If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Gigabyte P35-DS3P
Where is the ram frequency on this mobo bios? I am looking in the
M.I.T. section and can't see it at all. |
#2
|
|||
|
|||
Gigabyte P35-DS3P
On 19 Jan, 00:49, bornfree wrote:
Where is the ram frequency on this mobo bios? I am looking in the M.I.T. section and can't see it at all. Well I see it, but it is greyed out. |
#3
|
|||
|
|||
Gigabyte P35-DS3P
On 19 Jan, 01:11, bornfree wrote:
On 19 Jan, 00:49, bornfree wrote: Where is the ram frequency on this mobo bios? I am looking in the M.I.T. section and can't see it at all. Well I see it, but it is greyed out. Ok nevermind. I'm a doofus. (apparently the way to overclock these boards is by using the DRAM multi.) I have an Intel E6300 (1.86Ghz stock) with my Gigabyte P35-DS3P. Can anyone recommend a good starting overclock? |
#4
|
|||
|
|||
Gigabyte P35-DS3P
"bornfree" wrote in message ...
On 19 Jan, 01:11, bornfree wrote: On 19 Jan, 00:49, bornfree wrote: Where is the ram frequency on this mobo bios? I am looking in the M.I.T. section and can't see it at all. Well I see it, but it is greyed out. Ok nevermind. I'm a doofus. (apparently the way to overclock these boards is by using the DRAM multi.) I have an Intel E6300 (1.86Ghz stock) with my Gigabyte P35-DS3P. Can anyone recommend a good starting overclock? 1.87GHz ;-) Seriously, even though it's a different motherboard, read through this info on bios settings, voltages etc: http://www.xbitlabs.com/articles/cpu...o-e6300_8.html The cpu itself is a good overclocker, but you may run into other limiting factors far short of what it's capable of. |
#5
|
|||
|
|||
Gigabyte P35-DS3P
bornfree wrote:
Where is the ram frequency on this mobo bios? I am looking in the M.I.T. section and can't see it at all. Like the rest of the Gigabyte boards I've seen, it's probably hidden to annoy and confound users. After first entering the BIOS setup, press Ctrl + F1 and one of the menus will have more advanced tweaking options. http://hardwarelogic.com/news/132/AR...007-08-17.html |
#6
|
|||
|
|||
Gigabyte P35-DS3P
Fishface wrote:
bornfree wrote: Where is the ram frequency on this mobo bios? I am looking in the M.I.T. section and can't see it at all. Like the rest of the Gigabyte boards I've seen, it's probably hidden to annoy and confound users. After first entering the BIOS setup, press Ctrl + F1 and one of the menus will have more advanced tweaking options. http://hardwarelogic.com/news/132/AR...007-08-17.html Ok I have worked the FSB(?) up to 300, and let the bios decide what was best for the ram. It set it to 750. Running nice. A bit faster. Hotter, but cooler is ok. Stable so far.. will run prime tonight. CPUID still reports my clock speed to be 1.86 under "specification" though . |
#7
|
|||
|
|||
Gigabyte P35-DS3P
bornfree wrote:
CPUID still reports my clock speed to be 1.86 under "specification" though . If SpeedStep is enabled, it will automatically slow down under load. Some report higher overclocks when this is disabled, as it lowers the voltage (vCore) also. Check it with a load. Which CPU do you have? If multi-core, sure it is stressing all cores by checking the performance tab of Windows Task Manager, assuming you are running Windows, of course. I just use this: http://www.techpowerup.com/downloads...rime_2004.html ....which runs two instances of Prime95 torture test. I need to run two instances of Orthos for the Quad core, though. Shaun posted that he found a Prime95 version on www.MajorGeeks.com which is ver 25.5. that would stress all cores. I was a little suspicious that it wasn't found on the official website, so I didn't download it. http://www.mersenne.org/freesoft.htm |
#8
|
|||
|
|||
Gigabyte P35-DS3P
On 19 Jan, 22:43, "Fishface" ? wrote:
bornfree wrote: CPUID still reports my clock speed to be 1.86 under "specification" though . If SpeedStep is enabled, it will automatically slow down under load. Some report higher overclocks when this is disabled, as it lowers the voltage (vCore) also. Check it with a load. Which CPU do you have? E6300. 2 cores. See this pic it shows my system as defined by CPU ID and prime95. http://i1.tinypic.com/6ww5qht.png |
#9
|
|||
|
|||
Gigabyte P35-DS3P
On 19 Jan, 22:43, "Fishface" ? wrote:
bornfree wrote: CPUID still reports my clock speed to be 1.86 under "specification" though . If SpeedStep is enabled, it will automatically slow down under load. Some report higher overclocks when this is disabled, as it lowers the voltage (vCore) also. Check it with a load. Which CPU do you have? If multi-core, sure it is stressing all cores by checking the performance tab of Windows Task Manager, Orthos running + Windows Performace tab + temps. http://i11.tinypic.com/850vlts.png CPU got a bit hot. (Idle temp around 54/55) |
#10
|
|||
|
|||
Gigabyte P35-DS3P
On 20 Jan, 00:02, "RobV" wrote:
bornfree wrote: On 19 Jan, 22:43, "Fishface" ? wrote: bornfree wrote: CPUID still reports my clock speed to be 1.86 under "specification" though . If SpeedStep is enabled, it will automatically slow down under load. Some report higher overclocks when this is disabled, as it lowers the voltage (vCore) also. Check it with a load. Which CPU do you have? E6300. 2 cores. See this pic it shows my system as defined by CPU ID and prime95. http://i1.tinypic.com/6ww5qht.png It's Intel's attempt to confuse you. ;-) In CPU-Z (and anywhere else, AFAIK), Intel CPUs are identified by the model number * and * the stock frequency. As shown in CPU-Z, Specification, you have a 6300 @ 1.86GHz. I have a 6600, which shows up in CPU-Z, Specification, as a 6600 @ 2.4GHz Lower down at Core Speed, the actual clock speed of the CPU is listed. Mine is 3006 MHz. The spec and CPU information will always show 6600 @ 2.4GHz, even if the CPU actual clock speed is higher (or lower). Now, to your system. You have the Core Voltage set to 1.408V (don't know if that's under load, or not). Lower left side, Core Speed is 1800 MHz, or 1.8 GHz, so you're underclocking the CPU. Just below, you'll see why. The multiplier is x6.0 and the FSB is 300 MHz, for an * effective * FSB (x4, or Quad Pumped) of 1200 MHz. CPU speed is x6.0 X 300 MHz FSB, which equals 1800 MHz. Unless you set the multiplier to x6 (the lowest, I believe), it was set by Speed Step, which Fishface mentioned. In BIOS, go to the Advanced tab, open CPU Configuration and disable Modify Ratio Support, then set it to the max value (or vice versa). Disable C1E Disable Intel Speed Step at the very bottom. This should give you a stable multiplier and Vcore so you can actually test the limits of the CPU, without Speed Step changing things on you. Ok. First of all, I need to say I am a beginner at this so I didn't understand everything you said. Secondly, prime says my CPU is 2100Mhz. Mobmeter also says 2.10Ghz.... I can't have underclocked it, because my CPU temp is way higher than previous. Ok I got it. Here it is under load: http://i18.tinypic.com/82w528j.png |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Gigabyte GA-P35-DS3P BIOS beep codes not documented, CPU problems | RoundSparrow | Gigabyte Motherboards | 3 | August 10th 07 07:58 PM |
Gigabyte DS3P S3 standby issue | alfhenrik | Gigabyte Motherboards | 6 | August 8th 07 07:14 AM |
Gigabyte ga-p35-ds3p hyperthreading | verukins | Gigabyte Motherboards | 1 | July 15th 07 08:35 AM |
2GB Kit recommendation for GA-P35-DS3P | 007[_3_] | Gigabyte Motherboards | 4 | May 15th 07 01:52 PM |