Getting an x1950 AGP running on a KT400-based mobo

I'm struggling and currently failing to get an x1950Pro running on a Via
KT400-based motherboard (an A7V8X). This is under WinXP SP3.

The combination runs an x800 XT PE fine with the Cat 7.2 drivers - but
although it will install any ATI driver seemingly OK, I end up with
either no D3D acceleration, no AGP capability, crashes in the SMARTGART
testing on re-boot, missing desktop icons or display stuck at
640x480x4-bit, or any combination of the above.

I've tried the latest 9.11 "legacy" drivers, Cat 7.2, Cat 7.12 and Omega
drivers based upon Cat 7.12.

:-(

Any suggestions of BIOS settings, driver version etc. to try to attempt
to get this combination running? I'm assured the card is a good'un, but
have no other machine to test it it.

PSU is an Enermax 400W, which runs the X800 XT PE fine, and that and the
1950Pro have very similar power requirements.

Thanks for any help.

Ian
--
Ian Riches
Bedford, UK

In article , Ian Riches wrote:
I'm struggling and currently failing to get an x1950Pro running on a Via
KT400-based motherboard (an A7V8X). This is under WinXP SP3.

The combination runs an x800 XT PE fine with the Cat 7.2 drivers - but
although it will install any ATI driver seemingly OK, I end up with
either no D3D acceleration, no AGP capability, crashes in the SMARTGART
testing on re-boot, missing desktop icons or display stuck at
640x480x4-bit, or any combination of the above.

I've tried the latest 9.11 "legacy" drivers, Cat 7.2, Cat 7.12 and Omega
drivers based upon Cat 7.12.

:-(

Any suggestions of BIOS settings, driver version etc. to try to attempt
to get this combination running? I'm assured the card is a good'un, but
have no other machine to test it it.

PSU is an Enermax 400W, which runs the X800 XT PE fine, and that and the
1950Pro have very similar power requirements.

Thanks for any help.

Ian




You really should install this, then reinstall the drivers for your video
card. The Hyperion drivers have drivers that support the KT400 chipset and are
needed for proper AGP functioning.


http://www.viaarena.com/Driver/VIA_H...nPro_V524A.zip






OS Supported:
Windows Server 2003 x64, Windows Vista 32-Bit, Windows Vista 64-Bit, Windows
ME, Windows XP, Windows XP 64-Bit, Windows 98SE, Windows 98, Windows 2000,
Windows NT


Notes:
Version 5.24A of the Hyperion Pro drivers includes the following components:
INF V3.10A, AGP V4.60A, V-RAID V5.80F and RAID Tools v5.85, VIA IDE Falcon
Storage Device driver v2.80A.

VIA Hyperion Pro drivers are suitable for ANY VIA chipset - but they are
particularly recommended for KT4## series, P4X4## series and newer, for

example:
K7 chipsets: KT400, KT400A, KT600, KT880, KM400, KN400
K8 chipsets: K8T800, K8T800Pro, K8M800, K8M890, K8N800, K8N890, K8T890,
K8T890Pro, K8T900
P4 chipsets: P4X400, P4X400A, PT800, PT880, PM800, PN800, PM880, PN880,
PT880Pro, PT894, P4M800/Pro/CE, P4M900, PT890
C Series Chipsets: CN700, CN400, CLE266, CX700,CX700M, CX700M2, CN800, CN896
V Series Chipsets: VN800, VN896, VX700, VX800, VX800UT, VX820, VX820UT, VX855

On 21/12/2009 17:41, GMAN wrote:
In , Ian wrote:
I'm struggling and currently failing to get an x1950Pro running on a Via
KT400-based motherboard (an A7V8X). This is under WinXP SP3.

tale of woe snipped

You really should install this, then reinstall the drivers for your video
card. The Hyperion drivers have drivers that support the KT400 chipset and are
needed for proper AGP functioning.

http://www.viaarena.com/Driver/VIA_H...nPro_V524A.zip

Sorry...should have said, latest Hyperion drivers have been installed.

Tried again last night with no success. Tried to bypass SMARTGART by
installing the drivers via the directly from Windows rather than by
running the ATI .ese file. Got endless "Monitor signal out of range"
messages displayed on my TFT. Oh well.

Ian
--
Ian Riches
Bedford, UK