If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
power problems
I have just installed a kx600 motherboard with an athlon 1ghz cpu and have
encountered a problem I hope you can help me resolve. When I first started the system after installing the new motherboard everything started okay but when I cut the power with the power switch the system would not start again. I had a look inside while I was pressing the power switch in and noticed the fans were turning a little bit . I then tried pulling the power cables from the CD player and hard drive and floppy. Then after trying the power switch again the system started. There is no set pattern to what power cables I pull out to allow the system to start - I just keep on pulling cables out and eventually the system starts. Once it is running the system will stay running and restart with the restart switch but as soon as I kill the power it won't start again. A couple of times after the system has been running I have inserted a CD and the power has shut down instantaneously. I have tried swapping the restart switch and the power switch around but still have the same problem . My power supply is a MEC model ATX 350/2F and is only a couple of weeks old. Any advice you can give would be greatly appreciated. Regards gregork |
#2
|
|||
|
|||
gregork wrote: I have just installed a kx600 motherboard with an athlon 1ghz cpu and have encountered a problem I hope you can help me resolve. When I first started the system after installing the new motherboard everything started okay but when I cut the power with the power switch the system would not start again. I had a look inside while I was pressing the power switch in and noticed the fans were turning a little bit . I then tried pulling the power cables from the CD player and hard drive and floppy. Then after trying the power switch again the system started. There is no set pattern to what power cables I pull out to allow the system to start - I just keep on pulling cables out and eventually the system starts. Once it is running the system will stay running and restart with the restart switch but as soon as I kill the power it won't start again. A couple of times after the system has been running I have inserted a CD and the power has shut down instantaneously. I have tried swapping the restart switch and the power switch around but still have the same problem . My power supply is a MEC model ATX 350/2F and is only a couple of weeks old. Any advice you can give would be greatly appreciated. Regards gregork Your description has all the earmarks of a power supply that is being overloaded. I realize that your PS is only a couple of weeks old, but that is what I would try first. |
#3
|
|||
|
|||
I had this problem when I installed a new motherboard about a year ago, but can't remember what caused it. It could have something to do with power management. It was not bad hardware. gregork wrote: I have just installed a kx600 motherboard with an athlon 1ghz cpu and have encountered a problem I hope you can help me resolve. When I first started the system after installing the new motherboard everything started okay but when I cut the power with the power switch the system would not start again. I had a look inside while I was pressing the power switch in and noticed the fans were turning a little bit . -- Mike Walsh West Palm Beach, Florida, U.S.A. |
#4
|
|||
|
|||
It sounds like you have a cheap power supply that is unable to supply
adequate wattage to drive the components you have. I would highly consider investing in a "quality" brand power supply of adequate wattage. (Just because a given power supply is rated to put out 350 Watts does NOT mean that it actually can in the real world. That's why people invest in more expensive power supplies. They really can supply a constant 350 Watts. Antec is a very good brand.) -- DaveW "gregork" wrote in message ... I have just installed a kx600 motherboard with an athlon 1ghz cpu and have encountered a problem I hope you can help me resolve. When I first started the system after installing the new motherboard everything started okay but when I cut the power with the power switch the system would not start again. I had a look inside while I was pressing the power switch in and noticed the fans were turning a little bit . I then tried pulling the power cables from the CD player and hard drive and floppy. Then after trying the power switch again the system started. There is no set pattern to what power cables I pull out to allow the system to start - I just keep on pulling cables out and eventually the system starts. Once it is running the system will stay running and restart with the restart switch but as soon as I kill the power it won't start again. A couple of times after the system has been running I have inserted a CD and the power has shut down instantaneously. I have tried swapping the restart switch and the power switch around but still have the same problem . My power supply is a MEC model ATX 350/2F and is only a couple of weeks old. Any advice you can give would be greatly appreciated. Regards gregork |
#5
|
|||
|
|||
On Sun, 28 Dec 2003 21:36:24 GMT In this world we created "DaveW"
wrote : It sounds like you have a cheap power supply that is unable to supply adequate wattage to drive the components you have. I would highly consider investing in a "quality" brand power supply of adequate wattage. Wattage is not the issue :/ -- Free Windows/PC help, http://www.geocities.com/sheppola/trouble.html email shepATpartyheld.de Free songs download, http://www.soundclick.com/bands/8/nomessiahsmusic.htm |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Power on Problems | Gemjack | General | 2 | November 1st 03 02:09 PM |
Silent Computer - Advice | David Taylor | General | 49 | October 7th 03 11:26 AM |
Power Problems | TresWBL | General | 1 | September 27th 03 03:22 PM |
How can I make motherboard to restart after power loss automatically? | Amiran | General | 1 | September 24th 03 11:35 PM |
Power problems on Dell thing | Zilog Jones | General | 8 | July 23rd 03 06:16 PM |