If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Critical errors? ATA Error Count
I have a brand new Samsung SP1614N and noticed that the ATA Errors
increase from hour to hour. ATA Error Count: 12800 (device log contains only the most recent five errors) I think this is no good sign too? 195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 192199876 Self-Test show no errors. So is there a problem with the interface? For more details see below. Al smartctl -a /dev/hda smartctl version 5.30 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: SAMSUNG SP1614N Firmware Version: TM100-24 Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 Local Time is: Sun Jun 13 13:09:24 2004 CEST == WARNING: May need -F samsung or -F samsung2 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (5760) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 96) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 3 3 Spin_Up_Time 0x0007 065 065 000 Pre-fail Always - 6016 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 37 5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0024 253 253 000 Old_age Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 7958 10 Spin_Retry_Count 0x0013 253 253 049 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 24 194 Temperature_Celsius 0x0022 130 088 000 Old_age Always - 36 195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 192199876 196 Reallocated_Event_Count 0x0012 253 253 000 Old_age Always - 0 197 Current_Pending_Sector 0x0033 253 253 010 Pre-fail Always - 0 198 Offline_Uncorrectable 0x0031 253 253 010 Pre-fail Offline - 0 199 UDMA_CRC_Error_Count 0x000b 100 100 051 Pre-fail Always - 0 200 Multi_Zone_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 201 Soft_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 SMART Error Log Version: 1 ATA Error Count: 12800 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Timestamp = decimal seconds since the previous disk power-on. Note: timestamp "wraps" after 2^32 msec = 49.710 days. Error 12800 occurred at disk power-on lifetime: 55 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers we ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 8f ba 1d e0 Error: ABRT Commands leading to the command that caused the error we CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- ef 85 00 8f ba 1d e0 00 110.000 SET FEATURES [Disable APM] b0 d5 01 01 4f c2 e0 00 85.500 SMART READ LOG b0 d5 01 06 4f c2 e0 00 85.500 SMART READ LOG b0 d0 01 00 4f c2 e0 00 85.438 SMART READ DATA b0 da 00 00 4f c2 00 00 85.000 SMART RETURN STATUS Error 12799 occurred at disk power-on lifetime: 55 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers we ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 8f ba 1d e0 Error: ABRT Commands leading to the command that caused the error we CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- ef 85 00 8f ba 1d e0 00 115.125 SET FEATURES [Disable APM] b0 d5 01 01 4f c2 e0 00 90.563 SMART READ LOG b0 d5 01 06 4f c2 e0 00 90.500 SMART READ LOG b0 d0 01 00 4f c2 e0 00 90.438 SMART READ DATA b0 da 00 00 4f c2 00 00 90.063 SMART RETURN STATUS Error 12798 occurred at disk power-on lifetime: 55 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers we ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 af d0 84 e0 Error: ABRT Commands leading to the command that caused the error we CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- ef 85 00 af d0 84 e0 00 7894.875 SET FEATURES [Disable APM] b0 d5 01 01 4f c2 e0 00 7869.500 SMART READ LOG b0 d5 01 06 4f c2 e0 00 7869.500 SMART READ LOG b0 d0 01 00 4f c2 e0 00 7869.438 SMART READ DATA b0 da 00 00 4f c2 00 00 7869.000 SMART RETURN STATUS Error 12797 occurred at disk power-on lifetime: 53 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers we ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 8f ba 1d e0 Error: ABRT Commands leading to the command that caused the error we CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- ef 85 00 8f ba 1d e0 00 113.875 SET FEATURES [Disable APM] b0 d5 01 01 4f c2 e0 00 108.750 SMART READ LOG b0 d5 01 06 4f c2 e0 00 108.688 SMART READ LOG b0 d0 01 00 4f c2 e0 00 108.500 SMART READ DATA b0 da 00 00 4f c2 00 00 107.938 SMART RETURN STATUS Error 12796 occurred at disk power-on lifetime: 53 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers we ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 8f ba 1d e0 Error: ABRT Commands leading to the command that caused the error we CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- ef 85 00 8f ba 1d e0 00 19088.625 SET FEATURES [Disable APM] b0 d5 01 01 4f c2 e0 00 19085.250 SMART READ LOG b0 d5 01 06 4f c2 e0 00 19085.125 SMART READ LOG b0 d0 01 00 4f c2 e0 00 19085.000 SMART READ DATA b0 da 00 00 4f c2 00 00 19084.313 SMART RETURN STATUS SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 57 - # 2 Short offline Completed without error 00% 54 - # 3 Short offline Completed without error 00% 37 - # 4 Short offline Completed without error 00% 28 - # 5 Extended offline Completed without error 00% 16 - # 6 Short offline Completed without error 00% 13 - |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
C1 and C2 errors | James Perrett | Cdr | 10 | April 14th 04 08:08 AM |
Solution for strange graphics errors (long) | Henrik Stavnshøj | Ati Videocards | 0 | April 9th 04 12:21 PM |
Can't install any OS (hardware fault?) | Paul Richard | Homebuilt PC's | 4 | September 27th 03 12:55 PM |
How concerned should I be about these Nero CD-Speed C2 errors? | Robert Hancock | Cdr | 5 | August 19th 03 12:34 AM |
Update: Memtest86 errors | Bob Davis | Gigabyte Motherboards | 2 | August 3rd 03 06:27 AM |