If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Storageworks 4314R Enclosure Management
I have a Compaq Storageworks 4314R Enclosure attached to a Compaq Smart
Array 5304 RAID controller running in a non-HP server (similar specs to a DL385). I have downloaded and installed both the "Array Configuration Utility V7.5" and the "Array Diagnostic Utility V7.5" and I can manage and report on the volumes attached to the RAID controller (both in the server and the enclosure). My problem is I want to be able to monitor the disk fail events and the environmental conditions of the 4314R enclosure. I checked out the quickspecs for the 4314 enclosure and it supports both "Compaq StorageWorks Command Console" and "HP Systems Insight Manager". After much searching I was able to find and download a version 2.1 of the SWCC but it could not even see the enclosure I then download and installed (after removing SWCC) the lastest version of Systems Insight Manager. Although it looked good I was unable to find even where the module was to manage storage enclosures is. What I am wondering is what software I need to be able to monitor the environment of the 4314R via its EMU and trigger events(eg. Event Log Entried and emails) when things happen? |
#2
|
|||
|
|||
Storageworks 4314R Enclosure Management
wrote in message ups.com... I have a Compaq Storageworks 4314R Enclosure attached to a Compaq Smart Array 5304 RAID controller running in a non-HP server (similar specs to a DL385). I have downloaded and installed both the "Array Configuration Utility V7.5" and the "Array Diagnostic Utility V7.5" and I can manage and report on the volumes attached to the RAID controller (both in the server and the enclosure). My problem is I want to be able to monitor the disk fail events and the environmental conditions of the 4314R enclosure. I checked out the quickspecs for the 4314 enclosure and it supports both "Compaq StorageWorks Command Console" and "HP Systems Insight Manager". After much searching I was able to find and download a version 2.1 of the SWCC but it could not even see the enclosure I then download and installed (after removing SWCC) the lastest version of Systems Insight Manager. Although it looked good I was unable to find even where the module was to manage storage enclosures is. What I am wondering is what software I need to be able to monitor the environment of the 4314R via its EMU and trigger events(eg. Event Log Entried and emails) when things happen? Im pretty sure that you have to be running the Foundation Agents, and the requisite Storage Agents. But guess what ... they dont run on Non-HPaq systems. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
What to look for in an empty StorageWorks 4314R enclosure? | Rick F. | Compaq Servers | 0 | January 19th 06 05:41 PM |
Newbie: OC Advice: AMDXP2200 CPU | Donald Bock | Overclocking AMD Processors | 2 | March 12th 05 12:14 AM |
Enterprise Storage Management (ESM) FAQ Revision 2004/06/23 - Part 1/1 | Will Spencer | Storage & Hardrives | 0 | June 23rd 04 06:58 AM |
Enterprise Storage Management (ESM) FAQ Revision 2004/04/11 - Part 1/1 | Will Spencer | Storage & Hardrives | 0 | April 11th 04 07:24 AM |
Enterprise Storage Management (ESM) FAQ Revision 2004/02/16 - Part 1/1 | Will Spencer | Storage & Hardrives | 0 | February 16th 04 09:23 PM |