If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
K8N-E Question about Powerfan Threshold
Using PC Probe tells me that the Powerfan is below threshold. Obviously
because there is nothing connected to it. All fans seem to be spinning. Just confirming that I should just uncheck this setting for monitoring? Also, what is the connector for? Just an extra fan? I actually thought it was getting that reading because I might have negelected to to put the cable coming from the power supply to the PWR_FAN connector. (currently on the chassis connector and works fine. I get a CPU error when it's connected to the power fan connector) Many thanks in advance. |
#2
|
|||
|
|||
Thanks for the reply.
Got another question. Receiving an error sometimes when booting "CPU Fan Error, Press F1 to Continue". All fans are confirmed working. CPU temperature when booting to BIOS upon boot is about 42C/107F and climbing rapidly. When booting into Windows, temperature reduces to about a steady 38C/100F. Cool n' quiet is disabled. Thanks in advance for any help. "Ed" wrote in message ... On Sat, 18 Dec 2004 22:21:10 -0500, "Christopher Bogart" wrote: Using PC Probe tells me that the Powerfan is below threshold. Obviously because there is nothing connected to it. All fans seem to be spinning. Just confirming that I should just uncheck this setting for monitoring? If there is no fan connected to the fan header then there is nothing to monitor so uncheck monitoring in pc probe. Also, what is the connector for? Just an extra fan? yep, most asus boards have at least 3 fan headers with monitoring, usually named CPU, Chassis and Power. I actually thought it was getting that reading because I might have negelected to to put the cable coming from the power supply to the PWR_FAN connector. (currently on the chassis connector and works fine. I get a CPU error when it's connected to the power fan connector) That's weird. My PSU has a wire for the fan also, but it's only for monitoring the PSU fan speed, not powering it. Many thanks in advance. Cheers, Ed -- PCpTray - Add-on utility for Asus PC Probe http://tinyurl.com/6bhxe |
#3
|
|||
|
|||
Receiving an error sometimes when booting "CPU Fan Error, Press F1 to
Continue". All fans are confirmed working. CPU temperature when booting to BIOS upon boot is about 42C/107F and climbing rapidly. When booting into Windows, temperature reduces to about a steady 38C/100F. Cool n' quiet is disabled. Thanks in advance for any help. Do you have Q-Fan enabled? This will throttle fan speeds according to CPU temperature in order to quiet down the system. (It operates independently from Cool'n'Quiet.) In my experience, it doesn't work well, so I just turned it off. This particular problem seems to be caused by the fact that when the system is powered up cold, the CPU hasn't warmed up enough to require the fan to come on when the POST checks CPU fan speed. So it complains about a fan failure. |
#4
|
|||
|
|||
I'm not positive which one I have enabled right now (Q-Fan or Cool n'
Quiet), but playing with enabling/disabling each, tells me that either both have to be turned off or only one can be on (I think it's Cool n' Quiet. I think the Q-Fan stopped the CPU fan). Turns my 2nd problem with the CPU fan not spinning upon bootup was a BIOS problem. I had updated to the lastest bios 1006 and for whatever reason the CPU fan would not spin. I installed the first BIOS version, then upgraded to 1005 and it seems to work well. Temperature seems quite cool now. Thanks for everyone's help. "Lachoneus" wrote in message ... Receiving an error sometimes when booting "CPU Fan Error, Press F1 to Continue". All fans are confirmed working. CPU temperature when booting to BIOS upon boot is about 42C/107F and climbing rapidly. When booting into Windows, temperature reduces to about a steady 38C/100F. Cool n' quiet is disabled. Thanks in advance for any help. Do you have Q-Fan enabled? This will throttle fan speeds according to CPU temperature in order to quiet down the system. (It operates independently from Cool'n'Quiet.) In my experience, it doesn't work well, so I just turned it off. This particular problem seems to be caused by the fact that when the system is powered up cold, the CPU hasn't warmed up enough to require the fan to come on when the POST checks CPU fan speed. So it complains about a fan failure. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Heatsink Question | Paul | Asus Motherboards | 0 | August 31st 04 11:27 AM |
Pentium question | Robert Sligh | Overclocking AMD Processors | 4 | April 27th 04 01:13 PM |
Real Abit Question | Jim | Abit Motherboards | 0 | April 3rd 04 09:48 PM |
Memory Question - outcome of exceeding the memory limits of a machine. | John B. | General | 4 | November 4th 03 12:25 PM |
Follow-up question | James Silkworth | Asus Motherboards | 2 | July 27th 03 05:42 PM |