If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
GeForce 4200ti freeze-up: At wit's very end.
Suffering, suffering. Any help would be appreciated.
I recently installed Windows XP and have had serious problems with my vid card. Every time I try to run any 3D type application, the screen freezes except for the mouse pointer, which I can move around. Nothing changes for a long time. If I click a few times (3), there is a system beep and then the mouse freezes too. When I reboot, I cannot find any mention in the error log, although perhaps I am not looking in the right place. This happens not only with Direct3D apps (a la DxDiag tests), but ALSO DirectDraw (a la Dx Diag test). I have the latest Nvidia drivers, latest VIA drivers, a fresh system install, tried every AGP setting, tested my RAM. Is it the power supply? 250W is a bit low, but Antecs are supposed to be pretty solid. Also, I've tried unplugging every unnecessary item (PCI cards, CD drives, etc.) and had the exact same behavior. Is it an IRQ conflict? XP dumped the card in with the network, sound, and ACPI, but I can't change it. A problem? Relevant System details: Athlon 900MHz Asylum GeForce 4200 TI 64MB Gigabyte GA-7ZX (rev 1) mobo 256MB RAM Antec 250W PSU Windows XP SP1 DirectX 9.0b (same prob with 8.0) Nvidia drivers 45.23 (latest) (same prob with 30.82, 28.84) Any ideas? And many thanks in advance. Tim |
#2
|
|||
|
|||
the VIA ****... I don't install anything from them. All you need is the =
WinXP CD and Winupdate :-) Check the cooler of the videocard, unmount put thermal grease if = necesary, and look if the fan works fine --=20 F r e e=20 "P. Strongbow" escribi=F3 en el mensaje = om... Suffering, suffering. Any help would be appreciated. =20 I recently installed Windows XP and have had serious problems with my vid card. Every time I try to run any 3D type application, the screen freezes except for the mouse pointer, which I can move around.=20 Nothing changes for a long time. If I click a few times (3), there is a system beep and then the mouse freezes too. When I reboot, I cannot find any mention in the error log, although perhaps I am not looking in the right place. =20 This happens not only with Direct3D apps (a la DxDiag tests), but ALSO DirectDraw (a la Dx Diag test). =20 I have the latest Nvidia drivers, latest VIA drivers, a fresh system install, tried every AGP setting, tested my RAM. =20 Is it the power supply? 250W is a bit low, but Antecs are supposed to be pretty solid. Also, I've tried unplugging every unnecessary item (PCI cards, CD drives, etc.) and had the exact same behavior. =20 Is it an IRQ conflict? XP dumped the card in with the network, sound, and ACPI, but I can't change it. A problem? =20 Relevant System details:=20 Athlon 900MHz Asylum GeForce 4200 TI 64MB Gigabyte GA-7ZX (rev 1) mobo 256MB RAM Antec 250W PSU =20 Windows XP SP1 DirectX 9.0b (same prob with 8.0) Nvidia drivers 45.23 (latest) (same prob with 30.82, 28.84) =20 Any ideas? =20 And many thanks in advance. Tim |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
NV40 ~ GeForce 6800 specs | NV55 | Ati Videocards | 52 | April 20th 04 11:09 PM |
My New Asus Geforce FX v9900 5800 My exp. | Naked Women | Nvidia Videocards | 0 | August 12th 03 04:43 PM |
Asus Gf4 4200ti vs. generic vs. Asus fx5200 | Bob Knowlden | Homebuilt PC's | 4 | August 9th 03 04:59 AM |
Asus Gf4 4200ti vs. generic vs. Asus fx5200 | S.Heenan | Homebuilt PC's | 0 | August 2nd 03 07:38 PM |
GeForce 2 MX400 PCI voltage regulator burned up, missing solder | Beerden | Nvidia Videocards | 3 | July 21st 03 08:58 PM |