If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#41
|
|||
|
|||
Correct angle for keyboard
Osiris wrote:
On 26 Jul 2006 19:14:38 -0700, wrote: correct mouse is also important. I prefer a relatively flat mouse. Some mice are so rounded in the middle that they're just uncomfortable for me to use. Maybe because your wrist is bent up too much ? there is a relation, maybe, with the keyboard slope... Others may prefer that type. The thing is there's no such thing as one size fits all. Nope: we are privileged to have some choice. Keyboard slope, prosthetics, and all that stuff might help, but it won't stop repetitive strain injury (RSI). The only RSI killer is speech-recognition. Good luck. |
#42
|
|||
|
|||
Correct angle for keyboard
H. Seldon wrote
Trev wrote How on earth did those typists manage with three hights of keys, no wrist pads and having to put even force behind the key's. In those days, people who wanted to become 'clerk typists' actually went to school to learn the craft. As part of the required course material, ergonomic work methods were taught. These people learned what furniture (chairs and tables etc) was best suited to the job and as well, they were taught basic things such as correct posture and how to always use the center of the keyboard as the rest/start point. This prevented the hands from having to travel all over the keyboard. No it didnt. On modern computer keyboards these are the F and J keys. Those dont get used enough to matter ergonomically. And the numeric pad is a big improvement on the traditional typewriter keyboard number system ergonomically too. Untrained people suffered the same so-called syndromes as most untrained computer keyboard users suffer today. Doesnt have a damned thing to do with 'training' And most of the 'training' with traditional typewriters was involved with minimising errors, not with the ergonomics anyway. The properly trained person could go to the office and work a full 8 hours with minimal discomfort, in general, while untrained persons would be lucky if they could type continuously for 30 minutes without severe pain especially around the neck and shoulders. You're massively confusing getting used to it with training. The same courses should be required today, for people who use keyboards continuously all day long, minus the hard whacking of the keys. :-) Mindlessly silly. And irrelevant to what is being discussed, THE ANGLE OF THE KEYBOARD. |
#43
|
|||
|
|||
Correct angle for keyboard
Good luck. thank you. |
#44
|
|||
|
|||
Correct angle for keyboard
And irrelevant to what is being discussed, THE ANGLE OF THE KEYBOARD. it is called the SLOPE of the keyboard, silly jester. See ISO 9241-4. Keyboards have too many angles for that to be an adequate term in this. Slope is a word used to indicate a rotation about a horizontal axis, which is meant here. As in the slope of a hill or other unevenness in the terrain, or like in: "Roddy's mind is sliding down a slippery SLOPE at high speed." "Angle" could mean a rotation about ANY axis (2 horizontal, 1 vertical, eg.). Another meaning might be the Miccosoft keyboard where the left and right halves are angled towards the position of the elbow. It is this feature that makes the term "angle" somewhat obscure. So if you could keep the issue clear, I would like to ask you to use the term SLOPE. |
#45
|
|||
|
|||
Correct angle for keyboard
don't pay too much attention to Roddy: he's the group clown.
His mental inadequacies in real life make him come here for social recognition. bear with him. |
#46
|
|||
|
|||
Correct angle for keyboard
Osiris wrote:
And irrelevant to what is being discussed, THE ANGLE OF THE KEYBOARD. it is called the SLOPE of the keyboard, silly jester. Pity about the subject line, child. See ISO 9241-4. Doesnt mandate a particular slope, child. Keyboards have too many angles for that to be an adequate term in this. Tell the OP, child. Slope is a word used to indicate a rotation about a horizontal axis, which is meant here. As in the slope of a hill or other unevenness in the terrain, or like in: "Roddy's mind is sliding down a slippery SLOPE at high speed." "Angle" could mean a rotation about ANY axis (2 horizontal, 1 vertical, eg.). Tell the OP, child. Another meaning might be the Miccosoft keyboard where the left and right halves are angled towards the position of the elbow. It is this feature that makes the term "angle" somewhat obscure. So if you could keep the issue clear, I would like to ask you to use the term SLOPE. You have always been, and always will be, completely and utterly irrelevant, child. What you might or might not like in spades. |
#47
|
|||
|
|||
Correct angle for keyboard
Rod Speed wrote:
Snipped bull**** You truly are a *stupid* ****wit aren't you?? plonk |
#48
|
|||
|
|||
Correct angle for keyboard
Osiris wrote:
snip bear with him. Nah, I don't think so. Lack of knowledge I can obviously understand and abide. *Arrogant* stupidity? That's another story. |
#49
|
|||
|
|||
Correct angle for keyboard
Some pathetic excuse for a bull**** artist claiming to be
H. Seldon desperately attempted to bull**** its way out of its predicament, and fooled absolutely no one at all, as always. Rod Speed wrote: Snipped bull**** You truly are a *stupid* ****wit aren't you?? plonk Fat lot of good that will ever do you, child. |
#50
|
|||
|
|||
Correct angle for keyboard
the critical length of a copper wire is about 4.5 km, defining
critical as breaking by its own weight. (yes, it is independent of it's cross section) Defining the critical length of a thread as the number of follow-up messages, until people start to swear, call names, be stupid, or divert from the original issue in general: What is the critical length of a newsgroup thread ? I vote 20. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Computer Doesn't Keep Correct Date and Time | Brian Wilson | Homebuilt PC's | 5 | March 25th 05 01:20 PM |
how to find the correct Devices after reinstall of XP | Pinger | Dell Computers | 10 | November 19th 04 09:21 AM |
Print Resolution - is this correct | Steven | Printers | 4 | July 30th 04 01:27 PM |
correct dvd writer and reader setup | Andy | General | 1 | October 27th 03 11:13 PM |
Correct way to fit IDE cable? | Peter McVries | General | 5 | September 30th 03 07:39 PM |