If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
cant u set up ur WD with windows (whatever flavor)
with all ur drivers and stuff then install the IBM drive as master and the WD as slave then in bios set first boot device to IDE 1 IBM = IDE 0 = Master WD = IDE 1 = Slave not perfect but it shoud work "ddtl" this.is@invalid wrote in message ... Hello everybody, I have two HDs: 1) Western Digital, WDC WD800JB specs: http://wdc.custhelp.com/cgi-bin/wdc....ted=1037217622 2) IBM Deskstar 180GXP, IC35L060AVV207 specs: http://www.hgst.com/hdd/desk/ds180gxp.htm IBM's HD is a 2nd HD that i want to install - actually it is not a new HD - i got it (second hand) by warranty after previous HD from that model have died (for a second time in 2 years). The problem is, that however i try to configure those 2 HDs (slave, master, cable select) - whenever IBM's HD is present, WD is not detected (except for one case when WD is slave, IBM master, and they connected accordingly to the cable - WD to a 'slave' part and IBM to a 'master' part, though because of all the combinations i tried i don't remember it 100%, so maybe i plainly wrong). I checked both the cable itself and power connectors (2 power connectors and 2 plugs of an IDE cable) - all of them work if only WD is connected, which means that they are not the problem. Those are the settings i tried (in all the cases primary IDE channel was used): 1) WD master, IBM slave 2) IBM master, WD slave 3) both cable select (three of the above where tried when WB on master's cable, IBM on slave's cable, and the other way around) 4) WB cable select (on master's cable), IBM slave None of those worked. What could be a problem? Could it be that IBM's HD is bad and because of that even WD couldn't be detected? Maybe there could be another problem? ddtl. |
#2
|
|||
|
|||
Unable to detect HDs when second HD is connected
Hello everybody,
I have two HDs: 1) Western Digital, WDC WD800JB specs: http://wdc.custhelp.com/cgi-bin/wdc....ted=1037217622 2) IBM Deskstar 180GXP, IC35L060AVV207 specs: http://www.hgst.com/hdd/desk/ds180gxp.htm IBM's HD is a 2nd HD that i want to install - actually it is not a new HD - i got it (second hand) by warranty after previous HD from that model have died (for a second time in 2 years). The problem is, that however i try to configure those 2 HDs (slave, master, cable select) - whenever IBM's HD is present, WD is not detected (except for one case when WD is slave, IBM master, and they connected accordingly to the cable - WD to a 'slave' part and IBM to a 'master' part, though because of all the combinations i tried i don't remember it 100%, so maybe i plainly wrong). I checked both the cable itself and power connectors (2 power connectors and 2 plugs of an IDE cable) - all of them work if only WD is connected, which means that they are not the problem. Those are the settings i tried (in all the cases primary IDE channel was used): 1) WD master, IBM slave 2) IBM master, WD slave 3) both cable select (three of the above where tried when WB on master's cable, IBM on slave's cable, and the other way around) 4) WB cable select (on master's cable), IBM slave None of those worked. What could be a problem? Could it be that IBM's HD is bad and because of that even WD couldn't be detected? Maybe there could be another problem? ddtl. |
#3
|
|||
|
|||
On Mon, 10 Nov 2003 01:09:47 -0000, "Hope" wrote:
It doesn't help, because HD is not detected at all - when you enter a BIOS setup, it says that no HDs present, so it doesn't even give you an option to set a boot device, because there is none. ddtl. cant u set up ur WD with windows (whatever flavor) with all ur drivers and stuff then install the IBM drive as master and the WD as slave then in bios set first boot device to IDE 1 IBM = IDE 0 = Master WD = IDE 1 = Slave not perfect but it shoud work "ddtl" this.is@invalid wrote in message .. . Hello everybody, I have two HDs: 1) Western Digital, WDC WD800JB specs: http://wdc.custhelp.com/cgi-bin/wdc....ted=1037217622 2) IBM Deskstar 180GXP, IC35L060AVV207 specs: http://www.hgst.com/hdd/desk/ds180gxp.htm IBM's HD is a 2nd HD that i want to install - actually it is not a new HD - i got it (second hand) by warranty after previous HD from that model have died (for a second time in 2 years). The problem is, that however i try to configure those 2 HDs (slave, master, cable select) - whenever IBM's HD is present, WD is not detected (except for one case when WD is slave, IBM master, and they connected accordingly to the cable - WD to a 'slave' part and IBM to a 'master' part, though because of all the combinations i tried i don't remember it 100%, so maybe i plainly wrong). I checked both the cable itself and power connectors (2 power connectors and 2 plugs of an IDE cable) - all of them work if only WD is connected, which means that they are not the problem. Those are the settings i tried (in all the cases primary IDE channel was used): 1) WD master, IBM slave 2) IBM master, WD slave 3) both cable select (three of the above where tried when WB on master's cable, IBM on slave's cable, and the other way around) 4) WB cable select (on master's cable), IBM slave None of those worked. What could be a problem? Could it be that IBM's HD is bad and because of that even WD couldn't be detected? Maybe there could be another problem? ddtl. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to detect a dead CPU? | ck26 | General | 24 | October 11th 03 09:47 AM |
Unable to install Windows 98 | Nathalie | General | 1 | September 26th 03 08:15 AM |
Unable to format the hard drive | Nathalie | General | 5 | September 23rd 03 04:25 AM |
Bios Fails to Detect Hard Drives | Sione Simisi | General | 1 | August 21st 03 07:36 AM |
Can't detect secondary master and slave | cp | General | 4 | August 17th 03 05:28 PM |