If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Alert at bootup
I really had 2 questions: (BIOS bootup alert & Event Viewer alert)
I am getting a message before windows loads (so cannot do a printscreen) just following choosing WindowsXP as operating system (using dual boot to W2k) that states this: BIOS: BIOS update data incorrect. CPUID=00000F27, PCI Device Listing... (then it lists my devices and other info including IRQ, etc.) and continues to load windows with no obvious problems. However, I am getting many instances of Error in Event Viewer that reports this: The device, \Device\Harddisk1\D, has a bad block. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. (This link tells me I should replace my hard drive.) This has been coming up ever since I installed this P4S333 motherboard almost a yr. ago. I haven't flashed the bios on this motherboard, ACPI BIOS Revision 1006C, since I bought it. Could a message like this BIOS: be causing my Event Viewer to report a bad sector on my Maxtor hard drive? or doesn't this BIOS message have ANYTHING to do with the Event Viewer message? I have done a Scan on the hard drive, have used Partition Magic to scan and fix it, and also have used the Maxtor.exe file that came with the drive to do 5 surface scans and nothing reports bad sectors to fix, only Event Viewer is. Could anyone tell me if Event Viewer is reporting an accurate message and should the CPUID=00000F27 mean anything to me? TIA for any advice, katy |
#2
|
|||
|
|||
In article , "Katy"
wrote: I really had 2 questions: (BIOS bootup alert & Event Viewer alert) I am getting a message before windows loads (so cannot do a printscreen) just following choosing WindowsXP as operating system (using dual boot to W2k) that states this: BIOS: BIOS update data incorrect. CPUID=3D00000F27, PCI Device Listing... (then it lists my devices and other info including IRQ, etc.) and continues to load windows with no obvious problems. However, I am getting many instances of Error in Event Viewer that reports this: The device, \Device\Harddisk1\D, has a bad block. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. (This link tells me I should replace my hard drive.) This has been coming up ever since I installed this P4S333 motherboard almost a yr. ago. I haven't flashed the bios on this motherboard, ACPI BIOS Revision 1006C, since I bought it. Could a message like this BIOS: be causing my Event Viewer to report a bad sector on my Maxtor hard drive? or doesn't this BIOS message have ANYTHING to do with the Event Viewer message? I have done a Scan on the hard drive, have used Partition Magic to scan and fix it, and also have used the Maxtor.exe file that came with the drive to do 5 surface scans and nothing reports bad sectors to fix, only Event Viewer is. Could anyone tell me if Event Viewer is reporting an accurate message and should the CPUID=3D00000F27 mean anything to me? TIA for any advice, katy Intel has a scheme, where they can repair certain bugs in the processor with what is called a "microcode update". Some of the bugs will only be discovered after the processor is shipping and in the field, so Intel issues new microcode files whenever a bug is found. The BIOS contains a microcode loader. The BIOS also has a set of 2KB microcode files, to load. The microcode files have ID info, like the family code 0F27. When Asus gets updated microcode from Intel, they incorporate the new 2KB patches into new BIOS releases. Flashing the BIOS is one way to get microcode for your 0F27 processor. Another method that works at the BIOS level, is CTMC. This is a program from CT Heise magazine in Germany. The MC stands for microcode. The nice thing about the CTMC method, is there is less risk to the BIOS chip. A volatile region of the flash chip is used, and no BIOS executable code is touched, so the machine should be able to boot, no matter how well the CTMC program works. CTMC uses a hook in the BIOS, so the flashing of the BIOS is being done by the BIOS itself. ftp://ftp.heise.de/pub/ct/ctsi/ctmc10.zip Basically, this is a capsule summary of using CTMC: 1) You have to be able to boot Windows to use the program. That is because you need to run the CTMC program to do the actual writing of microcode to the flash chip. If not, then download the latest BIOS file from Asus, the latest MSDOS boot floppy based flash program from Asus, read any warnings on the download page, and flash the BIOS. 2) Find a recent version of BIOS from the download page. If your processor version was never supported by Asus ever, you can download a BIOS from another board that uses an Intel P4 processor, provided it is an Award BIOS, and extract microcode from that BIOS file. 3) Get the CTMC package. Use splitawd to split the donor BIOS file into modules. Use LHA to decompress a module called "cpucode.exe". Use the main CTMC program "ctmc cpucode.exe /store" This gives a bunch of 2KB files, and the file name will have the processor family code in it, like 0F270433.bin or the like. Now, use a MSDOS window or a command prompt window in Windows, run ctmc again, this time using the option to write the donated microcode to the BIOS "ctmc 0f270433.bin /write". Reboot. The BIOS message should disappear after that, and the Intel FrequencyID utility should change the processor version listed from 0 to whatever version was in the microcode patch (0x33 in the example above - the version is part of the file name). So, that covers two methods. Either flash the whole BIOS chip using the latest from Asus, or use CTMC to only flash the needed 2KB of microcode to the flash chip. (The 1008c005.zip beta BIOS contains 0F270433.BIN microcode, so that BIOS will certainly fix the problem, or you can use that BIOS file to extract 0F270433.BIN for a "ctmc 0F270433.BIN /store" operation.) In the later Microsoft OSes, there is also a microcode loader in the OS itself. When say, WinXP boots, it can load a microcode update to the system, in which case the bugs in the processor are "removed" after the update.sys runs. But, this method leaves a gap, that extends from POST, until update.sys runs. You say your errors exist even after WinXP boots. I would think the microcode update in Windows would remove the microcode as an issue, so something else must be wrong. HTH, Paul |
#3
|
|||
|
|||
Thanks Paul! Now I wonder if I download the bios flash from Asus he
http://www.asus.com/support/download...S333&Type=BIOS I read in my manual that the Aflash is a 'writer utility' that uploads the flash file to the bios to update it. so I would download the Aflash.zip and the 1007 file, both, right? and how do I know if I need the 1007 or the 1007c? I went into my setup and according to the manaul and comparing it to my bios, I have no line allowing me to enable or disable "Onboard LAN Boot ROM' nor do I have a line allowing me to enable or disable 'Onboard LAN Controller'. Would this mean I would use the P4S1007.zip? and not the 'c' version? I looked at the file link you sent below for the CTMC, downloaded it, and the text file was in German, the other text file was just numbers. I guess if I'm going to do that, I may as well flash the bios to do it and allow for a larger than 137gb hard drive at the same time. I went to the link you sent to an earlier question that led me to '48bitLBA.com' and chose the Upgrade Bios NOW and the tech who called informed me at that time it would cost me $50 for their bios upgrade. I had downloaded, installed and run the Bios Agent creating a text file that I am probably not allowed to attach, and I was supposed to call the place to install it. Couldn't I download/install this myself free of charge from Asus? I have flashed a bios once before on a PB which was very involved and irritating, this motherboard seems easier but I just want to be sure I have the right file for this mobo. Would be great if Asus could use a Bios Agent to tell 'me' what I need. Could you help me find the right file? I understand that the responsibility is still in my court and I'm not about to make you or anyone responsible for the 'correct file' but I sure could use some feedback. Thanks again for helping and welcome any advice!!! katy "Paul" wrote in message ... In article , "Katy" wrote: I really had 2 questions: (BIOS bootup alert & Event Viewer alert) I am getting a message before windows loads (so cannot do a printscreen) just following choosing WindowsXP as operating system (using dual boot to W2k) that states this: BIOS: BIOS update data incorrect. CPUID=3D00000F27, PCI Device Listing... (then it lists my devices and other info including IRQ, etc.) and continues to load windows with no obvious problems. However, I am getting many instances of Error in Event Viewer that reports this: The device, \Device\Harddisk1\D, has a bad block. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. (This link tells me I should replace my hard drive.) This has been coming up ever since I installed this P4S333 motherboard almost a yr. ago. I haven't flashed the bios on this motherboard, ACPI BIOS Revision 1006C, since I bought it. Could a message like this BIOS: be causing my Event Viewer to report a bad sector on my Maxtor hard drive? or doesn't this BIOS message have ANYTHING to do with the Event Viewer message? I have done a Scan on the hard drive, have used Partition Magic to scan and fix it, and also have used the Maxtor.exe file that came with the drive to do 5 surface scans and nothing reports bad sectors to fix, only Event Viewer is. Could anyone tell me if Event Viewer is reporting an accurate message and should the CPUID=3D00000F27 mean anything to me? TIA for any advice, katy Intel has a scheme, where they can repair certain bugs in the processor with what is called a "microcode update". Some of the bugs will only be discovered after the processor is shipping and in the field, so Intel issues new microcode files whenever a bug is found. The BIOS contains a microcode loader. The BIOS also has a set of 2KB microcode files, to load. The microcode files have ID info, like the family code 0F27. When Asus gets updated microcode from Intel, they incorporate the new 2KB patches into new BIOS releases. Flashing the BIOS is one way to get microcode for your 0F27 processor. Another method that works at the BIOS level, is CTMC. This is a program from CT Heise magazine in Germany. The MC stands for microcode. The nice thing about the CTMC method, is there is less risk to the BIOS chip. A volatile region of the flash chip is used, and no BIOS executable code is touched, so the machine should be able to boot, no matter how well the CTMC program works. CTMC uses a hook in the BIOS, so the flashing of the BIOS is being done by the BIOS itself. ftp://ftp.heise.de/pub/ct/ctsi/ctmc10.zip Basically, this is a capsule summary of using CTMC: 1) You have to be able to boot Windows to use the program. That is because you need to run the CTMC program to do the actual writing of microcode to the flash chip. If not, then download the latest BIOS file from Asus, the latest MSDOS boot floppy based flash program from Asus, read any warnings on the download page, and flash the BIOS. 2) Find a recent version of BIOS from the download page. If your processor version was never supported by Asus ever, you can download a BIOS from another board that uses an Intel P4 processor, provided it is an Award BIOS, and extract microcode from that BIOS file. 3) Get the CTMC package. Use splitawd to split the donor BIOS file into modules. Use LHA to decompress a module called "cpucode.exe". Use the main CTMC program "ctmc cpucode.exe /store" This gives a bunch of 2KB files, and the file name will have the processor family code in it, like 0F270433.bin or the like. Now, use a MSDOS window or a command prompt window in Windows, run ctmc again, this time using the option to write the donated microcode to the BIOS "ctmc 0f270433.bin /write". Reboot. The BIOS message should disappear after that, and the Intel FrequencyID utility should change the processor version listed from 0 to whatever version was in the microcode patch (0x33 in the example above - the version is part of the file name). So, that covers two methods. Either flash the whole BIOS chip using the latest from Asus, or use CTMC to only flash the needed 2KB of microcode to the flash chip. (The 1008c005.zip beta BIOS contains 0F270433.BIN microcode, so that BIOS will certainly fix the problem, or you can use that BIOS file to extract 0F270433.BIN for a "ctmc 0F270433.BIN /store" operation.) In the later Microsoft OSes, there is also a microcode loader in the OS itself. When say, WinXP boots, it can load a microcode update to the system, in which case the bugs in the processor are "removed" after the update.sys runs. But, this method leaves a gap, that extends from POST, until update.sys runs. You say your errors exist even after WinXP boots. I would think the microcode update in Windows would remove the microcode as an issue, so something else must be wrong. HTH, Paul |
#4
|
|||
|
|||
Katy,
Greetings and hallucinations from just north of Fantasy Land (Washington, DC)! It depends on whether you have a built in LAN (network) "card" or not. With the "card" flash 1008. Without the LAN, flash 1008c. Peace, Paul "Katy" wrote in message ... Thanks Paul! Now I wonder if I download the bios flash from Asus he http://www.asus.com/support/download...S333&Type=BIOS I read in my manual that the Aflash is a 'writer utility' that uploads the flash file to the bios to update it. so I would download the Aflash.zip and the 1007 file, both, right? and how do I know if I need the 1007 or the 1007c? I went into my setup and according to the manaul and comparing it to my bios, I have no line allowing me to enable or disable "Onboard LAN Boot ROM' nor do I have a line allowing me to enable or disable 'Onboard LAN Controller'. Would this mean I would use the P4S1007.zip? and not the 'c' version? I looked at the file link you sent below for the CTMC, downloaded it, and the text file was in German, the other text file was just numbers. I guess if I'm going to do that, I may as well flash the bios to do it and allow for a larger than 137gb hard drive at the same time. I went to the link you sent to an earlier question that led me to '48bitLBA.com' and chose the Upgrade Bios NOW and the tech who called informed me at that time it would cost me $50 for their bios upgrade. I had downloaded, installed and run the Bios Agent creating a text file that I am probably not allowed to attach, and I was supposed to call the place to install it. Couldn't I download/install this myself free of charge from Asus? I have flashed a bios once before on a PB which was very involved and irritating, this motherboard seems easier but I just want to be sure I have the right file for this mobo. Would be great if Asus could use a Bios Agent to tell 'me' what I need. Could you help me find the right file? I understand that the responsibility is still in my court and I'm not about to make you or anyone responsible for the 'correct file' but I sure could use some feedback. Thanks again for helping and welcome any advice!!! katy "Paul" wrote in message ... In article , "Katy" wrote: I really had 2 questions: (BIOS bootup alert & Event Viewer alert) I am getting a message before windows loads (so cannot do a printscreen) just following choosing WindowsXP as operating system (using dual boot to W2k) that states this: BIOS: BIOS update data incorrect. CPUID=3D00000F27, PCI Device Listing... (then it lists my devices and other info including IRQ, etc.) and continues to load windows with no obvious problems. However, I am getting many instances of Error in Event Viewer that reports this: The device, \Device\Harddisk1\D, has a bad block. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. (This link tells me I should replace my hard drive.) This has been coming up ever since I installed this P4S333 motherboard almost a yr. ago. I haven't flashed the bios on this motherboard, ACPI BIOS Revision 1006C, since I bought it. Could a message like this BIOS: be causing my Event Viewer to report a bad sector on my Maxtor hard drive? or doesn't this BIOS message have ANYTHING to do with the Event Viewer message? I have done a Scan on the hard drive, have used Partition Magic to scan and fix it, and also have used the Maxtor.exe file that came with the drive to do 5 surface scans and nothing reports bad sectors to fix, only Event Viewer is. Could anyone tell me if Event Viewer is reporting an accurate message and should the CPUID=3D00000F27 mean anything to me? TIA for any advice, katy Intel has a scheme, where they can repair certain bugs in the processor with what is called a "microcode update". Some of the bugs will only be discovered after the processor is shipping and in the field, so Intel issues new microcode files whenever a bug is found. The BIOS contains a microcode loader. The BIOS also has a set of 2KB microcode files, to load. The microcode files have ID info, like the family code 0F27. When Asus gets updated microcode from Intel, they incorporate the new 2KB patches into new BIOS releases. Flashing the BIOS is one way to get microcode for your 0F27 processor. Another method that works at the BIOS level, is CTMC. This is a program from CT Heise magazine in Germany. The MC stands for microcode. The nice thing about the CTMC method, is there is less risk to the BIOS chip. A volatile region of the flash chip is used, and no BIOS executable code is touched, so the machine should be able to boot, no matter how well the CTMC program works. CTMC uses a hook in the BIOS, so the flashing of the BIOS is being done by the BIOS itself. ftp://ftp.heise.de/pub/ct/ctsi/ctmc10.zip Basically, this is a capsule summary of using CTMC: 1) You have to be able to boot Windows to use the program. That is because you need to run the CTMC program to do the actual writing of microcode to the flash chip. If not, then download the latest BIOS file from Asus, the latest MSDOS boot floppy based flash program from Asus, read any warnings on the download page, and flash the BIOS. 2) Find a recent version of BIOS from the download page. If your processor version was never supported by Asus ever, you can download a BIOS from another board that uses an Intel P4 processor, provided it is an Award BIOS, and extract microcode from that BIOS file. 3) Get the CTMC package. Use splitawd to split the donor BIOS file into modules. Use LHA to decompress a module called "cpucode.exe". Use the main CTMC program "ctmc cpucode.exe /store" This gives a bunch of 2KB files, and the file name will have the processor family code in it, like 0F270433.bin or the like. Now, use a MSDOS window or a command prompt window in Windows, run ctmc again, this time using the option to write the donated microcode to the BIOS "ctmc 0f270433.bin /write". Reboot. The BIOS message should disappear after that, and the Intel FrequencyID utility should change the processor version listed from 0 to whatever version was in the microcode patch (0x33 in the example above - the version is part of the file name). So, that covers two methods. Either flash the whole BIOS chip using the latest from Asus, or use CTMC to only flash the needed 2KB of microcode to the flash chip. (The 1008c005.zip beta BIOS contains 0F270433.BIN microcode, so that BIOS will certainly fix the problem, or you can use that BIOS file to extract 0F270433.BIN for a "ctmc 0F270433.BIN /store" operation.) In the later Microsoft OSes, there is also a microcode loader in the OS itself. When say, WinXP boots, it can load a microcode update to the system, in which case the bugs in the processor are "removed" after the update.sys runs. But, this method leaves a gap, that extends from POST, until update.sys runs. You say your errors exist even after WinXP boots. I would think the microcode update in Windows would remove the microcode as an issue, so something else must be wrong. HTH, Paul |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help? P4P800 Really slow bootup - a lot of HDD activity before WinXP is usable... | William Cheng | Homebuilt PC's | 13 | December 1st 04 08:26 PM |
HP PSC2510 software reinstalls itself on bootup! | Graham Moore | Homebuilt PC's | 1 | October 14th 04 03:05 AM |
Error message at bootup - Gearsec (XP Pro) | Arawak | Cdr | 1 | September 26th 04 06:03 AM |
NO GO with 3 Optical Drives at bootup! | Mattrixx | General | 2 | January 10th 04 02:33 AM |
A7N8X bootup search for RAID | Tom Braider | Asus Motherboards | 3 | November 21st 03 06:33 PM |