If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Travan tape drive draws tape completely off take-up reel
I've been using a Seagate 20000A (20 GB) Travan tape drive, with Veritas
Backup Exec 4.5a software for 4 years. Recently, the tape drive has malfunctioned. I have put perfectly good tape cartridges into the drive, only to have the tape rewound so far that the tape has been drawn COMPLETELY away from the take-up reel and onto the supply reel. There are 5 pairs of little holes in the leader of the tape, which I believe tell the tape drive where to stop, when rewinding. It is as if the drive is blind to these holes. I opened one tape cartridge, three times, re inserting the tape leader into the take-up reel. I wound the tape manually, far beyond the fifth hole pair. Each time I put the tape into the drive, the drive merely repeats its errant way, rewinding the tape until there is no more tape left to rewind. Before one such exercise, I used a Q-tip soaked in rubbing alcohol to clean a clear plastic item, inside the drive, which I suspected has some sort of optical significance...for recognizing holes in the tape. It didn't help. Has anyone else recognized this problem? Better yet, does anyone know what to clean/fix etc? The only thing I might have done to precipitate this problem was to use a vacuum cleaner to suck dirt out of the tape drive's front opening, a task I have done occasionally, over the years. I see Travan drives for sale, and I suspect I will be buying a new unit. TIA for any help. |
#2
|
|||
|
|||
On Tue, 7 Jun 2005 04:43:05 -0700, "John B" wrote:
Has anyone else recognized this problem? Better yet, does anyone know what to clean/fix etc? The only thing I might have done to precipitate this problem was to use a vacuum cleaner to suck dirt out of the tape drive's front opening, a task I have done occasionally, over the years. They talk about the end of spool sensors getting dirty or being damaged, maybe even getting out of alignment in some drives I guess. The Ditto tape drive I had eons ago was famous for this problem. They were considered one of the worst drives ever. Lots of problems including tapes despooling constantly after a while. People tried to clean them the sensors and the tape cases but it was claimed that you needed to change a resistor which supposedly cured the problem on some drives. Ive read of some tapes having some cleaning cartridge you might want to look around if there is such a thing. Or try to clean the sensor yourself if there is no alternative. I think there was a light that was supposed to show through the hole and hit a sensor to let it know it was the end of the tape. The Ditto cartridge had these little mirrors in the casing of the tape to direct the light beam. |
#3
|
|||
|
|||
Your recollections are helpful. Now I realize that each tape cartridge
contains a right-angular mirror. I used a high-intensity desk lamp and clearly saw the ability of the tape cartridge to turn the light 90 degrees. This was apparent in the cartridge that had its tape medium fully withdrawn, so no tape was blocking the path of the light. Looking inside the tape drive, I then saw clear plastic in the exact position to exploit the cartridge's mirror. No visible light is apparent. I have cleaned the plastic surfaces. I am wondering if the light is supposed to be visible. I have a friend who has an identical drive, at his workplace, and I'll ask him to peer inside his drive. So I just repaired the tape cartridge again, and inserted it in the drive. It promptly failed, unwinding the tape again. I suppose the light emitter is dead. Seems implausible, considering the 330K hour MTBF listed...at least for current models. But your advice that these drives are notorious is worthwhile. It served me well for 4 years. My friend's is probably 6 years old by now. " wrote in message ... On Tue, 7 Jun 2005 04:43:05 -0700, "John B" wrote: Has anyone else recognized this problem? Better yet, does anyone know what to clean/fix etc? The only thing I might have done to precipitate this problem was to use a vacuum cleaner to suck dirt out of the tape drive's front opening, a task I have done occasionally, over the years. They talk about the end of spool sensors getting dirty or being damaged, maybe even getting out of alignment in some drives I guess. The Ditto tape drive I had eons ago was famous for this problem. They were considered one of the worst drives ever. Lots of problems including tapes despooling constantly after a while. People tried to clean them the sensors and the tape cases but it was claimed that you needed to change a resistor which supposedly cured the problem on some drives. Ive read of some tapes having some cleaning cartridge you might want to look around if there is such a thing. Or try to clean the sensor yourself if there is no alternative. I think there was a light that was supposed to show through the hole and hit a sensor to let it know it was the end of the tape. The Ditto cartridge had these little mirrors in the casing of the tape to direct the light beam. |
#4
|
|||
|
|||
"John B" wrote Looking inside the tape drive, I then saw clear plastic in the exact position to exploit the cartridge's mirror. No visible light is apparent. I have cleaned the plastic surfaces. I am wondering if the light is supposed to be visible. I have a friend who has an identical drive, at his workplace, and I'll ask him to peer inside his drive. My friend reports no visible light inside his tape drive, which is known to be good. In both our cases, the amber indicator light, for the bezel, still operates. It's irrelevant. I get my amber indicator to turn on by sliding a blunt instrument into the tape drive opening, so as to gently depress tiny nylon buttons on the far left. Incidentally, I have a Certance cleaning tape, and it did not help this problem. |
#5
|
|||
|
|||
On Tue, 7 Jun 2005 09:14:49 -0700, "John B" wrote:
"John B" wrote Looking inside the tape drive, I then saw clear plastic in the exact position to exploit the cartridge's mirror. No visible light is apparent. I have cleaned the plastic surfaces. I am wondering if the light is supposed to be visible. I have a friend who has an identical drive, at his workplace, and I'll ask him to peer inside his drive. My friend reports no visible light inside his tape drive, which is known to be good. In both our cases, the amber indicator light, for the bezel, still operates. It's irrelevant. I get my amber indicator to turn on by sliding a blunt instrument into the tape drive opening, so as to gently depress tiny nylon buttons on the far left. Incidentally, I have a Certance cleaning tape, and it did not help this problem. Thats interesting if you are saying the light itself is irrelevant. See heres a description of the a typical tape sensor Tape Despools If tapes you use in your tape drive frequently despool, the end-of-tape sensor in your tape drive may be dirty or damaged. The end-of-tape sensor detects the end of a tape by projecting light through a series of holes near the end of the tape. If the bulb used to project this light is dirty or is damaged, the light may not be strong enough to project through the holes. This prevents the drive from accurately determining when the end of the tape has been reached. Many drive manufacturers recommend cleaning the end-of-tape sensor after every eight hours of drive operation, when excessive dust or other debris accumulates on the sensor, or when a tape used in the drive becomes despooled. For information about cleaning the end-of-tape sensor in your tape drive, refer to the documentation that came with the drive, or contact the drive manufacturer. I suppose an Ebay used tape drive just to get the data from your tape would be a way to go and then switch over to something else. I spent 4-5 hundred bucks on tapes on sale and was dreaming of a cheaper knock off of the Zip Disks which were coming out at the time but when I saw the CD burners that were new then I knew that was the way to go. Of course now Id use a DVD burner for smaller amounts of data and an external HD for big backups. |
#6
|
|||
|
|||
I am devoted to the tape method. I bought a brand-new 10/20 GB Certance
Travan tape drive for $160, including shipping and tax; from ZipZoomFly.com. Thus I have 3 years of warranty (2 mfg + 1 VISA card). I even got Yosemite software, which I have yet to implement, and a 10/20 GB Certance tape, to boot. It works great. Someday, I'll peer into that old tape drive and try to figure out how to fix it! (not likely) I've never been able to fix a tape drive. They are replacement items, in my book. Thanks for your replies. " wrote in message I suppose an Ebay used tape drive just to get the data from your tape would be a way to go and then switch over to something else. I spent 4-5 hundred bucks on tapes on sale and was dreaming of a cheaper knock off of the Zip Disks which were coming out at the time but when I saw the CD burners that were new then I knew that was the way to go. Of course now Id use a DVD burner for smaller amounts of data and an external HD for big backups. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Removable Hard Drive Bay Problems Anyone? | Rus | General | 48 | May 22nd 05 04:19 AM |
Fiber channel tape drive config help | Kyle Tucker | Storage & Hardrives | 8 | December 28th 04 04:08 AM |
Question about transfer speeds between HDs, and DMA mode | ZigZag Master | Storage (alternative) | 25 | July 25th 04 09:56 PM |
Removable Drive Bays | Rod Speed | Storage (alternative) | 35 | January 3rd 04 08:31 PM |
Help With Locked Hard Drive | Louis Bybee | Storage (alternative) | 29 | November 22nd 03 03:01 PM |