If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
"New" C2 Duo's?
Guys
I asume the new (1300?FSB) chips aren't good for us OC'ers? thx bob |
#2
|
|||
|
|||
"New" C2 Duo's?
'Billy Bob' wrote:
| I asume the new (1300?FSB) chips aren't good for us OC'ers? _____ Maybe yes, maybe no. Depends on how high an FSB the motherboard can use and, as always, the individual CPU chip. Motherboards based on the nVidia 680i have been shown to work well with an FSB of 1600 MHz. For a 2.66 GHz Core 2 Duo 1333 MHz FSB CPU a 1600 MHz FSB would give a 3.2 GHz overclock. As for me, I picked an 800 MHz FSB Core 2 Duo as a start in March, and would consider upgrading to a 45 nm CPU but not to a 1333 MHz FSB 65 nm CPU. Phil Weldon "Billy Bob" wrote in message . .. | Guys | | I asume the new (1300?FSB) chips aren't good for us OC'ers? | | | thx | | bob | | |
#3
|
|||
|
|||
"New" C2 Duo's?
Phil Weldon wrote:
'Billy Bob' wrote: | I asume the new (1300?FSB) chips aren't good for us OC'ers? _____ Maybe yes, maybe no. Depends on how high an FSB the motherboard can use and, as always, the individual CPU chip. Motherboards based on the nVidia 680i have been shown to work well with an FSB of 1600 MHz. For a 2.66 GHz Core 2 Duo 1333 MHz FSB CPU a 1600 MHz FSB would give a 3.2 GHz overclock. Sounds like NB cooling is going to become an issue for some. My MSI gets unable-to-touch hot with my NB running at 315MHz. For the die-hards, it'll give a small degree of better adjustability. As for me, I picked an 800 MHz FSB Core 2 Duo as a start in March, and would consider upgrading to a 45 nm CPU but not to a 1333 MHz FSB 65 nm CPU. Good point. I may give it a go. -- Phil |
#4
|
|||
|
|||
"New" C2 Duo's?
The nVidia 680i motherboard reference design has a moderately large (40 mm X
50 mm X 30 mm fin pack) heatsink and 50 mm 5000 rpm fan on the Nortbridge, connected by a heatpipe to a heatsink on the Southbridge. The ThermalTake i1 (~ $30 US) arrangement is a nice fit in that its airflow does not interact with the airflow of the fin pack/fan on the nVidia 680i reference design Northbridge heatsink/fan. The ThermalTake i1 airflow is parallel to the surface of the motherboard, directed from the internal connecter (front) side of the motherboard toward the external connector (rear) side of the motherboard. The Northbridge air flow is parallel to the motherboard directed from the CPU end of the motherboard twoard the adapter slot end. The ThermalTake i1 fin pack is almost entirely further from the motherboard than the Northbridge fin pack. I think this is probably the best possible arrangement for air cooling when using a Core 2 CPU with a high speed FSB. With my E4300 / EVGA 680i I've had no trouble using a 1333 MHz FSB (multiplier X8) with the above air cooling arrangement. Had I the chance to do it over, I might chose the ASUS 680i motherboard over the EVGA motherboard but only because of the possibility that the ASUS temperature/fan speed/voltage monitor program might give more results than nVidia nTune and NVMonitor. (I originally passed over the ASUS because I could not download the motherboard manual from the ASUS web site - but since that time (March) I have been able to download that manual.) Phil Weldon "Phil" wrote in message ... | Phil Weldon wrote: | 'Billy Bob' wrote: | | I asume the new (1300?FSB) chips aren't good for us OC'ers? | _____ | | Maybe yes, maybe no. Depends on how high an FSB the motherboard can | use and, as always, the individual CPU chip. Motherboards based on | the nVidia 680i have been shown to work well with an FSB of 1600 MHz. | For a 2.66 GHz Core 2 Duo 1333 MHz FSB CPU a 1600 MHz FSB would give | a 3.2 GHz overclock. | | Sounds like NB cooling is going to become an issue for some. My MSI gets | unable-to-touch hot with my NB running at 315MHz. For the die-hards, it'll | give a small degree of better adjustability. | | As for me, I picked an 800 MHz FSB Core 2 Duo as a start in March, | and would consider upgrading to a 45 nm CPU but not to a 1333 MHz FSB | 65 nm CPU. | | Good point. I may give it a go. | -- | Phil | | |
#5
|
|||
|
|||
"New" C2 Duo's?
Phil Weldon wrote:
The nVidia 680i motherboard reference design has a moderately large (40 mm X 50 mm X 30 mm fin pack) heatsink and 50 mm 5000 rpm fan on the Nortbridge, connected by a heatpipe to a heatsink on the Southbridge. The ThermalTake i1 (~ $30 US) arrangement is a nice fit in that its airflow does not interact with the airflow of the fin pack/fan on the nVidia 680i reference design Northbridge heatsink/fan. The ThermalTake i1 airflow is parallel to the surface of the motherboard, directed from the internal connecter (front) side of the motherboard toward the external connector (rear) side of the motherboard. The Northbridge air flow is parallel to the motherboard directed from the CPU end of the motherboard twoard the adapter slot end. The ThermalTake i1 fin pack is almost entirely further from the motherboard than the Northbridge fin pack. I think this is probably the best possible arrangement for air cooling when using a Core 2 CPU with a high speed FSB. With my E4300 / EVGA 680i I've had no trouble using a 1333 MHz FSB (multiplier X8) with the above air cooling arrangement. Had I the chance to do it over, I might chose the ASUS 680i motherboard over the EVGA motherboard but only because of the possibility that the ASUS temperature/fan speed/voltage monitor program might give more results than nVidia nTune and NVMonitor. (I originally passed over the ASUS because I could not download the motherboard manual from the ASUS web site - but since that time (March) I have been able to download that manual.) Phil Weldon "Phil" wrote in message ... | Phil Weldon wrote: | 'Billy Bob' wrote: | | I asume the new (1300?FSB) chips aren't good for us OC'ers? | _____ | | Maybe yes, maybe no. Depends on how high an FSB the motherboard | can use and, as always, the individual CPU chip. Motherboards | based on the nVidia 680i have been shown to work well with an FSB | of 1600 MHz. For a 2.66 GHz Core 2 Duo 1333 MHz FSB CPU a 1600 | MHz FSB would give a 3.2 GHz overclock. | | Sounds like NB cooling is going to become an issue for some. My | MSI gets unable-to-touch hot with my NB running at 315MHz. For the | die-hards, it'll | give a small degree of better adjustability. | | As for me, I picked an 800 MHz FSB Core 2 Duo as a start in March, | and would consider upgrading to a 45 nm CPU but not to a 1333 MHz | FSB 65 nm CPU. | | Good point. I may give it a go. | -- | Phil My MSI is a nVidia 650 mobo with a super-thin HS. I don't really know if my NB cooling is a problem... yet. I may swap out my E4300 with a 6750 if it turns out well. -- Phil |
#6
|
|||
|
|||
"New" C2 Duo's?
NB Cooling?
bob "Phil" wrote in message ... Phil Weldon wrote: 'Billy Bob' wrote: | I asume the new (1300?FSB) chips aren't good for us OC'ers? _____ Maybe yes, maybe no. Depends on how high an FSB the motherboard can use and, as always, the individual CPU chip. Motherboards based on the nVidia 680i have been shown to work well with an FSB of 1600 MHz. For a 2.66 GHz Core 2 Duo 1333 MHz FSB CPU a 1600 MHz FSB would give a 3.2 GHz overclock. Sounds like NB cooling is going to become an issue for some. My MSI gets unable-to-touch hot with my NB running at 315MHz. For the die-hards, it'll give a small degree of better adjustability. As for me, I picked an 800 MHz FSB Core 2 Duo as a start in March, and would consider upgrading to a 45 nm CPU but not to a 1333 MHz FSB 65 nm CPU. Good point. I may give it a go. -- Phil |
#7
|
|||
|
|||
"New" C2 Duo's?
"Billy Bob" wrote in message ... NB Cooling? bob Northbridge chipset cooling. The 680i chipset is known for quite a bit of heat at the northbridge. Ed |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Which Printer Is Pick Of The Crop "The Best" In Your Opinion My"Shortlist" | Heidy | Printers | 8 | March 17th 07 09:07 PM |
Force "medium present" or "device ready"? | Mike Richter | Cdr | 5 | October 23rd 06 12:12 AM |
Downside of changing "Max frames to render ahead"/"Prerender Limit" to 1/0? | Jeremy Reaban | Nvidia Videocards | 2 | March 31st 06 04:24 AM |
ASUS A8V & ATI AIW 9600 "inf" "thunk.exe" error message? | ByTor | AMD x86-64 Processors | 5 | January 13th 06 06:50 PM |