If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
ABIT VP6 "ERROR LOADING OPERATING SYSTEM" revised
Dear Sirs/Madam:
I have a Abit VP6 dual proc. I have a delima of an: "ERROR LOADING OPERATING SYSTEM". The main HD is a IBM Deskstar IDE/ ATA 100 80GB. I could not get my main HD to boot up no matter what I did including a low format or a fill using my own Win2Kpro disk. I pulled it out and got one of my friends to format it for me on his computer system using WinXPpro. We did a disk check on the HD, there were no bad blocks and the HD was still good. When that was done I brought it back to my system and my Win2Kpro disk booted up the HD. I wasen't shure if it would boot rite so I deleted the partition and reformated it agian using the boot up disk of Win2Kpro. My HD is NTSF formated. After the full clean install I rebooted and went into my CMOS and changed the boot set up to 1st: HD-0/ 2nd: CD-ROM/ 3rd: FLOPPY and manually filled the CHS of my HD-0. As soon as I restarted it agian it went through it's process of boot up. Afterwards it said "VERIFYING DMI POOL DATA", then said "ERROR LOADING OPERATING SYSTEM". This is what my setup looks like when it goes through a Verifying DMI Pool Data: CPU ID/ucode ID: 0686/08 CPU Clock: 1000B Mhz Extended Memory: 2096128K Cache Memory: 256K/ 256K Diskette Drive A: 1.44M, 3.5in. Diskette Drive B: none Pri Master: CHS,ATA 100, 76GB Pri Slave: none Sec. Master: DVD-RW,ATA 33 Sec. Slave: none Display Type: EGA/VGA Serial Ports: 3F8 2F8 Parallel Ports: 378 SDRAM at DIMM: 0 1 2 3 manual mode: 16383 CYL 16 HDS 63 SEC Boot up formation: HD-0 CD-ROM FLOPPY I am so despritely trying to just load up the OS in this system. Then later install all the stuff on it. This workstation is loaded to it's gills in memory and storage space for the renders that I produce on Maya. My HD system consist of: (1) IMB Deskstar ATA/100 80GB HD C: drive (1) IMB Deskstar ATA/100 80GB HD D: drive Highpoint 370 RAID-0 (4) Seagate Barracuda ATA/IV 100 80GB HD = 320GB Dual Hot Swap using USB 2.0 (2) Seagate Barracuda UATA/100 200GB HD = 400GB Floopy ZIP100 Pioneer DVD-RW/ CD-RW combo drive This system is mostly used for Alias|Wavefront Maya, After Effects and Premiere the dual proc is excellent for rendering. I am only a student on a student budget so when I went to a PC repair shop they seem to want to charge me up the WAH-ZOO when they look at my system. Hope you can help me, need help badly please. You can email me back at: Thank you, ROM |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Multi-boot Windows XP without special software | Timothy Daniels | General | 11 | December 12th 03 05:38 AM |
PII vs PIII | Gregory L. Hansen | General | 114 | October 15th 03 05:56 PM |
ABIT VP6 "ERROR LOADING OPERATIN SYSTEM" revised | SiLapuLapu | Homebuilt PC's | 0 | October 14th 03 10:57 PM |
ABIT VP6 "ERROR LOADING OPERATING SYSTEM" | SiLapuLapu | Homebuilt PC's | 1 | October 14th 03 03:11 PM |
Cooling Questions | Peter Cavan | General | 35 | September 2nd 03 06:42 AM |