If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
GA-7n400 Pro Video Post Issue
Components:
GA-7n400 Pro, 1600 Athon AMD(1400mhz), 2x256 3200 Geforce2Mx400 I can get the cpu fans spinning, the board is showing a orange light near the agp slot, I read in the manual that the motherboard doesnt support 3v 2XAgp cards, does this apply to my card? I have tried using my voodoo3 pci card but it will also not boot, I have set the CLK_RATIO to AUTO and CLK_SW to On, any suggestions would be greatly apreciated, thank you. ============== Posted through www.HowToFixComputers.com/bb - free access to hardware troubleshooting newsgroups. |
#2
|
|||
|
|||
Sto wrote:
Components: GA-7n400 Pro, 1600 Athon AMD(1400mhz), 2x256 3200 Geforce2Mx400 I can get the cpu fans spinning, the board is showing a orange light near the agp slot, I read in the manual that the motherboard doesnt support 3v 2XAgp cards, does this apply to my card? I have tried using my voodoo3 pci card but it will also not boot, I have set the CLK_RATIO to AUTO and CLK_SW to On, any suggestions would be greatly apreciated, thank you. ============== Posted through www.HowToFixComputers.com/bb - free access to hardware troubleshooting newsgroups. Did you plug in the 12v additional power plug into the board? - I forgot that when I did mine and it has the same effect. Two power feeds go into it. |
#3
|
|||
|
|||
Awesome it worked! But I can't get it to run without having the CLK_SW
on the off position thus setting the fsb to 100mhz (therfore the speed is at 1100mhz). When the CLK_SW is set to On and I configure the fsb speed it won't post video... atleast I have it running ============== Posted through www.HowToFixComputers.com/bb - free access to hardware troubleshooting newsgroups. |
#4
|
|||
|
|||
only 4x and 8x supported as on the first page of the manual
K.K. "Sto" wrote in message ... Components: GA-7n400 Pro, 1600 Athon AMD(1400mhz), 2x256 3200 Geforce2Mx400 I can get the cpu fans spinning, the board is showing a orange light near the agp slot, I read in the manual that the motherboard doesnt support 3v 2XAgp cards, does this apply to my card? I have tried using my voodoo3 pci card but it will also not boot, I have set the CLK_RATIO to AUTO and CLK_SW to On, any suggestions would be greatly apreciated, thank you. ============== Posted through www.HowToFixComputers.com/bb - free access to hardware troubleshooting newsgroups. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
No POST Beeps, No Video | Bryan R. Meyer | Homebuilt PC's | 6 | January 30th 04 09:17 PM |
7N400 pro2 video card? | mailman | Gigabyte Motherboards | 0 | January 24th 04 12:00 PM |
CPU Issue with MSN Messenger? (repeat post) | Michael Anthony | General | 6 | December 17th 03 12:29 PM |
7N400 Pro 2 audio and video | Phil Wolfe | Gigabyte Motherboards | 6 | October 31st 03 04:55 PM |
No POST & no video signal - Broken motherboard? | Paul Mc | Homebuilt PC's | 6 | September 30th 03 07:43 PM |