A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » System Manufacturers & Vendors » Compaq Computers
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Presario 7994; Parts/Advice Wanted



 
 
Thread Tools Display Modes
  #1  
Old August 13th 04, 10:59 PM
ka6uup
external usenet poster
 
Posts: n/a
Default Presario 7994; Parts/Advice Wanted

I am looking for a couple of the blank-off plates for the drive bays and
the door for the front.
Also, The mouse is not being detected. I am using an USB mouse but will
be using the computer primarily in DOS mode and would like to fix it.
I suspect the connector on the motherboard. The computer detects the
port but not the mouse. The mouse works fine on another computer.
Has anyone run into this problem before?
I am going to try re soldering the connector in case it has come loose,
but the connector appears to be worn and may be no good.
Can anyone suggest a source for the female plug?
TIA
Chuck
  #2  
Old August 14th 04, 12:20 AM
HH
external usenet poster
 
Posts: n/a
Default

The spare part numbers a
Door 158240-001
5.25 blank 102371-001
3.5 blank 102368-001
You can try entering the part numbers at spare parts at:
http://vztxesppro3.cce.hp.com/hppart...64L4GC57AG B1

As for the mouse, are you trying to use a USB mouse in DOS?

HH

"ka6uup" wrote in message
...
I am looking for a couple of the blank-off plates for the drive bays and
the door for the front.
Also, The mouse is not being detected. I am using an USB mouse but will
be using the computer primarily in DOS mode and would like to fix it.
I suspect the connector on the motherboard. The computer detects the
port but not the mouse. The mouse works fine on another computer.
Has anyone run into this problem before?
I am going to try re soldering the connector in case it has come loose,
but the connector appears to be worn and may be no good.
Can anyone suggest a source for the female plug?
TIA
Chuck




  #3  
Old August 14th 04, 02:27 AM
ka6uup
external usenet poster
 
Posts: n/a
Default

No,
I have had no luck getting it to work in DOS. I am using the USB mouse
temporarily till I can figure out why it won't recognize the PS2 mouse.
If you know how to get the USB mouse to work under DOS, PLEASE let me
know. :-}
Thanks for the info on the door.
Chuck

HH wrote:

The spare part numbers a
Door 158240-001
5.25 blank 102371-001
3.5 blank 102368-001
You can try entering the part numbers at spare parts at:
http://vztxesppro3.cce.hp.com/hppart...64L4GC57AG B1

As for the mouse, are you trying to use a USB mouse in DOS?

HH

"ka6uup" wrote in message
...

I am looking for a couple of the blank-off plates for the drive bays and
the door for the front.
Also, The mouse is not being detected. I am using an USB mouse but will
be using the computer primarily in DOS mode and would like to fix it.
I suspect the connector on the motherboard. The computer detects the
port but not the mouse. The mouse works fine on another computer.
Has anyone run into this problem before?
I am going to try re soldering the connector in case it has come loose,
but the connector appears to be worn and may be no good.
Can anyone suggest a source for the female plug?
TIA
Chuck





  #4  
Old August 14th 04, 02:38 AM
ka6uup
external usenet poster
 
Posts: n/a
Default

well I checked out HP and neither part is available.
Thanks anyway
Chuck

HH wrote:

The spare part numbers a
Door 158240-001
5.25 blank 102371-001
3.5 blank 102368-001
You can try entering the part numbers at spare parts at:
http://vztxesppro3.cce.hp.com/hppart...64L4GC57AG B1

As for the mouse, are you trying to use a USB mouse in DOS?

HH

"ka6uup" wrote in message
...

I am looking for a couple of the blank-off plates for the drive bays and
the door for the front.
Also, The mouse is not being detected. I am using an USB mouse but will
be using the computer primarily in DOS mode and would like to fix it.
I suspect the connector on the motherboard. The computer detects the
port but not the mouse. The mouse works fine on another computer.
Has anyone run into this problem before?
I am going to try re soldering the connector in case it has come loose,
but the connector appears to be worn and may be no good.
Can anyone suggest a source for the female plug?
TIA
Chuck





  #5  
Old August 14th 04, 11:19 AM
HH
external usenet poster
 
Posts: n/a
Default

Sorry, but I know of no way a USB mouse will work in DOS since DOS has no
native support for USB. Possibly a USB to PS2 adapter??? Why not just use a
PS2 mouse?
HH

"ka6uup" wrote in message
m...
No,
I have had no luck getting it to work in DOS. I am using the USB mouse
temporarily till I can figure out why it won't recognize the PS2 mouse.
If you know how to get the USB mouse to work under DOS, PLEASE let me
know. :-}
Thanks for the info on the door.
Chuck

HH wrote:

The spare part numbers a
Door 158240-001
5.25 blank 102371-001
3.5 blank 102368-001
You can try entering the part numbers at spare parts at:

http://vztxesppro3.cce.hp.com/hppart...64L4GC57AG B1

As for the mouse, are you trying to use a USB mouse in DOS?

HH

"ka6uup" wrote in message
...

I am looking for a couple of the blank-off plates for the drive bays and
the door for the front.
Also, The mouse is not being detected. I am using an USB mouse but will
be using the computer primarily in DOS mode and would like to fix it.
I suspect the connector on the motherboard. The computer detects the
port but not the mouse. The mouse works fine on another computer.
Has anyone run into this problem before?
I am going to try re soldering the connector in case it has come loose,
but the connector appears to be worn and may be no good.
Can anyone suggest a source for the female plug?
TIA
Chuck








  #6  
Old August 14th 04, 12:10 PM
terry_b17
external usenet poster
 
Posts: n/a
Default

hi,
have you tried a serial mouse ?
hope this helps ,
terry

==============
Posted through www.HowToFixComputers.com/bb - free access to hardware troubleshooting newsgroups.
  #7  
Old August 14th 04, 01:08 PM
terry_b17
external usenet poster
 
Posts: n/a
Default

Chuck,
check out http://www.logitech.com/pub/techsupport/mouse/mouse.txt
good luck ,
terry

==============
Posted through www.HowToFixComputers.com/bb - free access to hardware troubleshooting newsgroups.
  #8  
Old August 14th 04, 03:38 PM
Ben Myers
external usenet poster
 
Posts: n/a
Default

Some motherboards with a more generic BIOS than Compaq's have legacy USB
support, with the right low-level BIOS mapping for a USB keyboard to work in
DOS. As to whether or not a USB mouse will work in DOS with legacy USB support
enabled, I don't know. I have not had the time to experiment. I sort of doubt
it, unless Logitech or maybe some 3rd party driver developer has written a mouse
driver that works with a USB mouse. There are some other USB DOS drivers
lurking around... Ben Myers

On Sat, 14 Aug 2004 06:19:37 -0400, "HH" wrote:

Sorry, but I know of no way a USB mouse will work in DOS since DOS has no
native support for USB. Possibly a USB to PS2 adapter??? Why not just use a
PS2 mouse?
HH

"ka6uup" wrote in message
om...
No,
I have had no luck getting it to work in DOS. I am using the USB mouse
temporarily till I can figure out why it won't recognize the PS2 mouse.
If you know how to get the USB mouse to work under DOS, PLEASE let me
know. :-}
Thanks for the info on the door.
Chuck

HH wrote:

The spare part numbers a
Door 158240-001
5.25 blank 102371-001
3.5 blank 102368-001
You can try entering the part numbers at spare parts at:

http://vztxesppro3.cce.hp.com/hppart...64L4GC57AG B1

As for the mouse, are you trying to use a USB mouse in DOS?

HH

"ka6uup" wrote in message
...

I am looking for a couple of the blank-off plates for the drive bays and
the door for the front.
Also, The mouse is not being detected. I am using an USB mouse but will
be using the computer primarily in DOS mode and would like to fix it.
I suspect the connector on the motherboard. The computer detects the
port but not the mouse. The mouse works fine on another computer.
Has anyone run into this problem before?
I am going to try re soldering the connector in case it has come loose,
but the connector appears to be worn and may be no good.
Can anyone suggest a source for the female plug?
TIA
Chuck








  #9  
Old August 14th 04, 06:59 PM
HH
external usenet poster
 
Posts: n/a
Default

In DOS, USB keyboard, yes, mouse no. Just spend $10 on a PS/2 mouse.
HH

ben_myers_spam_me_not @ charter.net (Ben Myers) wrote in message
...
Some motherboards with a more generic BIOS than Compaq's have legacy USB
support, with the right low-level BIOS mapping for a USB keyboard to work

in
DOS. As to whether or not a USB mouse will work in DOS with legacy USB

support
enabled, I don't know. I have not had the time to experiment. I sort of

doubt
it, unless Logitech or maybe some 3rd party driver developer has written a

mouse
driver that works with a USB mouse. There are some other USB DOS drivers
lurking around... Ben Myers

On Sat, 14 Aug 2004 06:19:37 -0400, "HH" wrote:

Sorry, but I know of no way a USB mouse will work in DOS since DOS has no
native support for USB. Possibly a USB to PS2 adapter??? Why not just use

a
PS2 mouse?
HH

"ka6uup" wrote in message
om...
No,
I have had no luck getting it to work in DOS. I am using the USB mouse
temporarily till I can figure out why it won't recognize the PS2 mouse.
If you know how to get the USB mouse to work under DOS, PLEASE let me
know. :-}
Thanks for the info on the door.
Chuck

HH wrote:

The spare part numbers a
Door 158240-001
5.25 blank 102371-001
3.5 blank 102368-001
You can try entering the part numbers at spare parts at:


http://vztxesppro3.cce.hp.com/hppart...V7F6T9K0U9JCT3

BQC64L4GC57AGB1

As for the mouse, are you trying to use a USB mouse in DOS?

HH

"ka6uup" wrote in message
...

I am looking for a couple of the blank-off plates for the drive bays

and
the door for the front.
Also, The mouse is not being detected. I am using an USB mouse but

will
be using the computer primarily in DOS mode and would like to fix it.
I suspect the connector on the motherboard. The computer detects the
port but not the mouse. The mouse works fine on another computer.
Has anyone run into this problem before?
I am going to try re soldering the connector in case it has come

loose,
but the connector appears to be worn and may be no good.
Can anyone suggest a source for the female plug?
TIA
Chuck











  #10  
Old August 15th 04, 05:20 AM
ka6uup
external usenet poster
 
Posts: n/a
Default

The PS/ mouse doesn't work.
See previous emails.
There is something wrong with the connector
Chuck
HH wrote:
In DOS, USB keyboard, yes, mouse no. Just spend $10 on a PS/2 mouse.
HH

ben_myers_spam_me_not @ charter.net (Ben Myers) wrote in message
...

Some motherboards with a more generic BIOS than Compaq's have legacy USB
support, with the right low-level BIOS mapping for a USB keyboard to work


in

DOS. As to whether or not a USB mouse will work in DOS with legacy USB


support

enabled, I don't know. I have not had the time to experiment. I sort of


doubt

it, unless Logitech or maybe some 3rd party driver developer has written a


mouse

driver that works with a USB mouse. There are some other USB DOS drivers
lurking around... Ben Myers

On Sat, 14 Aug 2004 06:19:37 -0400, "HH" wrote:


Sorry, but I know of no way a USB mouse will work in DOS since DOS has no
native support for USB. Possibly a USB to PS2 adapter??? Why not just use


a

PS2 mouse?
HH

"ka6uup" wrote in message
.com...

No,
I have had no luck getting it to work in DOS. I am using the USB mouse
temporarily till I can figure out why it won't recognize the PS2 mouse.
If you know how to get the USB mouse to work under DOS, PLEASE let me
know. :-}
Thanks for the info on the door.
Chuck

HH wrote:


The spare part numbers a
Door 158240-001
5.25 blank 102371-001
3.5 blank 102368-001
You can try entering the part numbers at spare parts at:


http://vztxesppro3.cce.hp.com/hppart...V7F6T9K0U9JCT3


BQC64L4GC57AGB1

As for the mouse, are you trying to use a USB mouse in DOS?

HH

"ka6uup" wrote in message
y.com...


I am looking for a couple of the blank-off plates for the drive bays


and

the door for the front.
Also, The mouse is not being detected. I am using an USB mouse but


will

be using the computer primarily in DOS mode and would like to fix it.
I suspect the connector on the motherboard. The computer detects the
port but not the mouse. The mouse works fine on another computer.
Has anyone run into this problem before?
I am going to try re soldering the connector in case it has come


loose,

but the connector appears to be worn and may be no good.
Can anyone suggest a source for the female plug?
TIA
Chuck









 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
writing cd`s biggmark Cdr 7 December 31st 04 09:57 AM
Nero help needed foghat Cdr 0 May 31st 04 08:23 PM
Wanted :Compaq Presario 4800 Series restore CD DarthVader000 Compaq Computers 0 April 8th 04 02:47 AM
Presario 524 Maxfax software Mike Calkins Compaq Computers 1 August 12th 03 12:59 AM
Problems with Presario 700 (711AU) SFR Compaq Computers 1 July 8th 03 10:34 AM


All times are GMT +1. The time now is 04:55 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.