If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Xpress Recovery2 problem
I did this backup when I first installed Vista with all of the drivers &
updates installed. I booted from the mb disk, backed up, and all went fine...or so it appeared. Today I decided to test it by hitting "F9" while in the POST screen. Nothing happened. Tried it again, and again. F9 does nothing. The manual says I don't need to use the boot disk after I back up the system. When I look in the disk manager, the backup is there. But F9 still does nothing. What am I missing here? |
#2
|
|||
|
|||
Xpress Recovery2 problem
James wrote:
I did this backup when I first installed Vista with all of the drivers & updates installed. I booted from the mb disk, backed up, and all went fine...or so it appeared. Today I decided to test it by hitting "F9" while in the POST screen. Nothing happened. Tried it again, and again. F9 does nothing. The manual says I don't need to use the boot disk after I back up the system. When I look in the disk manager, the backup is there. But F9 still does nothing. What am I missing here? From the manual * Hard drives in RAID/AHCI mode are not supported. What mode did you use for the hard drive ? HTH, Paul |
#3
|
|||
|
|||
Xpress Recovery2 problem
"Paul" wrote in message
From the manual * Hard drives in RAID/AHCI mode are not supported. What mode did you use for the hard drive ? HTH, Paul Not running RAID/AHCI. I'm running a single drive in IDE native mode. |
#4
|
|||
|
|||
Xpress Recovery2 problem
James wrote:
"Paul" wrote in message From the manual * Hard drives in RAID/AHCI mode are not supported. What mode did you use for the hard drive ? HTH, Paul Not running RAID/AHCI. I'm running a single drive in IDE native mode. Have you checked, that the partition in question was created ? The manual, shows a couple screen shots of "Disk Management" in Windows, where a new partition has been created up near the end of the hard drive. Also, is F9 offered as an option, at the bottom of the screen ? The manual mentions these options at the bottom of the screen. DEL BIOS Setup F9 XpressRecovery2 F12 BootMenu End QFLash Paul |
#5
|
|||
|
|||
Xpress Recovery2 problem
"Paul" wrote in message:
Have you checked, that the partition in question was created ? The manual, shows a couple screen shots of "Disk Management" in Windows, where a new partition has been created up near the end of the hard drive. Also, is F9 offered as an option, at the bottom of the screen ? The manual mentions these options at the bottom of the screen. DEL BIOS Setup F9 XpressRecovery2 F12 BootMenu End QFLash Paul Hi Paul. I appreciate your help here. Disk Manager showed the newly created partition among the unallocated space. If I remember correctly, it was a "healthy" 40GB. And there is still an additional 40GB of unallocated space besides the partition created by Xpress Recovery2. So I left enough space on the drive. Also, the backup stated that it completed successfully. Is the a log somewhere that I might be able to look at? Also, the line you show above is exactly how it appears at the bottom of my POST screen. And everything else works except F9. |
#6
|
|||
|
|||
Xpress Recovery2 problem
David wrote:
"Paul" wrote in message: Have you checked, that the partition in question was created ? The manual, shows a couple screen shots of "Disk Management" in Windows, where a new partition has been created up near the end of the hard drive. Also, is F9 offered as an option, at the bottom of the screen ? The manual mentions these options at the bottom of the screen. DEL BIOS Setup F9 XpressRecovery2 F12 BootMenu End QFLash Paul Hi Paul. I appreciate your help here. Disk Manager showed the newly created partition among the unallocated space. If I remember correctly, it was a "healthy" 40GB. And there is still an additional 40GB of unallocated space besides the partition created by Xpress Recovery2. So I left enough space on the drive. Also, the backup stated that it completed successfully. Is the a log somewhere that I might be able to look at? Also, the line you show above is exactly how it appears at the bottom of my POST screen. And everything else works except F9. Well, I'm running out of things to suggest. Is it possible there is a difference in response, between using a PS/2 keyboard, versus a USB keyboard ? Does the F12 boot menu work ? That would help prove the Fn keys work at the BIOS level. It might be interesting, to plug in a PCI Port 80 POST debugger card, just to see if there is any response noted on the display, when F9 is pressed. That might tell you, if the key was actually routed to a BIOS code module or not. I can find one report here, of someone trying Xpress Recovery2 on another board. And they got it to work. http://groups.google.ca/group/micros...4?dmode=source I tried looking for motherboard reviews, but all I could find is reviews making derogatory references to the feature, and not bothering to test it. Paul |
#7
|
|||
|
|||
Xpress Recovery2 problem
Sorry for the confusion Paul.. I am using my son David's laptop right now. I
forgot about the identity thing. But the post above is from me, James. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
What should I upgrade to? (from Radeon Xpress 200) | Lord Turkey Cough | Ati Videocards | 1 | June 18th 08 06:52 AM |
Radeon® Xpress integrated? | Mtr[_2_] | Dell Computers | 4 | November 25th 07 08:08 AM |
Help! Cant get rid of XPress 2 on bootup | Bob W | Gigabyte Motherboards | 3 | February 13th 07 02:37 AM |
ATI Xpress 200 comparable to?? | Gonzo | Ati Videocards | 2 | November 14th 04 12:38 AM |
Pci Xpress and sli mode ? | Jean | Ati Videocards | 7 | February 28th 04 09:06 PM |