If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Why mechanical failure causes HDD being undetectable by bios or OS ?
Hi!
Could someone please explain why in the case of *mechanical* failure HD becomes sometimes undetected by BIOS and/or the operating system (e.g. win xp or linux)? If it was an electronic failure then such behaviour would be obious, but why the same happens with some mechanical failures? When electronics is working in my opinion it still should be detected by bios and/or the system (win xp or linux), but often it is not. I could recover about 80% of the data from my HDD (which apparently has a mechanical failure - plates spin up and down, heads create bad noises) if only the disk could be seen by the system all the time. But often during copying of the data heads hit with a loud sound so badly that sometimes even the plates stop rotating, and the disk then dissapears from the system. It is then very difficult to make it detectable by the system again, sometimes the sytem can detect it but only after several minutes of copying it freezes and then dissapears again. Recently, I was unlucky, and even after several dozens of retries it's still undetectable by the system. Could you please advice what to do to make the disk detectable by the system all the time? What causes that it is not detectable although the failure is in mechanics not electronics? BTW, if someone has the same disk model (Quantum Fireball ST64A011), please let me know. andy |
#2
|
|||
|
|||
"andy" wrote in message ... Hi! Could someone please explain why in the case of *mechanical* failure HD becomes sometimes undetected by BIOS and/or the operating system (e.g. win xp or linux)? Consider the options available to the HD designer. What do you want the user to see during POST about a HD that knows itself that it can't possibly work. The HD designer knows that many BIOSs have no ability to detect and display a HD error status during POST. The BIOS may only be able to report 'there' or 'not there'. If you were the HD designer would you want the HD to report 'there' during POST even when the HD itself really knew that it wasn't there? How would you answer the query of a poster in this NG who wanted to know why a HD reported 'there' during post but was not there for all intents and purposes for any booting steps after POST? Did the HD designer make the correct design choice in the first place which would likely cause a competent user to try another HD and assume that the HD was dead dead which in fact it is? If it was an electronic failure then such behaviour would be obious, but why the same happens with some mechanical failures? When electronics is working in my opinion it still should be detected by bios and/or the system (win xp or linux), but often it is not. What on earth for? Such would be highly misleading and a very poor design choice. I could recover about 80% of the data from my HDD (which apparently has a mechanical failure - plates spin up and down, heads create bad noises) if only the disk could be seen by the system all the time. Huh? But often during copying of the data heads hit with a loud sound so badly that sometimes even the plates stop rotating, and the disk then dissapears from the system. Duh! It is then very difficult to make it detectable by the system again, sometimes the sytem can detect it but only after several minutes of copying it freezes and then dissapears again. Recently, I was unlucky, and even after several dozens of retries it's still undetectable by the system. Could you please advice what to do to make the disk detectable by the system all the time? What causes that it is not detectable although the failure is in mechanics not electronics? The drive is DOA! BTW, if someone has the same disk model (Quantum Fireball ST64A011), please let me know. |
#3
|
|||
|
|||
Thanks for your reply. If it was an electronic failure then such behaviour would be obious, but why the same happens with some mechanical failures? When electronics is working in my opinion it still should be detected by bios and/or the system (win xp or linux), but often it is not. What on earth for? Such would be highly misleading and a very poor design choice. But I could then recover 80% of my data, and now I can recover 0% of my data. Does it make sense for you now? Is there any way to disable that feature? (I mean to make the malfunctioned HDD visible to the system again?) The drive is DOA! Don't get DOA. a. |
#4
|
|||
|
|||
"andy" wrote in message
... Hi! Could someone please explain why in the case of *mechanical* failure HD becomes sometimes undetected by BIOS and/or the operating system (e.g. win xp or linux)? *Sometimes* ... So, maybe it's the nature of the problem that prevents the disk from being detected. If it was an electronic failure then such behaviour would be obious, but why the same happens with some mechanical failures? When electronics is working in my opinion It is hardly a matter of opinion ... it still should be detected by bios and/or the system (win xp or linux), but often it is not. I could recover about 80% of the data from my HDD How do you know? How did you come up with the 80%? (which apparently has a mechanical failure - plates spin up and down, heads create bad noises) if only the disk could be seen by the system all the time. But often during copying of the data heads hit with a loud sound so badly that sometimes even the plates stop rotating, and the disk then dissapears from the system. It is then very difficult to make it detectable by the system again, sometimes the sytem can detect it but only after several minutes of copying it freezes and then dissapears again. You should try to clone it as long as you can see it. However, every read may worsen the condition of the disk, in general it is advised to cease DIY recovery attempts (if the data is important to you) when a disk is maing unusual and scary noises. Recently, I was unlucky, and even after several dozens of retries it's still undetectable by the system. Could you please advice what to do to make the disk detectable by the system all the time? Your issue is a psychological one. You can not accept that there are situations you can not resolve and have no control over. Apart from contacting a data recovery lab, you also need to work out this problem. BTW, if someone has the same disk model (Quantum Fireball ST64A011), please let me know. Why do you want to know? -- Joep |
#5
|
|||
|
|||
On Fri, 3 Sep 2004 11:24:48 +0200, "Joep" j o e p @ d i y d a t a r e c o v e
r y . n l wrote: "andy" wrote in message .. . *Sometimes* ... So, maybe it's the nature of the problem that prevents the disk from being detected. Failure to mechanics seems to be the problem causing the non-detection problem. Unfortunatelly the "sometimes" is now "nearly always". How do you know? How did you come up with the 80%? When the disk was detectable then about 20% of files could not be read. This was not because bad sectors (the disk did not have any AFAIK), but because of the mechanics failure (when it started to have the symptoms of the failure also 20% of data became unavailable). You should try to clone it as long as you can see it. However, every read may worsen the condition of the disk, in general it is advised to cease DIY recovery attempts (if the data is important to you) when a disk is maing unusual and scary noises. Yes, it seems that the condition very quickly became much worse. Your issue is a psychological one. You can not accept that there are situations you can not resolve and have no control over. Apart from How can I know that? If they designed it that way that it should not be detectable when mechanics fails, then maybe also for the service purpose they designed it also to be possible to disable that feature, making the disk visible despite mechanical failure. I hoped that someone knows how to disable that feature. Why do you want to know? If someone has such disk with bad electronics, but good mechanics, then I could use the mechanics to recover my data. Just for one time recovery even opening the disk in not sufficiently clean condition possibly could work. a. |
#6
|
|||
|
|||
andy wrote:
Hi! Could someone please explain why in the case of *mechanical* failure HD becomes sometimes undetected by BIOS and/or the operating system (e.g. win xp or linux)? If it was an electronic failure then such behaviour would be obious, but why the same happens with some mechanical failures? When electronics is working in my opinion it still should be detected by bios and/or the system (win xp or linux), but often it is not. I could recover about 80% of the data from my HDD (which apparently has a mechanical failure - plates spin up and down, heads create bad noises) if only the disk could be seen by the system all the time. But often during copying of the data heads hit with a loud sound so badly that sometimes even the plates stop rotating, and the disk then dissapears from the system. It is then very difficult to make it detectable by the system again, sometimes the sytem can detect it but only after several minutes of copying it freezes and then dissapears again. Recently, I was unlucky, and even after several dozens of retries it's still undetectable by the system. Could you please advice what to do to make the disk detectable by the system all the time? What causes that it is not detectable although the failure is in mechanics not electronics? BTW, if someone has the same disk model (Quantum Fireball ST64A011), please let me know. andy Maybe it stores part of its own software on the platters. -- The e-mail address in our reply-to line is reversed in an attempt to minimize spam. Our true address is of the form . |
#7
|
|||
|
|||
It's not a "feature". The mechanical noises and other symptoms you describe most likely result from a head crash, where the heads, which normally float on a very thin cushion of air, have contacted the disk surface and scraped the oxide off the disk, making it unreadable. If it can't be read, it won't come "ready" (as in "ready to use") and the BIOS won't detect it. Once the heads It doesn't make sense to me. Even if part of the surface is destroyed, most of it is not, why then not to detect the disk? crash, it only gets worse. If you open it up, you'll probably find bare spots on the disks where your data once was. I opened it now (I don't care about the dust, since it's dead anyway), and the surface of the first plate is in perfect condition, I can't see surfaces of other plates, though. To repeat, it's not a "feature" that can be disabled. Your drive is dead. Trust me, I've serviced computer disk drives of various kinds since long before PC's existed, and I know how they fail. I know it's broken down, but still, this behaviour of the disk is mysterious. If it was like you said, then the disk would be dead all the time, but as I described before sometimes it was possbile to detect it despite this failure. Someone designed it that way, but perhaps there are ways to come round it. a. |
#8
|
|||
|
|||
"andy" wrote in message ... Thanks for your reply. If it was an electronic failure then such behaviour would be obious, but why the same happens with some mechanical failures? When electronics is working in my opinion it still should be detected by bios and/or the system (win xp or linux), but often it is not. What on earth for? Such would be highly misleading and a very poor design choice. But I could then recover 80% of my data, and now I can recover 0% of my data. Does it make sense for you now? Perfect sense and no you couldn't recover 80% of your data. Is there any way to disable that feature? (I mean to make the malfunctioned HDD visible to the system again?) The drive is DOA! Don't get DOA. Dead On Arrival |
#9
|
|||
|
|||
"andy" wrote in message ... On Fri, 3 Sep 2004 11:24:48 +0200, "Joep" j o e p @ d i y d a t a r e c o v e r y . n l wrote: "andy" wrote in message .. . *Sometimes* ... So, maybe it's the nature of the problem that prevents the disk from being detected. Failure to mechanics seems to be the problem causing the non-detection problem. Unfortunatelly the "sometimes" is now "nearly always". How do you know? How did you come up with the 80%? When the disk was detectable then about 20% of files could not be read. This was not because bad sectors (the disk did not have any AFAIK), but because of the mechanics failure (when it started to have the symptoms of the failure also 20% of data became unavailable). No, now 100% is unavailable. You should try to clone it as long as you can see it. However, every read may worsen the condition of the disk, in general it is advised to cease DIY recovery attempts (if the data is important to you) when a disk is maing unusual and scary noises. Yes, it seems that the condition very quickly became much worse. Isn't that what I said. |
#10
|
|||
|
|||
"CJT" wrote in message ... andy wrote: Hi! Could someone please explain why in the case of *mechanical* failure HD becomes sometimes undetected by BIOS and/or the operating system (e.g. win xp or linux)? If it was an electronic failure then such behaviour would be obious, but why the same happens with some mechanical failures? When electronics is working in my opinion it still should be detected by bios and/or the system (win xp or linux), but often it is not. I could recover about 80% of the data from my HDD (which apparently has a mechanical failure - plates spin up and down, heads create bad noises) if only the disk could be seen by the system all the time. But often during copying of the data heads hit with a loud sound so badly that sometimes even the plates stop rotating, and the disk then dissapears from the system. It is then very difficult to make it detectable by the system again, sometimes the sytem can detect it but only after several minutes of copying it freezes and then dissapears again. Recently, I was unlucky, and even after several dozens of retries it's still undetectable by the system. Could you please advice what to do to make the disk detectable by the system all the time? What causes that it is not detectable although the failure is in mechanics not electronics? BTW, if someone has the same disk model (Quantum Fireball ST64A011), please let me know. andy Maybe it stores part of its own software on the platters. Most all current HDs do that. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Why mechanical failure causes HDD being undetectable by bios or OS ? | andy | General | 32 | September 8th 04 09:01 PM |
Why mechanical failure causes HDD being undetectable by bios or OS ? | andy | General | 0 | September 3rd 04 04:02 AM |
Weird Msg. - FDC Failure | Marilyn E. Burford | Dell Computers | 1 | July 11th 04 02:37 AM |
SATA raid: single point of failure? | Jim Wall | Storage & Hardrives | 4 | June 10th 04 10:35 AM |
Boot Failure 700xl | Don Crano | Gateway Computers | 6 | November 18th 03 01:39 AM |