.) TIA for any advice. Reply-to address is real -- John |
#2
|
|||
|
|||
SATA vs eSATA
In the last episode of ,
John said: I'm doing a new build and my case has an eSATA port on the fron panel. The motherboard has a couple of unused SATA ports, but nothing specifically designated as eSATA. Can I connect the front-panel eSATA port to a plain old SATA port on the motherboard, or are these really different things? It looks like the connector will work, but I wonder if there are electrical differences that would make this a bad idea. (I don't really have any plans for using eSATA, so if this can't be done, it's no big deal. But if if would work then I figure I might as well do it.) TIA for any advice. As a rule, you can connect eSATA ports on your case to onboard SATA ports. They're electrically compatible, the problem is with poorly written drivers that fail to cope with hotswap situations. This can be an issue with native eSATA ports too, not just converted ports. -- The nice thing about standards, there is enough for everyone to have their own. |
#3
|
|||
|
|||
SATA vs eSATA
On Tue, 12 Feb 2013 09:49:06 -0500, John
wrote: I'm doing a new build and my case has an eSATA port on the fron panel. The motherboard has a couple of unused SATA ports, but nothing specifically designated as eSATA. Can I connect the front-panel eSATA port to a plain old SATA port on the motherboard, or are these really different things? It looks like the connector will work, but I wonder if there are electrical differences that would make this a bad idea. (I don't really have any plans for using eSATA, so if this can't be done, it's no big deal. But if if would work then I figure I might as well do it.) There are some external drives, Seagate Free Agent GoFlex Ultra-Portable, for instance that require +5 on what is normally the data only cable for operation. There might be some that need both +5 and +12. Therefore you should check for eSATAp (eSATA with power) and/or USB/eSATA combination ports. The eSATAp ports come in both +5 and (+5,+12V) versions. Maximum current at each voltage should also be considered. TIA for any advice. Reply-to address is real -- John |
#4
|
|||
|
|||
SATA vs eSATA
John wrote:
I'm doing a new build and my case has an eSATA port on the fron panel. The motherboard has a couple of unused SATA ports, but nothing specifically designated as eSATA. Can I connect the front-panel eSATA port to a plain old SATA port on the motherboard, or are these really different things? It looks like the connector will work, but I wonder if there are electrical differences that would make this a bad idea. (I don't really have any plans for using eSATA, so if this can't be done, it's no big deal. But if if would work then I figure I might as well do it.) TIA for any advice. Reply-to address is real -- John SATA and ESATA are identical on protocol. There is a slight difference in the electrical (analog) specs. ESATA has a bit more budget on the difference between transmit level and min usable receive level. And that allows a slightly longer cable to be used. http://en.wikipedia.org/wiki/Sata#eSATA Minimum transmit amplitude increased: Range is 500–600 mV instead of 400–600 mV. --- launch amplitude Minimum receive amplitude needed: Range is 240–600 mV instead of 325–600 mV. --- receive sensitivity Maximum cable length increased to 2 meters (from 1 meter) The first two items there, is what allows the cable to be longer. Some chipsets claim to support both SATA and ESATA, but I've never seen any detail as to whether something has to be programmed to make it work. It would seem they just run in ESATA mode all the time, ready to work with a longer cable if one comes along. Because I can't see any info to suggest a register needs to be flipped to do one or the other. If you have some ESATA setup of questionable heritage, you can try using a shorter cable than the max stated by the ESATA spec, as a crutch. If you think you're getting transmission errors on the cable, the shorter cable may help a tiny bit. Paul |
#5
|
|||
|
|||
SATA vs eSAT
On Tue, 12 Feb 2013 09:49:06 -0500, John
wrote: I'm doing a new build and my case has an eSATA port on the fron panel. The motherboard has a couple of unused SATA ports, but nothing specifically designated as eSATA. Can I connect the front-panel eSATA port to a plain old SATA port on the motherboard, or are these really different things? It looks like the connector will work, but I wonder if there are electrical differences that would make this a bad idea. (I don't really have any plans for using eSATA, so if this can't be done, it's no big deal. But if if would work then I figure I might as well do it.) TIA for any advice. Reply-to address is real -- John Thanks all for the help. Since I have no eSATA devices at the moment, I buttoned up the case with the front-panel eSATA cable not connected. But it sounds like I can hook it up if I need it and it'll probably work. I'll keep that in mind. Reply-to address is real John |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Very slow SATA and eSata peformance | Smarty | Storage (alternative) | 40 | September 3rd 09 06:10 PM |
Which do you think will be around longer - SATA, eSATA or USB? | JLH | Homebuilt PC's | 7 | May 30th 08 01:18 AM |
eSATA (external SATA) | Timothy Daniels | Storage (alternative) | 19 | March 20th 07 12:59 AM |
eSATA (external SATA) | Timothy Daniels | Dell Computers | 0 | March 14th 07 05:17 PM |
eSATA (external SATA) | Timothy Daniels | Homebuilt PC's | 0 | March 14th 07 05:17 PM |